SECO-LARM E-931-S33PRQ User manual

ENFORCER 33ft Polarized
Reflective Photoelectric Beam Sensor
4 SECO-
LARM U.S.A., Inc.
WARRANTY
This SECO
-
L RM product is warranted against defects in material and wo
rkmanship while used in normal service
for a period of one (1) year from the date of sale to the original consumer customer. SECO-
L RM’s obligation is limited to the
repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO
-
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, r
or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-
L RM d
equipment is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-
L RM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at
SECO-L RM’s option. In no event shall SECO-
L RM be liable for any special, collateral, incidental, or consequential personal
or property damages of any kind to the purchaser or anyone else.
NOTICE:
The information and specifications printed in this manual a
re current at the time of publication. However, the
SECO-L RM policy is one of continual development and improvement. For this reason, SECO-
L RM reserves the right to
change specifications without notice. SECO-L RM is also not responsible for misprints
or typographical errors.
Copyright © 2013 SECO-
L RM U.S. ., Inc. ll rights reserved. This material may not be reproduced or copied, in whole or in
part, without the written permission of SECO-L RM.
SECO
SECOSECO
SECO
-
--
-
LARM
LARMLARM
LARM
®
U.S.A., Inc.
16842 Millikan venue, Irvine, C 92606 Website: www.seco-larm.com
Tel: [phone] Fax: [phone] E-mail: [e-mail]
Troubleshootin :
Sensor does not detect the object.
•
Change the angle of the sensor or readjust
the sensitivity setting.
The
beam sensor LED will not turn green.
•
Clean the sensor and reflector with a damp
(not wet) cloth.
•
djust the reflector and/or sensor for proper
alignment.
Beam sensor LED lights when object
is detected, but there is no output.
•
Check wiring between the sensor and local
alarm device.
Sample Applications:
Gara e
Door
Gate
Vehicle
Detection
Other Sensors Available:
Dual and
Quad Beam
Optional Accessory:
Reflector Hood
E-931 CC-HR
Provides extra
protection for the
reflector.
Compatible with Reflective Photoelectric Beam Sensor models
E-931-S50RR , E-931-S35RR , and E-931-S33PR .
Reflective
Photobeam
Reflective Photoelectric Beam Sensor
LARM U.S.A., Inc.
rkmanship while used in normal service
L RM’s obligation is limited to the
-
L RM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, r
epair,
L RM d
etermines that such
equipment is not operating properly as a result of causes other than defects in material and workmanship.
L RM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at
L RM be liable for any special, collateral, incidental, or consequential personal
re current at the time of publication. However, the
L RM reserves the right to
or typographical errors.
L RM U.S. ., Inc. ll rights reserved. This material may not be reproduced or copied, in whole or in
MiE
-
931
-
S
33P
RQ_1
301
.docx
PITSW3
Change the angle of the sensor or readjust
the sensitivity setting.
Clean the sensor and reflector with a damp
djust the reflector and/or sensor for proper
Check wiring between the sensor and local
Assembly
Line
Other Sensors Available:
Dual and
Quad Beam
Curtain and
Barrier
E-931-S33PRQ
33
ft
Polarized
Reflective
Photoelectric Beam
Sensor
Note: Products with model numbers that end with “Q” or that have a round green “Q” sticker are RoHS compliant.
Manual
•
Polarized sensor is immune to
•shiny objects: Triggers only when
•correctly reflected light is detected.
•Weatherproof (IP66)
•nti-condensation housing
•Input voltage 12~250 V C/VDC
•
Up to 33ft (10m) sensing range
•Round reflector, Dia.: 82 mm.
•Form C relay: 1 @30VDC
•Beam status LED
•N.C. Tamper switch:
500m @30VDC
Caution:
•This sensor is not designed to prevent bodily injury or loss of life.
•This sensor is not designed for use in environments where explosive gasses may be present.
•Use of this sensor in certain security applications may be regulated by local laws or codes. SECO-L RM is not
responsible for compliance with such laws or codes.

