Sealey SA314.V2 User manual

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
1. SAFETY INSTRUCTIONS
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
2. INTRODUCTION & SPECIFICATION
INSTRUCTIONS FOR:
AIR RIVETER
MODEL No: SA314.V2
 WARNING! Ensure health & safety, local authority, and general workshop practice regulations are adhered to when using this equipment.
Familiarise yourself with this products application and limitations, as well as the specific potential hazards peculiar to the riveter.
 WARNING!Disconnect the riveter from the air supply before changing accessories, servicing or performing any maintenance.
Maintain the riveter in good condition (use an authorised service agent).
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
Use in a suitable work area. Keep area free from unrelated materials and ensure that there is adequate lighting.
Keep the riveter clean for best and safest performance.
WARNING! Always wear approved eye (or face) and hand protection when operating the riveter.
Maintain correct balance and footing. Do not over reach, ensure the floor is not slippery, wear non slip shoes.
Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery and contain or tie back long hair.
 Wear appropriate protective clothing and keep hands and body clear or working parts.
Keep the riveter away from your body and at a safe distance from others.
Keep children and unauthorised persons away from the working area.
Secure non stable work piece with a clamp, vice or other adequate holding device.
Ensure that spent rivet stems are disposed of correctly and do not cause a hazard.
WARNING! ensure correct air pressure is maintained and not exceeded. Recommended pressure 70-90psi.
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use, and ensure that all connections are secure.
 DO NOT use the riveter for a task it is not designed to perform.
 DO NOT operate the riveter if any parts are damaged or missing as this may cause failure and/or personal injury.
Ensure the safety bottle (part 15) is correctly fitted.
 DO NOT carry the by the hose, or yank the hose from the air supply.
 DO NOT get the riveter wet or use in damp/wet locations or areas where there is condensation.
 DO NOT allow untrained persons to operate the riveter.
 DO NOT operate the riveter when you are tired, under the influence of alcohol, drugs or intoxicating medication.
 DO NOT direct air from the air hose at yourself or others.
When not in use disconnect from the air supply and store in a safe, dry, child proof location.
 Avoid unintentional starting.
Suitable for aluminium, steel and stainless steel rivets up to 1/4”. Supplied with five riveting nozzles and
two spanners. Trigger operated riveter with hardened steel jaw assembly and rivet shaft safety cap. Will
handle heavy assembly work.
Nozzle Sizes: 3/32”(2.4mm), 1/8”(3.2mm) ......
5/32”(4.0mm), ...... 3/16”(4.8mm),1/4”(6.4mm)
Air Consumption: ..................4.5cfm
Operating Pressure: .................90psi
Air Inlet Size: .................... 1/4” BSP
Weight: ............................1.6kg
3. AIR SUPPLY
3.1. Air Supply
WARNING! Ensure the air supply is clean and does not exceed 90psi while operating the riveter. Too high an air pressure and unclean air
will cause excessive wear, and may be dangerous, causing damage and/or personal injury.
3.1.1. Ensure the riveter air valve (or trigger) is not depressed before connecting to the air supply.
3.1.2. You will require an air pressure between 70-90psi, and an air flow according to the specification above.
3.1.3. Drain the compressor daily. Water in the air line will damage the riveter and invalidate your warranty.
3.1.4. Clean air inlet filter weekly. Recommended hook-up procedure is shown in fig 1.
3.1.5. Line pressure should be increased to compensate for unusually long air hoses (over 8 metres).
The minimum hose diameter should be 1/4” I.D. and fittings must have the same inside dimensions.
3.1.6. Keep hose away from heat, oil and sharp edges. Check hoses for wear, and make certain that all connections are secure.
3.2. Couplings
Vibration may cause failure if a quick change coupling is connected directly to the air riveter. To overcome this, connect a leader
hose - Sealey model number AH2R or AH2R/38 - to the riveter. A quick change coupling may then be used to connect the leader hose
to the air line recoil hose. See figs.1 & 2.
Original Language Version SA314.V2 Issue: 2 - 08/12/09

