Sealey SSG1P/3.V3 User manual

2L PRESSURE POT FOR SSG1P
MODEL NO: SSG1P/3.V3
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURYAND WILL INVALIDATE THE WARRANTY.
1. SAFETY
9Familiarise yourself with the application, limitations and potential hazards peculiar to the spray gun.
WARNING! Disconnect the spray gun from the air supply before changing accessories, servicing or
performing any maintenance.
9Maintain the spray gun in good condition (use an authorised service agent).
9Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous
and will invalidate the warranty.
9Keep the spray gun clean for best and safest performance.
9Ensure that the compressed air system can supply the spray gun air consumption (7-12cfm).
9Wear approved safety respiratory protection and safety eye goggles.
9If spraying isocyanate based finisher, wear approved respirator/clean air breathing apparatus and
protect skin with latex gloves and an impervious hooded coverall.
9Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and tie back long hair.
9Locate the spray gun in a suitable work area. Keep area clean and tidy and free from unrelated materials
and ensure that there is adequate ventilation and lighting.
9Keep children and unauthorised persons away from the work area.
9When not in use, ensure that the air supply is turned off.
9Avoid unintentional operation of spray gun.
8DO NOT point spray gun at yourself, other persons or animals.
8DO NOT direct air from the air hose at yourself, other persons or animals.
8DO NOT carry the spray gun by the hose, or pull the hose from the air supply.
8DO NOT exceed the maximum air pressure of 78psi.
8DO NOT use the spray gun for any purpose other than that for which it is designed.
8DO NOT allow untrained persons to operate the spray gun.
8DO NOT get the spray gun wet or use in damp or wet locations or in areas where there is condensation.
8DO NOT operate the spray gun if any parts are missing or damaged as this may cause failure and/or personal injury.
9When not in use, disconnect the spray gun from the air supply, clean thoroughly and store safely.
2. INTRODUCTION
Pressure pot suitable for use with Model No. SSG1P Pressure Pot Spray Gun.
3. SPECIFICATION
Model No.: .........................................................SSG1P/3.V3
Description:...................................................2L Pressure Pot
4. ASSEMBLY
4.1. Connect the air and paint hoses in the following manner.
a: Blue air hose from pressure regulator to gun handle.
b: Clear hose from Pot paint outlet to inlet on underside of nozzle on gun.
4.2. Initially screw parts hand tight to avoid cross-threading. If a part cannot easily be turned by hand, check that you have the correct part, or
unscrew, realign and try again. DO NOT use excessive force when assembling.
5. CLEANING/MAINTENANCE
WARNING! Disconnect from the air supply before attempting any maintenance or cleaning.
5.1. When finished spraying, wipe the outside of the pot and fittings with a dampened solvent rag.
Refer to
instruction
manual
Original Language Version
© Jack Sealey Limited SSG1P-3.V3 Issue 1 11/10/21

5.2.
5.3.
.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 [e-mail] www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call
our technical team on [e-mail] or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Parts support is available for this product. Please email [e-mail] or telephone [phone]
Original Language Version
© Jack Sealey Limited SSG1P-3.V3 Issue 1 11/10/21