ENFORCER 33ft Polarized Reflective Photoelectric Beam Sensor
2 SECO-LARM U.S.A., Inc.
Specifications:
Model
E
-
931
-
S
33P
RQ
Type
Polarized r
eflective
photoelectric beam sensor
Sensin
ran e
33
ft (1
0
m)
Operatin volta e
12~2
5
0 V C/VDC
Current draw (max.)
12VDC
Standby:
20
m
; ctive:
40
m
24VAC
Standby:
1
0m
; ctive:
20
m
Response time
10ms
(max.)
Li ht source
IR LED
/Wavelength 740nm
LEDs
Solid
Green
Good beam signal, properly
aligned
Alternatin flash
Poor beam signal
Solid
Red
No beam signal, triggered
Tri er output
SPDT Relay output (NO/NC/COM)
Switchin capacity
0.5 @120V C/1 @30VDC
Tamper switch
N.C.,
500m @30VDC
IP Ratin
IP66
Operatin temperature -4
°
~131
°
F (-20
°
~55
°
C)
Parts List:
1x Sensor
1x Reflector
1x Mounting bracket
1x Sensor hood
4x Cover screws
2x Mounting screws
1x Reflector mounting screw
1x Rubber ring
1x Cable connector
1x Manual
1x Removable terminal block
Overview:
Tamper switch
Vertical
adjustment screw
(without cover)
Cover
Cover
screw
Wire cable
connector
Mounting plate
Hood
Dimensions:
Beam
sensor LED
Terminal
block
Cable breakout
Captive screw
Beam sensor
4
13
/
16
”
(122mm)
3
/
16
”
(4mm)
3
7
/
32
”
(82mm)
11
/
32
”
(9mm)
2
1
/
8
”
(54mm)
2
3
/
8
”
(60mm)
1
15
/
16
”
(49mm)
2
7
/
16
”
(62mm)
Cable breakout
•
Polarity does not matter for the power input.
•Connect the N.C. tamper terminal to the
tamper circuit of an alarm control panel.
Wirin Dia ram:
12~250
V C/VDC
(Non-Polarity) N.C.
N.O. COM
Tamper
N.C.
Relay
ENFORCER 33ft Polarized Reflective Photoelectric Beam Sensor
SECO-LARM U.S.A., Inc. 3
1.
Mount the sensor
and reflector so that they face
each other.
2. Connect power to the sensor. The LED will light as
indicated in the chart below.
3. Unscrew the 4 cover screws and remove the cover.
4. To find the correct alignment, slowly turn the lens
assembly left and right to adjust the horizontal angle.
5. Loosen the vertical adjustment screw to adjust the
vertical angle.
6. Place the hood on the sensor by sliding the hood’s
ridges into the slots on the sides of the sensor.
7. Re-attach the cover, replace the four screws, and
attach the hood to the top of the sensor.
1.
Unscrew the
four
cover screws and remove the cover.
2. Loosen the captive screw and remove the sensor
from the mounting plate.
3. Using the included mounting screws, mount the
mounting plate to the wall.
4. Use the cable breakout and cable connector at
the bottom or rear of the sensor to run the wires.
5. Hang the sensor back on the plate and use the captive screw to secure it in place.
6. Re-attach the cover, replace the four screws, and attach the hood to the top of the sensor.
Mountin :
Ali nment:
Solid green
Good beam signal,
properly aligned
lternating flash
Poor beam signal
Solid red
No beam signal,
triggered
Lens
alignment
±90
°
±5°
Horizontal
adjustment
Vertical
adjustment
Wirin for the Rear Cable Breakout
1.
Puncture the cable breakout located at the rear of
the sensor using a screwdriver or other object.
2. Run wires through the included rubber ring.
3. Install the weatherproofing ring with the wires already
installed in the cable breakout hole.
4. Make sure the ring is secure and there is no room for
water to get into the unit.
Rubber
ring
Cable
breakout
Wirin for the Bottom Cable Breakout
1.
Puncture the cable breakout located at the bottom of
the sensor using a screwdriver or other object.
2. Insert the short end side of the cable connector
into the cable breakout hole and use the nut to
secure it, tightening with a wrench as needed.
3. Run the wires through the end cap and cable connector.
4. Then screw the end cap into the external side of the cable
connector to prevent water from entering the unit.
Cable
Connector
End cap
Sensor
Nut
Rubber
neck