Sealey AUTO SERVICE VS720 User manual

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL
REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE
PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY
AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
INSTRUCTIONS FOR:
BUSH REPLACEMENT TOOL FOR
VAUXHALL/OPEL VECTRA
MODEL No: VS720
1.2 GENERAL SAFETY
WARNING! Ensure Health & Safety, local authority, and general
workshop practice regulations are adhered to when using this
tool.
WARNING! Familiarise yourself with the specific applications
and limitations of the bush replacement tool, as well as any
potential hazards.
This tool should be used in conjunction with inspection
maintenance
procedures recommended in the vehicle manufacturer’s manual.
Ensure that the bush replacement tool is the correct tool for the
task.
DO NOT use the bush replacement tool for any purpose other
than that for which it is designed.
Ensure that the vehicle is properly supported with axle stands
before working under the vehicle.
Ensure there is adequate lighting prior to using the bush
replacement tool. A range of inspection lamps is available from
your local Sealey dealer.
Keep children and unauthorised persons away from the working
area.
DO NOT use the bush replacement tool if any parts are damaged
or missing, as this may cause failure and/or personal injury.
DO NOT use the bush replacement tool when you are tired, or
under the influence of alcohol, drugs or intoxicating medication.
2.1. REMOVING A BUSH.
Refer to Fig.2:
2.1.1. Screw the threaded bar F into the bush removal cup Aand insert the threaded bar into the bush to be removed
from the vehicle rear trailing arm bush-mounting (Step one).
2.1.2. Locate components B, C, D and Eon threaded bar F(Step two).
2.1.3. Using a ring spanner, or ratchet wrench, tighten nut E(Step three) until the bush is clear of the vehicle rear trailing
arm and located in component B (Step four).
2.1.4. Remove the bush from component Bby unscrewing the bush removal cup A and components C, D and Efrom
the threaded bar F(Step 5).
2.1.5. Replace all the components comprising the bush replacement tool in the appropriate slots in the carrying case
(Fig.4).
Fig.1
Fig.2

ALWAYS KEEP FORCE (F) SCREW
WELL LUBRICATED.
DO NOT USE AIR TOOLS
1. SAFETY INSTRUCTIONS
2. OPERATING INSTRUCTIONS
VS720 Issue No. 3 - 23/08/11
Threaded rod maximum load 150Nm. Exceeding this load
will shorten the life of the threaded rod. The threaded
rod is considered to be a consumable item and is NOT
covered under warranty.
Original Language Version

3.1. REPLACING A BUSH
Refer to Fig.3:
3.1.1. Screw the threaded bar F into the bush insertion cup G. Hold the cup against the outer face of the trailing arm,
so that the threaded bar protrudes through the bush seating. Slide the bush on to the threaded bar F
(Step one).
3.1.2. Locate components H, D and Eon threaded bar F(Step two).
3.1.3. Using a ring spanner, or ratchet wrench, tighten nut E(Step three) until the bush is pressed into the vehicle rear
trailing arm.
3.1.4. Unscrew the bush insertion cup G. Remove the threaded bar Ffrom the bush mounting and components H, D
and Efrom the threaded bar F (Step four).
3.1.5. Replace all the components comprising the bush replacement tool in the appropriate slots in the carrying case
(Fig.4).
Fig.3
Fig.4
01284 757500
01284 703534
[e-mail]
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
www.sealey.co.uk
Web
email
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without
prior notice. IMPORTANT: No liability is accepted for incorrect use of product. WARRANTY: Guarantee is 12 months from purchase date, proof of
which will be required for any claim. INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave
your full name and address, including postcode.
VS720 Issue No. 3 - 23/08/11
Original Language Version