Schlage L-SERIES User manual

*P516-871*
P516-871
L-Series Electried Lock
All installations should be in accordance with local electrical codes and national electrical code, NFPA 70.
L909X-Series and LM929X-
Series electried locks offer
selection between one of
two modes, EL or EU.
Select the appropriate mode
for the installation using the
mode select switch located
on the mortise chassis.
EL, electrically locked
(fail safe):
Outside knob/lever or both
outside and inside knobs/
levers (depending on
function) will lock when
power is applied. In the
event of power failure, the
opening will be unlocked.
EU, electrically unlocked
(fail secure):
Outside knob/lever or both
outside and inside knobs/
levers (depending on
function) will unlock when
power is applied. In the
event of power failure, the
opening will be locked.
Note: When mode is switched (from EL to EU or EU to EL) the lock requires a complete lock/unlock power cycle to synchronize to
the proper mode.
IMPORTANT! Connection of L-Series electried mortise locks to a supply circuit containing electromagnetic devices (i.e., solenoid based) is not
recommended. If used, the resulting transient voltages could damage the lock. The transient voltage must be carefully suppressed at the equipment
producing it before connecting the lock to the same circuit. A varistor rated at 35 V (peak recurrent) may be used for transient voltage protection.
Troubleshooting
If lock does not operate.
• Ensure the lock is powered with DC power. Do not use AC power.
• Ensure the input voltage is between 10.8 and 26.4 volts DC.
L-Series Request-to-Exit (RX) Lock
RX utilizes a microswitch inside the lock case to detect rotation of the inside knob/lever. The switch then signals the use of the opening to the security system.
The RX is a removable module located on the bottom edge of the lock chassis. The module must be properly positioned to detect inside knob/lever
rotation. If not properly positioned, the lock and/or microswitch may be damaged.
Note: RX is not applicable with LM929X-Series locks.
RX module installation
1. The microswitch must be on the same side of the door as the
handing screw (facing the inside of the door).
2. Install the RX switch module as shown.
Change lock handing with RX
1. If the RX module is installed, remove the RX module.
2. Remove the handing screw.
3. Rotate the latch 180° (if necessary).
4. Reinstall the handing screw on the appropriate side.
5. Reinstall the RX module with the microswitch on the same side as
the handing screw.
Electrical rating: 3 A, 125 V AC; 2 A, 30 V DC
L-Series Electried Locks
L909X-Series Electried Mortise Lock,
LM929X-Series Electried Two-Point Lock
Wiring Instructions and Specications
Handing screw
RX module
screws
Microswitch
Blue (NO)
Yellow (NC)
Green
(common)
WARNING
Warnings indicate potentially hazardous conditions, which if not
avoided or corrected, may cause death or serious injury.
WARNINGS
L909X
LM929X
Mode select
switch
Electried hinge/
EPT (not furnished)
12 or 24 V DC
Install varistor
here if used
(not furnished)
Switch
(not furnished)
Power supply
12 or 24 V DC
(not furnished)
Lock to hinge/EPT
harness (not furnished)
Electrical Requirements:
The L909X and LM929X-Series electried locks
are powered by DC power only.
Do not use AC power.
• Voltage: 12 or 24 V DC (maximum 26.4 V,
minimum 10.8 V)
• Peak current: 0.4 amps
• Holding current: 0.010 amps
• Operating temperature: -22°F to 140°F
(-30°C to 60°C)
Note: Either lock wire may be attached to either power
supply terminal (+ or -).
Maximum Total Wire Length
AWG 14 16 18 20
Voltage
12 V 500'
(152 m)
300'
(91 m)
200'
(61 m)
100'
(30 m)
24 V Up to 1000' 304 m
WARNING
L9091/93/95, L9493/95 and LM9291/93/95 functions lock both inside and
outside levers. Locking both levers will prevent normal egress from the
inside and will prevent the intended operation of an emergency exit.

© Allegion 2015
Printed in U.S.A.
P516-871 Rev. 10/15-d
Customer Service
1-877-671-7011 www.allegion.com/us
Deadbolt Monitor (DM)
Deadbolt Monitor (DM) identies the status of the deadbolt (extended or retracted). Normally open, normally closed, and common connections are
provided. Note: Deadbolt monitor is only available on deadbolt models. Electrical rating: 3 A, 125 V AC; 2 A, 30 V DC.
Latchbolt Monitor (LX)
Latchbolt Monitor (LX) identies the status of the latchbolt (extended or retracted). Normally open, normally closed, and common connections
are provided. Electrical rating: 3 A, 125 V AC; 2 A, 30 V DC.
Door Position Sensor (DPS)
Door Position Sensor (DPS) detects the position of the door, open
or closed, by utilizing a sensor in the mortise lock to detect a magnet
located in the door strike. Normally open, normally closed, and common
connections are provided. Note: DPS is not available on deadbolt models.
Max voltage 175 VDC, max current 0.250 A
DPS strike box
Strike
(10-072 shown)
Magnet
Allegion Connect
The L909X-Series and LM929X-Series electried mortise locks are furnished with Allegion Connect, a factory-installed Molex® connector system that
provides simplied installation and maintenance. The system utilizes quick-connect harnesses and hinges. As an alternative installation method, the
Molex connector may be cut off and the lock installed with traditional wire splicing methods.
Note: The items listed and shown below reect options that may or may not be included with your specic model.
Variable length wiring
harness (6" to 192")
EPT or electried hinge
6” wiring harness To
power
supply
RX/LX/DPS
RX/LX/DM
1234
5678
12
34
4-pin
connector
1
23
4
5678
12
34
8-pin
connector
L909X available options:
RX = Request to exit
DM = Deadbolt monitor
DPS = Door position sensor
LX = Latchbolt monitor
LM929X available options:
None
See charts below for wire colors.
8-Pin Lock
Connector
Harness
Connector
Purpose Function Wire
Color Pin Pin Wire
Color
EL / EU Power* Black 1
▬
► 1 Red
Power* Black 2
▬
► 2 Black
RX
Normally Open (NO) Blue 3
▬
► 3 Blue
Normally Closed (NC) Yellow 4
▬
► 4 Yellow
Common (C) Green 5
▬
► 5Green
LX
Normally Open (NO) Gray 6
▬
► 6 Gray
Normally Closed (NC) Violet 7
▬
► 7 Violet
Common (C) White 8
▬
► 8White
* Lock auto-detects GND, +12 or +24 V DC
4-Pin Lock
Connector
Harness
Connector
Purpose Function Wire
Color Pin Pin Wire
Color
DM
Normally Open (NO) Orange 1
▬
► 1 Orange
Normally Closed (NC) Brown 2
▬
► 2 Brown
Common (C) Pink 3
▬
► 3 Pink
not used 4 4 Tan
DPS
Normally Open (NO) Green/black 1
▬
► 1 Orange
Normally Closed (NC) Red 2
▬
► 2 Brown
Common (C) White/black 3
▬
►
3 Pink
not used 4 4 Tan