Sealey Professional TOOLS SA3702 User manual

Max. Inflation Pressure: . . . . . . . . . . . . . . . . .10bar (145psi)
Max. Inlet Pressure: . . . . . . . . . . . . . . . . . . . .16bar (232psi)
Accuracy: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+/-0.5%
Input: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .230V
Hose Length: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7.6mtr
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according
to these instructions and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL
REQUIREMENTS, WARNINGS, AND CAUTIONS. USE THIS PRODUCT CORRECTLY, AND WITH CARE
FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE
AND/OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY.
DIGITAL TYRE INFLATOR
(WALL MOUNTED)
Model: SA3702
1. SAFETY INSTRUCTIONS
2. INTRODUCTION & SPECIFICATION
3. PREPARING INFLATOR FOR USE
4. OPERATING INSTRUCTIONS
Professional wall-mounted forecourt unit with robust aluminium die-cast casing. Simple to use with large 30mm LCD display
and electronic push-button control. Auto start inflation feature with audible and visual end-of-cycle signal. Accurate pressure
delivery reduces tyre wear, extends tyre life, improves fuel economy and increases safety. Supplied with 7.6 metres of
high-pressure hose and twin hold-on connector.
In order to provide a trouble-free operation it is necessary to connect the power supply from the main switchboard with a MAX
3amp fuse/RCB protection device. This unit must be grounded.
The circuit breaker should be marked as the disconnecting device for the equipment.
Please refer to figure 1 (overleaf) when reading the following instructions:
p p
WARNING! if you are inflating a flat tyre, make sure you press the FLAT TYRE button before inflation, this
function will use 10 short pulses of air to begin the inflation, this is recommended for tyres with a pressure of 4
psi/0.3 bar or less.
4.1 Ensure the following
4.1.1 Upon start-up, the display automatically shows the software level (e.g P3.4).
4.1.2 That you do not connect the hose to the tyre during start-up.
4.2 Operation
4.2.1 Set required pressure using the +/- buttons.
4.2.2 Connect the hose to the tyre - the filling process will start automatically.
4.2.3 The inflator will sound when desired pressure is reached, also the display will read END.
4.2.4 After 90 seconds of being idle the unit will revert to its Default Safe Setting
4.2.5 To continue at the same pressure start from step 4.2.2, if different pressure is required begin from step 4.2.1.
3Keep the inflator clean and in good condition.
3Keep children and non-essential persons away from the work area.
p p
WARNING! This inflator is capable of producing a high pressure. DO NOT inflate any item beyond its maximum
specified pressure.
7DO NOT direct inflation hose connector head at yourself, others or animals.
7DO NOT leave the inflator operating unattended. Always monitor the inflation pressure.
7DO NOT yank the hose from an inflation valve.
7DO NOT get the inflator wet or use in the rain, it is recommended that it is installed under shelter.
7DO NOT use the inflator for a task it is not designed for.
3Check exact pressure required for task, refer to tyre/vehicle manufacturers instructions.
7DO NOT exceed recommended tyre pressure.
7DO NOT operate the inflator when you are tired or under the influence of alcohol, drugs or intoxicating medication.
7DO NOT operate the inflator if any parts are missing or the inflator is damaged, as this may cause failure and/or personal
injury.
7DO NOT open the unit.
7DO NOT drive over hose or hose connector head.
3Keep hose tidy and restrained with the hook supplied when not in use.
SA3702 - 1 - 51104

DIGITAL TYRE INFLATOR
(WALL MOUNTED )
Model: SA3702
98/37/EC Machinery Directive
93/68/EEC Marking Directive
89/336 EEC EMC Directive
73.23/EEC Low Voltage Directive
www.sealey.co.uk
01284 757500 01284 703534 [e-mail]
Web email
Declaration of Conformity
The construction file for this product is held by the Manufacturer and
may be inspected, by a national authority, upon request to Jack
Sealey Ltd.
For Jack Sealey Ltd.
Sole importer into the UK
of Sealey Professional Tools.
Signed by
Mark Sweetman 4th November 2004
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and compo-
nent parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of this equipment. WARRANTY: Guarantee
is 12 months from purchase date, proof of which will be required for any claim. INFORMATION: For a copy of our latest cata-
logue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
5. MAINTENANCE
5.1 There is no requirement to service the following items:
Pressure Transducer
Electronic Control Board
5.2 Weekly
Check hose and tyre connector. If leaks are evident then replace, small leaks will be evident by constant refilling of
the tyre.
Annual
Disconnect air Input supply and tyre hose from the head. Unscrew captive sintered filters from filter housings and
clean or replace.
Fig 1
We, the sole importer into the UK, declare that the product listed here is in conformity with the
following standards and directives.
SA3702 - 1 - 51104