Sealey VS313 User manual

GLOW PLUG PULLER SET
MODEL NO: VS313
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING! Ensure Health and Safety, local authority and general workshop practice regulations are adhered to when using tools.
8DO NOT use tool if damaged.
9Maintain tool in good and clean condition for best and safest performance.
9Wear approved eye protection. A full range of personal safety equipment is available from your Sealey stockist.
9Wear suitable clothing to avoid snagging. DO NOT wear jewellery and tie back long hair.
8DO NOT attempt to start engine or move vehicle, whilst tools are fitted and work is in progress.
9Ensure any disconnected fuel pipes are plugged to avoid spillage.
9Account for all tools and parts being used, DO NOT leave them in or near the engine. Return all parts to the case and store this in a safe,
dry, childproof location.
IMPORTANT: These instructions are provided as a guide only. Always refer to the vehicle manufacturer’s service instructions, or a
proprietary manual, to establish the current procedure and data.
WARNING! The warnings referred to in this guide cannot cover all possible conditions and situations that may occur. It must be
understood that common sense and caution are factors which cannot be built into this product, but must be applied by the operator.
2. INTRODUCTION
Acomprehensive set suitable for removing stubborn glow plugs. Ideal for removing plugs that have been unscrewed, but seized, due to
residue build-up or where the lament has been distorted. Quick and e󰀨ective method, saving time and money. Supplied in storage case.
3. SPECIFICATION
Model no ..................................................................... VS313
External clamping collets ....................... 2.7, 3.6, 5(x2), 6mm
4. OPERATION
Note: Ensure the glow plug has been fully unscrewed from the cylinder head, if not damage to the threads in the cylinder head may
occur.
4.1. Take the correct sized glow plug collet (g.1.4) and insert it through the appropriately sized sleeve (g.1.1). Ensure the ange on the
sleeve is the same side as the thread on the collet.
  Note:Theglowplugmaynottakeanexternalcollectbuthastheinternalrecesstoaccepttheinternalcollet(g.1.2).
4.2. Screw the collet into the tool (g.1.3, screw back the pressure screw (g.3) to allow the collet to be screwed fully home.
4.3. Insert the collet over the end of the glow plug or inside the glow plug (dependant on the type of collet needed).
4.4. Screw down the pressure screw so the collet tightens securely to the glow plug.
Refer to
instruction
manual
Wear eye
protection
VS313 Issue:3 ( H,F) 11/09/20
Original Language Version
© Jack Sealey Limited
fig.2
fig.1

4.5. Use the slide hammer (g.3) to gradually remove the seized glow plug.
4.6. If the glow plug cannot be removed, it may be necessary to use a suitable penetrating oil and leave for a period of time to assist the
removal.
4.7. If the glow plug still cannot be removed, consult a main dealer or diesel specialist, to avoid damage to the engine.
.
fig.3
Original Language Version
© Jack Sealey Limited VS313 Issue:3 ( H,F) 11/09/20
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 [e-mail] www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.