Sealey PT2200.V2 User manual

1150 X 550MM PALLET TRUCK
2200KG CAPACITY
MODEL NO: PT2200.V2
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURYAND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
8DO NOT use a faulty or damaged pallet truck.
9Before using the pallet truck, all parts and working mechanisms should be checked for wear or damage. Pay particular attention to the
wheels, handle, fork lifting and lowering mechanism. Any parts found to be worn, damaged or suspect should be repaired or replaced
before the truck is used.
9All repairs must be carried out by an authorised Sealey service agent.
9Personnel who operate the pallet truck and those in the vicinity of operation should wear safety footwear at all times.
9Never place any part of your body in the lifting mechanism or under the forks or load.
8DO NOT allow others to ride on the pallet truck.
8DO NOT lift or move unstable or loosely stacked loads.
9 Takespecialcarewhenmovinglong,highorwideloadsinordernottodislodgetheloadbystrikinganystructures,permanentxtures,
vehicles or people in the area of operation.
9Always ensure load is evenly distributed across forks with the centre of the load being at the halfway point of the length of the forks.
8DO NOToverloadthepallettruck-refertothespecicationformaximumpermittedload.
9If a load is left unattended or if not in use (even for a very short period of time) it should be lowered to the ground.
9Ensure that the width and length of the forks is correct for the pallet to be lifted.
9 Ensurethatthepallettruckissu󰀩cientlyinsertedintothepallettoliftthefulldepthofthepallet.
9 Usethepallettruckonlevel,at,hardsurfaces.
9The operator of the pallet truck must be physically capable of controlling the load selected; particularly in relation to stopping a rolling
load.
9When the pallet truck is not in use, lower the forks and park it where it will not be a hazard.
9The pallet truck is designed for indoor use +5°C and +40°C.
8DO NOT use on sloping or uneven ground and do not attempt to negotiate curbs, steps or ramps.
2. INTRODUCTION
Heavy-duty truck suitable for warehouse and general handling duties. Polyurethane, non-marking wheels and tandem loading rollers with sealed-
for-life bearings all round. Robust and durable galvanized hydraulic unit with chromed ram and piston for resistance to corrosion.
3. SPECIFICATIONs
Capacity ........................................................................2200kg
Minimum height...............................................................85mm
Maximumheight ............................................................200mm
Forks(lengthxoverallwidth) ............................1150x550mm
Fork spread...................................................................230mm
4. ASSEMBLY
4.1. Take the handle and thread the pin and chain through the aperture
(fig.1.1) in the cross shaft.
4.2. Place the handle base on the pump bracket and secure by screwing the
 hexheadedscrewsintotappedholes(figs.1.2,1.3and1.4.)
4.3. Ensure that the control lever is in its lowest (raise) position.
4.4. Looking below the pump bracket, raise the valve fork (fig.2.1) and
engage the head of the pin (fig.2.2) into the fork.
4.5. Release the valve fork, which will engage with the head of the pin.
5. OPERATION
5.1. Before using the truck read and understand the safety instructions in Section 1.
5.2. The truck should only be operated by those persons who have been trained in its use.
5.3. The operator must be physically capable of pushing or pulling the load and must also be
capable of stopping a rolling load.
Refer to
instruction
manual
Wear safety
footwear
fig.1
PT2200.V2 Issue:1 28/09/21
Original Language Version
© Jack Sealey Limited

5.4. Before lifting any load the operator should check that the pallet is the correct width and
length for the truck and that the pallet itself is not damaged.
5.5. The operator should ensure that the load on the pallet is safe to move. If the load appears
to be loosely stacked, unevenly distributed, too high or too wide it should be repacked safely
before moving. Also check that the weight of the load is within the capacity of the truck.
5.6. Lowering the truck. (Seeg.3-L)
Before inserting the truck into the pallet ensure that the truck forks are in their lowest position by pulling the operating lever into the
upper (lowering) position and holding it until the truck has settled to the lowest level.
5.7. Drive position. (Seeg.3-D)
The lever can now be released and will return to the middle (drive) position.
Push the truck into the pallet ensuring that the forks are fully inserted. If the pallet is shorter than the forks the load should be placed at
the centre point of the length of the forks.
5.8. Raising a load. (Seeg.3-R)Pushtheoperatinglevertoitslowest(raise)positionwhereitwilllatch.Pumpthehandletolifttheload.
Return the operating lever to its neutral (drive) position before moving the truck.
5.9. Due care should be taken when manoeuvring a load to ensure that no collision takes place with any objects or people.
5.10. Thefasterthetruckismovedthemoredi󰀩cultitwillbetostop:proceedataslowandevenpace.
5.11. Bringthetrucktoastopwhererequiredandlowertheloadtotheoorbypullingtheoperatinglevertoitshighestposition 
 andholdingitthereuntiltheloadhassettledtotheoor.
5.12. It is not recommended that the load is lowered whilst the truck is still moving as a sudden stop may dislodge the load causing
possible damage to property and/or people.
6. MAINTENANCE
6.1. The oil level should be checked every 6 months.
6.1.1. Check the oil with the forks lowered fully.
6.1.2. To check the oil level, remove the reservoir cover by removing the screw on either side (Fig.4).
6.1.3. Removethecapfromthereservoir(g.5)andtopupifnecessary.
6.1.4. Replace the cap and the cover.
6.1.5. To purge air from the system hold the operating lever in the lowering position until the truck has descended to its lowest level then
pump the handle 8 to 10 times.
6.2. Apply a long life grease to all bearings and shafts once a month.
fig.2
fig.3
Best practice:
fig.4 fig.5
Original Language Version
© Jack Sealey Limited PT2200.V2 Issue:1 28/09/21

7. TROUBLESHOOTING
THE PROBLEM THE CAUSE THE SOLUTION
Theforksdonotreachmaximum
height. Hydraulic oil level too low. Too cold. Top up the oil. Operate at rated temperature.
The forks do not raise. No hydraulic oil Fill with hydraulic oil
The oil is contaminated. Change the oil.
Air in the hydraulic system. Purge the air as described in Section 6.
The forks will not descend Truck stored in raised position allowing
exposedpistonrodtocorrodeandjam. Lubricate rod regularly and store truck in lowered position.
Piston rod or pump body deformed as a result
of overloading or unbalanced load. Replace piston rod or pump body.
Leaks. Seals worn, damaged or cracked. Replace seals.
The forks descend and cannot be
maintained in the raised position. Release valve not fully closed owing to impurities in oil. Change the oil.
Air in the hydraulic system. Purge the air as described in Section 6.
Seals worn, damaged or cracked. Replace seals.
Parts of hydraulic system cracked or worn. Inspect and replace.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 [e-mail] www.sealey.co.uk
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Original Language Version
© Jack Sealey Limited PT2200.V2 Issue:1 28/09/21