WARNING! Ensure you have read, understood and applied the safety instructions. This Tool
is designed for riveting metal, primarily in workshops and garages. We do not recommend any
other use.
4.1. Filling with hydraulic oil: (Check each time before use).
4.1.1. Disconnect the tool from the air line.
4.1.2. Hold the tool upside-down and remove the air cylinder cap with a spanner.
4.1.3. Remove piston set.
4.1.4. Pump hydraulic oil into hydraulic cylinder until it overflows from the cylinder neck, (fig 3) and
wipe any excess oil away with a dry cloth.
4.1.5. Insert hydraulic plunger into cylinder and press it in slightly.
4.1.6. Reverse above procedure to reassemble. Slightly lubricate the inside wall of the air cylinder.
4.2. Adjusting the stroke:
4.2.1. Check that the hydraulic level is at its maximum (see 4.1).
4.2.2. Check the jaw stroke by using the supplied wrench/gauge as in fig.4, and adjust if necessary
(there is a 5mm tolerance).
4.2.3. Hold the jaw case in place with a spanner and loosen the lock nut with the spanner gauge
supplied. Adjust the distance between them as required.
4.2.4. Tighten the lock nut when adjustment is complete.
4.3. Changing Jaws:
4.3.1. Disconnect the tool from the air line.
4.3.2. Use a spanner to remove the frame head.
4.3.3. Use both spanners to unscrew the jaw case.
4.3.4. Remove the jaws and clean with solvent or a brush. If the teeth are blunted,
replace with new jaws. Use genuine Sealey parts only (part No. SA314.V2-04).
4.3.5. Reverse the above procedure to reassemble.
4.4. Operation:
4.4.1. Be sure to select the correct nosepiece and rivet for the job.
4.4.2. Insert the rivet into the nosepiece.
4.4.3. Direct the nosepiece at the pre-drilled hole and squeeze the trigger.
4. OPERATING INSTRUCTIONS
5. MAINTENANCE
WARNING! Ensure you disconnect the tool from the air supply system before attempting any service or maintenance.
5.1. Maintain the tool with care. Keep it oiled for optimum performance.
5.2. Lubricate the air tool daily with a high quality air tool oil, (Sealey model no. ATO/500 or ATO/1000).
5.3. Store the tool in a safe, dry, secure environment.
5.4. Factors that may inhibit performance.
Loss of power or erratic action may be caused by reduced compressor output, an excessive drain on the air line, moisture or
restrictions in air pipes or the use of hose connections of improper size. Grit or gum deposits in the tool may cut power and can be
corrected by cleaning the air strainer and flushing out the tool with gum solvent oil or an equivalent de-greaser. If all outside
conditions are in order, disconnect the tool from the air supply, disassemble and replace any worn or damaged parts with Sealey
original parts. Clean all parts, reassemble the tool and lubricate as described above. Alternatively, take the tool to your nearest
authorised service agent.
Note: Wrench/gauge design may differ from
above. See spare parts diagram.
Fig.1. Fig.2.
Fig.3.
Fig.4.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
[e-mail]
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Web
email
Original Language Version SA314.V2 Issue: 2 - 08/12/09

Issue Date:- 220506
Version No:- 1
PARTS FOR:
AIR RIVETER
MODEL No: SA314.V2
ITEM PART NO. DESCRIPTION
1A SA314.V2-01 NOSE PIECE 4.0mm (5/32")
1B SA314.V2-01.1 NOSE PIECE 4.8mm (3/16")
1C SA314.V2-01.2 NOSE PIECE 6.4mm (1/4")
1D SA314.V2-01.3 NOSE PIECE 2.4mm (3/32”)
1E SA314.V2-01.4 NOSE PIECE 3.2mm (1/8")
2 SA314.V2-02 CYLINDER
3 SA314.V2-03 JAW CARRIER
4 SA314.V2-04 JAWS (1SET = 3PCS)
5 SA314.V2-05 JAW PUSHER
6 SA314.V2-06 JAW PUSHER SPRING
7 SA314.V2-07 JAW CYLINDER
8 SA314.V2-08 LOCK NUT
9 SA314.V2-09 AXIS
10 SA314.V2-10 PLASTIC RING
11 SA314.V2-11 HANDLE
12 SA314.V2-12 AXIS
13 SA314.V2-13 RING
14 SA314.V2-14 SPRING
15 SA314.V2-15 BOTTLE
16 SA314.V2-16 LID
17 SA314.V2-17 BUSH
18 SA314.V2-18 LOCK NUT
19 SA314.V2-19 CYLINDER
20 SA314.V2-20 PISTON
21 SA314.V2-21 CUSHION
22 SA314.V2-22 PISTON
23 SA314.V2-23 NUT
24 SA314.V2-24 CYLINDER LID
ITEM PART NO. DESCRIPTION
25 SA314.V2-25 TRIGGER
26 SA314.V2-26 LINK
27 SA314.V2-27 CONNECTOR
28 SA314.V2-28 AIR VALVE
29 SA314.V2-29 VALVE SPRING
30 SA314.V2-30 COPPER WASHER
31 SA314.V2-31 VALVE COLLAR
32 SA314.V2-32 SPRING
33 SA314.V2-33 NUT
34 SA314.V2-34 BASE COVER
35 SA314.V2-B01 O-RING
36 SA314.V2-B02 O-RING
37 SA314.V2-B03 O-RING
38 SA314.V2-B04 O-RING
39 SA314.V2-B05 O-RING
40 SA314.V2-B06 SPRING PIN
41 SA314.V2-B07 SPRING PIN
42 SA314.V2-B08 SPRING PIN
43 SA314.V2-B09 SPRING PIN
44 SA314.V2-B10 O-RING
45 SA314.V2-B11 O-RING
46 SA314.V2-B12 O-RING
47 SA314.V2-B13 O-RING
48 SA314.V2-B14 O-RING
49 SA314.V2-B15 O-RING
50 SA314.V2-C01 AIR VALVE
51 SA314.V2C01-1 WRENCH
52 SA314.V2C01-2 WRENCH
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
[e-mail]
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Web
email