Sealey Stw101 Firmware update

3.1. Hold the torque wrench in your left hand (if right handed) so that the

required scale on the shaft, just above the hand grip - is uppermost and

visible.

3.2. Turn the lock screw, in the end of the grip, counter-clockwise to unlock grip

(STW201.V2 has a locking plug in the end of the grip - pull ring to unlock).

3.3. Turn grip to select torque setting as follows:

 

 

and the ‘zero’ on the grip graduation is aligned with the centre line of

the shaft scale.

 

aligned with the centre line to give a

Note: If using the alternative scale (lb.in, lb.ft or kg.m depending on

wrench) then each division of the grip graduation is equivalent to

the scale increment divided by the number of divisions. For

example (STW1011):

The alternative scale is in lb.ft.

 

There are 7 grip divisions.

 

3.4. Tighten the lock screw at the end of the handle to prevent accidental

alteration of the setting.

3.5.

mechanism click when the set torque is reached. Immediately stop

 

The wrench will reset ready for the next application.

Note: If wrench is not used for some while, operate it a few times, at a

low setting, to ensure that all internal parts are coated in grease.

 Ensure all workshop safety rules, regulations, and conditions are complied with when using the torque wrench.

 Maintain the wrench in good condition and replace any damaged or worn parts. Use genuine parts only. Unauthorised parts may be dangerous and will

invalidate the warranty.

 The wrench is a precision tool, DO NOT abuse it.DO NOT drop or throw the wrench.

 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.

WARNING! DO NOT use the wrench if damaged or thought to be faulty (contact Service Agent).

 DO NOT use wrench unless you have been instructed in its use by a qualified person.

 DO NOT use any cleaner which might affect the high pressure grease with which the wrench is packed.

After use adjust to lowest torque setting (but not below),clean and store in a safe, dry, childproof location.

2.1. Introduction

These torque wrenches are precision tools and each is supplied with a calibration certificate. Torque setting is by means of a micrometer type adjuster and the drive

head has a reversible ratchet.

Thank you for purchasing a Sealey Product. Manufactured to a high standard this tool will, if used according to these instructions and properly maintained, give years of trouble free performance.



TORQUE WRENCHES

1. SAFETY INSTRUCTIONS

2. INTRODUCTION & SPECIFICATIONS

3. OPERATION

4. RECALIBRATION

5. CALIBRATION CERTIFICATE

4.1 To ensure continued accuracy the wrench should be

recalibrated annually and after any impact or other misuse.

 

5.1 

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT

CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL

INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

Original Language Version 

STW200, STW201.V2, STW202, STW1012 (I) 

2.2. Specifications

Model No. .........STW101 ....STW1011 ...STW102 ....STW103 . . . STW104 .... STW200 ...STW201.V2 ....STW202 ...STW1012

 .. .......7-112 ...... ..... ....  .... 10-110 .....30-210 ........ ....

Alternative Scale .... .. .... .... ..  ... ..... . 

Drive (sq) .......... ........ ........ ........ .......  ........  .........................

Length (mm) ........ ........370 ........ ........ . . . . . . . 1070 .......  .................. .......

 STW101 STW1011 STW102 STW103 STW104 STW200 STW201.V2 STW202 STW1012

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.

IMPORTANT: 

WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.

INFORMATION:

01284 757500

01284 703534

sales@sealey.co.uk

Sole UK Distributor, Sealey Group,

Kempson Way, Suffolk Business Park,

Bury St. Edmunds, Suffolk,



www.sealey.co.uk

Web

TORQUE WRENCH CALIBRATION CERTIFICATE

Models: STW101, STW1011, STW102, STW103, STW104,

STW200, STW201.V2, STW202 & STW1012

Original Language Version 

STW200, STW201.V2, STW202, STW1012 (I) 

700















370.2





110







31.2





STW 200

110





STW202











7.1







STW1012

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.

IMPORTANT: 