Sealey SCR91 User manual

MECHANIC’S DETAILING UTILITY SEAT
MODEL NO: SCR91
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this seat.
9Locate seat in a suitable working area.
WARNING! Use seat on level and solid ground, preferably concrete.
9Keep the seat clean and tidy in accordance with good workshop practice.
8DO NOT use the seat for any purpose other than that for which it is designed.
8DO NOT stand on the seat.
8DO NOT use the seat outdoors.
8DO NOT get the seat wet or use in damp or wet locations or areas where there is condensation.
8DO NOT clean the seat with any solvents which may damage the paint surface or the protective coating on the padded seat base.
8DO NOT use if damaged.
2. INTRODUCTION
Composite framework with concealed under seat. Suitable for use in Bodyshop and Detailing environments as well as general garage use.
Easy-rolling Ø100mm rubber castors with ball-bearing swivel. Supplied with six interchangeable cup/bottle holders and storage trays for
tools and components.
3. SPECIFICATION
Model No....................................................................SCR91
Overall Size (W x D x H) .........................990 x 470 x 400mm
4. CONTENTS
1 Seat Cover
2 Removable Drawer (Front)
3 Drawer Holder
4 Removable Tray (Side)
5 Frame
6 Steel Nut M10 Zinc
7 Castor Wheel Support
8 Hex Head Set Screw M10 X 40 Zinc
9 Removable Tray (Cup/Bottle Holder)
10 Steel Nut M10 Domed
11 Flat Washer M10 Zinc
12 Castor Wheel
5. ASSEMBLY
5.1. Fix Castor Wheel Supports (item 7) to Frame (item 5)
 usingxings(items6and8).
5.2. Fit Castors (item 12) to Castor Wheel Supports (item7) using nuts and washers (items 10 and 11).
5.3.  Locateremainingitemsintobodyasshowning.1.
6. MAINTENANCE
6.1.  Beforeeachuse,inspecttheoverallconditionoftheunitforbroken,crackedorbentpartsthatmaya󰀨ecttheproperoperation.
6.2. Regularly check the tightness of all fixings before use.
6.3. Smear the castor bearings with a thin film of silicone grease quarterly.
6.4. Ensure the castor wheels are able to rotate and swivel freely. Replace if necessary.
6.5. Clean the seat cushion, trays and frames with a moist cloth and mild detergent. DO NOT use solvents to clean the unit.
Refer to
instructions
SCR91 Issue 1 31/05/22
Original Language Version
© Jack Sealey Limited
Fig.1

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 [e-mail] www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
SCR91 Issue 1 31/05/22
Original Language Version
© Jack Sealey Limited
Parts support is available for this product. Please email [e-mail] or telephone [phone]