Sealey PCB35 User manual

PCB35 - 1 - 170504
Thank you for purchasing a Sealey Product. Manufactured to a high
standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT:PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLYAND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAYCAUSE DAMAGE AND/OR PERSONAL INJURYAND WILL INVALIDATE
THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
pWARNING! The blades used by this cutter are razor sharp and should be treated with due caution.
3Store the cutter in a safe childproof place when not in use.
3Use in a suitable, clean and tidy work area, free from unrelated materials. Ensure there is adequate lighting.
3Use the cutters for rubber and soft vinyl pipes only.
7DO NOT use cutter on hard reinforced pipe. If the
blade does not penetrate the pipe, then the materials
used to make the pipe are too hard. Applying
excessive pressure may cause the pipe to shatter.
7DO NOT continue to attempt cutting any pipe that
withstands penetration.
7DO NOT insert a finger into the cutting area at any time.
7DO NOT turn the pipe whilst cutting.
7DO NOT allow untrained people to use the cutters.
7DO NOT allow children to use or play with the cutters.
7DO NOT use the cutter for a task it is not designed to perform.
7DO NOT operate cutter if any parts are damaged or missing as this
may cause failure and/or personal injury.
7DO NOT operate the cutter when you are tired, under the influence of alcohol,
drugs or intoxicating medication.
2. INTRODUCTION
INSTRUCTION MANUAL FOR:
OVERHEAD PLASTIC
PIPE CUTTER
MODEL: PCB35
The PCB35 plastic pipe cutter has a die cast aluminium body with a heat treated AUS-8 grade stainless steel blade.
Features ratchet action cutting to avoid the crushing of pipes and push button blade retraction. Suitable for cutting
plastic pipes and extrusions. Cutting capacity 6mm to 35mm pipes.
3. OPERATING THE CUTTER
3.1. OPERATING THE CUTTER
3.1.1. Place the plastic pipe into the U jaw with the
blade point aligned with the tube centre.
Repeatedly squeeze the trigger handle to
pierce and cut through the pipe.
3.2. RETRACTING THE BLADE
3.2.1. To retract the blade after cutting squeeze the
handles together and press the retraction
button as shown at 1 above.
p p
WARNING! Ensure you read, understand and apply safety instructions.
PCB35 - 1 - 170504
Thank you for purchasing a Sealey Product. Manufactured to a high
standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT:PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLYAND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAYCAUSE DAMAGE AND/OR PERSONAL INJURYAND WILL INVALIDATE
THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
pWARNING! The blades used by this cutter are razor sharp and should be treated with due caution.
3Store the cutter in a safe childproof place when not in use.
3Use in a suitable, clean and tidy work area, free from unrelated materials. Ensure there is adequate lighting.
3Use the cutters for rubber and soft vinyl pipes only.
7DO NOT use cutter on hard reinforced pipe. If the
blade does not penetrate the pipe, then the materials
used to make the pipe are too hard. Applying
excessive pressure may cause the pipe to shatter.
7DO NOT continue to attempt cutting any pipe that
withstands penetration.
7DO NOT insert a finger into the cutting area at any time.
7DO NOT turn the pipe whilst cutting.
7DO NOT allow untrained people to use the cutters.
7DO NOT allow children to use or play with the cutters.
7DO NOT use the cutter for a task it is not designed to perform.
7DO NOT operate cutter if any parts are damaged or missing as this
may cause failure and/or personal injury.
7DO NOT operate the cutter when you are tired, under the influence of alcohol,
drugs or intoxicating medication.
2. INTRODUCTION
INSTRUCTION MANUAL FOR:
OVERHEAD PLASTIC
PIPE CUTTER
MODEL: PCB35
The PCB35 plastic pipe cutter has a die cast aluminium body with a heat treated AUS-8 grade stainless steel blade.
Features ratchet action cutting to avoid the crushing of pipes and push button blade retraction. Suitable for cutting
plastic pipes and extrusions. Cutting capacity 6mm to 35mm pipes.
3. OPERATING THE CUTTER
3.1. OPERATING THE CUTTER
3.1.1. Place the plastic pipe into the U jaw with the
blade point aligned with the tube centre.
Repeatedly squeeze the trigger handle to
pierce and cut through the pipe.
3.2. RETRACTING THE BLADE
3.2.1. To retract the blade after cutting squeeze the
handles together and press the retraction
button as shown at 1 above.
p p
WARNING! Ensure you read, understand and apply safety instructions.
pcb35 pipe cutter.qxd 6/10/2004 08:56 Page 1

PCB35 - 1 - 170504
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component
parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of this equipment. WARRANTY: Guarantee is 12
months from purchase date, proof of which will be required for any claim. INFORMATION: For a copy of our latest catalogue and
promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
E-mail: [e-mail]
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
Web address: www.sealey.co.uk
54
3
2
3
21
3.3. CHANGING THE BLADE (Part number PCB35/B)
3.3.1. Rotate the black spring retaining lever in the handle so
that the hook retracts from the spring eyelet thus
releasing the spring. (See fig.1-A).
3.3.2 Hold the cutter with the head facing downwards so
that gravity will assist the blade out. Depress the
handle repeatedly to extend the blade as far as
possible. (See fig.2-B) Ease the blade outwards until
the spring is visible then disconnect the spring using
thin nosed pliers. (See fig.2-C) Remove the spring
making note of its orientation for reassembly.
3.3.3 Slide the blade carefully out of the top of the tool as
shown in fig.3-D.
3.3.4 Slide the new blade partway into the tool as shown in
fig.4-E. With the eyelet flat to the blade, slide the
spring into the body of the tool and reconnect the
hooked end of the spring into the circular hole in
the blade. (See fig.4-F).
3.3.5 Depress the trigger handle and retraction button
simultaneously and ease the new blade back into
the body of the tool. (See fig.4-E)
3.3.6 When the spring reappears adjacent to the black
spring retaining lever (See fig.5-H) rotate the lever so
that the hook re-engages with the spring eyelet. ( I )
PCB35 - 1 - 170504
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component
parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of this equipment. WARRANTY: Guarantee is 12
months from purchase date, proof of which will be required for any claim. INFORMATION: For a copy of our latest catalogue and
promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
E-mail: [e-mail]
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
Web address: www.sealey.co.uk
54
1
3.3. CHANGING THE BLADE (Part number PCB35/B)
3.3.1. Rotate the black spring retaining lever in the handle so
that the hook retracts from the spring eyelet thus
releasing the spring. (See fig.1-A).
3.3.2 Hold the cutter with the head facing downwards so
that gravity will assist the blade out. Depress the
handle repeatedly to extend the blade as far as
possible. (See fig.2-B) Ease the blade outwards until
the spring is visible then disconnect the spring using
thin nosed pliers. (See fig.2-C) Remove the spring
making note of its orientation for reassembly.
3.3.3 Slide the blade carefully out of the top of the tool as
shown in fig.3-D.
3.3.4 Slide the new blade partway into the tool as shown in
fig.4-E. With the eyelet flat to the blade, slide the
spring into the body of the tool and reconnect the
hooked end of the spring into the circular hole in
the blade. (See fig.4-F).
3.3.5 Depress the trigger handle and retraction button
simultaneously and ease the new blade back into
the body of the tool. (See fig.4-E)
3.3.6 When the spring reappears adjacent to the black
spring retaining lever rotate the lever so that the hook
re-engages with the spring eyelet.
pcb35 pipe cutter.qxd 6/10/2004 08:56 Page 2