Schlage Control Series User manual

All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
Install Guide
Schalge Control Series
Verkada Inc. 406 E 3rd Ave, San Mateo, CA 94401
[email protected]

Document
Document Details
Verkada Inc. 406 E 3rd Ave, San Mateo, CA 94401
[email protected]
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
V1.0 (20230808)
(V1.0 first published 20230808)
Firmware
Firmware version can be verified on
Verkada Command command.verkada.com.
2

Introduction
Introduction
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
3
This setup guide provides instructions on how to
integrate SchIage Control locks into Verkada
Command.
For all Schlage documentation including lock
installation and datasheets, please reach out to your
Allegion representative or visit the Allegions Website.
Background
Schlage Control Locks were designed specifically with multi-tenant units in mind. These locks offer
a great alternative to hard wiring a door, particularly when doing so would be cost restrictive. The
Control lock comes in two versions: the standalone deadbolt, and the interconnected deadbolt
handle.
This wireless lock integration is different than our previous one. The Control lock communicates
with it’s hub (GWE) on the 2.4 Ghz band. The GWE is put in IP mode and will need an ethernet
connection. No Verkada equipment is required in this integration. The GWE will communicate
directly with the Allegion Engage site which in turn communicates directly with Command.
Integration Process
The integration process should be split into two phases. Phase 1 is to properly set up and configure
your Schlage locks. Installation and configuration steps include:
●Installing the Control locks.
●Installing the GWE Hub.
●Creating engage sites in Command.
●Commissioning GWEs hubs and Locks.
●Linking the hubs and locks.
●Verifying connection and signal strength in Engage App.
You can contact Allegion support to troubleshoot any issues you may have during this phase.
Phase 2 is to setup and configure your locks and settings in Verkada Command. Steps include:
●Syncing your Command Site(s).
●Verifying remote unlock and user key card unlock functionality.
Verkada Inc. 406 E 3rd Ave, San Mateo, CA 94401
[email protected]

Introduction
Common use cases
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
4
The primary use case for the Schlage Control series is for multi-tenant units. These will be
controlling residential living spaces such as dormitories, apartments, and condos.
Universities
These locks are a great option for dorm room access control.
In multi-tenant
Officeses, Supply closets.
These verticals use wireless locks because they do not require expensive wiring to be run
through walls and allow much more flexibility. They are also much more cost effective than
wired doors. This integration allows us to work with existing customers with Schlage Control
wireless locks.
Important notes
Tips to ensure a successful installation:
●Read all of the Schlage Control and GWE Hub documentation for the lock series being
installed.
●Verkada support will NOT troubleshoot Schlage hardware!
●Wireless locks are wireless products so wireless range is always a concern, please
ensure that the GWE is placed within range of all the connected locks.
Verkada Inc. 406 E 3rd Ave, San Mateo, CA 94401
[email protected]

Installation
GWE HUB Configuration
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
[email protected]
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
5
All configuration and setup of the Control Locks themselves as well as the GWE hubs will
be guided by Schlage documentation included in the locks and hubs packaging.
However, during the process you will need to input some verkada endpoints in order for
the Hub to communicate with the Verkada backend. Below is a screenshot of this window
in the Engage app accompanied by the Endpoints themselves.
https://engage.vkdaapi.com/engage/wss
https://engage.vkdaapi.com/engage/newCA/current

Installation
Command Configuration
1. Create a new Verkada Site with no Verkada equipment.
2. Create Engage Site
a. In the Settings page of your Verkada site, click Create Site. This will create an
Engage site and prompt an automated email to be sent to the email associated
with the user. YOU MUST USE THE SITE THAT VERKADA CREATES IN ENGAGE. Not
one you have created.
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
[email protected]
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
6

Installation
Command Configuration
3. Once all configuration has been completed on the Engage app and the devices are
paired, click the SYNC button to pull the configurations into Command. If your
configuration was all correct, you will have functioning locks in the site!
4. Verify that the lock shows up in Command. Add a User or Group and test the remote
unlock with an account that has been given access.
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
[email protected]
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
7

Appendix
Support
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
[email protected]
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
Thank you for purchasing this Verkada product. If for any reason
things don’t work right, or you need assistance, please contact us
immediately.
verkada.com/support
Sincerely, The Verkada Team
8