SECO-LARM ENFORCER CS-PD535-TAQ User manual

Features
:
Installation:
Infrared Proximity Sensor
Manual
1.
The sensor is meant to be installed on a rigid thin surface,
maximum thickness 1/16" (2mm).
2. Use the mounting template to mark and cut holes in the
mounting surface. Disassemble the sensor for installation.
3. Install the sensor as illustrated below except for the back cover
.
4. Punch through the wiring grommet to thread the wires through
and connect them to the terminal block.
5. To reverse the LED colors for standby and activated, remove
the jumper pin (see Fig. 1).
6. To adjust the sensor's range, turn the trimpot counterclockwise
(decrease) or clockwise (increase) (see Fig. 1).
7. To adjust the output time, turn the trimpot counterclockwise
(decrease) or clockwise (increase). To set to toggle, turn the
trimpot all the way counterclockwise (see Fig. 1).
8. Install the back cover.
 No-touch operation reduces the risk of
spread of germs, viruses, etc., through
cross-contamination
 Adjustable sensor range 23/8"-8" (6~20 cm),
3A relay, adjustable trigger duration 0.5~30
seconds or toggle
 LED illuminated sensor area for easy
identification
 Selectable LED colors (CS-PD535-TAQ
turns from red to green or green to red,
CS-PD535-TBQ turns from blue to green or
green to blue) when the sensor is activated
CS
-
PD535
-
TAQ shown
Model LED Colors
CS-PD535-TAQ Green/Red
CS-PD535-TBQ Green/Blue
– + COM NO NC
Fig. 1
Faceplate
mounting screws x4
Alignment
pin
Rear cover
mounting screws x4
Motherboard
mounting screws x2
Wiring grommet
Terminal block
Alignment
slot
Mounting surface
max
.
1
/
16
" (2mm)
Overview:
LED
Indicator
Sensor
LED Color jumper
Output time
trimpot
Sensor range
trimpot
Power
input
Relay
output

ENFORCER Infrared Proximity Sensor
2 SECO-LARM U.S.A., Inc.
Specifications:
Model
CS
-
PD535
-
TAQ
CS
-
PD535
-
TBQ
Operating voltage
12~24 VAC/VDC
Current draw (max.)
120mA@12VDC
Relay type
Form C dry contact, 3A@24VDC
Connectors
Quick
-
connect, screwless terminal block
Response time
10ms
Output time
Adjustable, 0.5~30 sec., toggle, or as long as sensor is triggered
Sensing range
Adjustable, 2
3
/
8
"~8" (6
-
20 cm)
LED
Indicators
Standby
Red*
Blue*
Triggered
Green*
Green*
Operating
life
Relay
500,000 cycles
Sensor
100,000 hours
Case material
ABS Plastic
Operating temperature
-
4°~131° F (
-
20°~55° C)
Dimensions
1
3
/
4
"x2
1
/
8
"x1
7
/
16
" (44x55x37 mm)
*Default, reversible by jumper
Dimensions:
P
IC
PN3
MI_CS-PD535-TxQ_200930.docx
SECO-LARM
® U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website:
www.seco
-
larm.com
Phone: [phone] | [phone] Email: [e-mail]
NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-
LARM reserves
the right to change specifications without notice. SECO-LARM is also not responsible for misprints.
All trademarks are the
property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2020 SECO-LARM U.S.A.,
Inc. All rights
reserved.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while
used in normal
service for one (1) year from the date of sale to the original customer.
IMPORTANT WARNING: For a weather-
resistant installation, ensure that the unit is installed in a waterproof back box, and
that the faceplate and faceplate screws are properly sealed. Incorrect mounting may lead to exposure to rain or moisture in
the enclosure which could cause a d
angerous electric shock, damage the device, and void the warranty. Users and installers
are responsible for ensuring that this product is properly installed and sealed.
IMPORTANT: Users and installers of this product are responsible for ensuring that
the installation and configuration of this
product complies with all national, state, and local laws and codes related to locking and egress devices. SECO-
LARM will
not be held responsible for the use of this product in violation of any current laws or codes.
17/16"
(
37
mm)
2"
(50
mm)
11/4"
(32mm)
21/8"
(55mm)
13/4"
(
44
mm)
111/16"
(43
mm)
11/8"
(29mm)
5/16"
(8
mm)