SECO-LARM SLI SD-997B-1SQ User manual

®
SD-997B-1SQ
Mini Surface-Mount Deadbolt
Manual
Features:
•
Fail-safe operation (unlocks if power is lost)
•Surface-mount design for easy installation
•Magnetic switch senses door position for
positive locking
•luminum alloy bolt,
15
/
32
" (12.7mm)
diameter,
9
/
16
" (14mm) throw
•utomatically relocks 6 seconds after the
lock is unlocked if the door is not opened
•
Door open/close monitor (NC/COM)
•Lock delay timer adjustable between 0
and 3 seconds
•Use with an optional digital keypad for
high security without a key
•Powered by a solenoid
•Status LED indicates when the lock is
engaged

SECO-LARM Mini Surface-Mount Deadbolt
2SECO-LARM U.S.A., Inc.
The SECO
-
L RM Mini Surface
-
Mount Electric Deadbolt is designed for hollow metal door
frames and solid
wooden door frames. Its small size makes it easy to add secure, electrical locking to small doors.
1x
Lock body
1x
5
-
pin connector
2x
Plate spacers
1x
Strike body
6x
Mounting screws (M4x45
mm)
6x
Screw cover stickers
1x
Manual
Operation Fail-Safe
Operating voltage 12VDC
Current draw Standby 237m @12VDC max.
ctive 650m @12VDC max.
Status sensor 250m @30VDC (NC/COM)
djustable delay timer 0/3 secs.
Operating temperature 32°~158° F (0°~70° C)
Weight 1-lb 2.5-oz (450g)
Specifications:
Introduction:
Parts List:
Installation:
Overvie :
13
/
16
"
(20mm)
1.
Determine where the deadbolt will be mounted (see
Possible Mounting Locations, pg. 3
).
2. djust the wire output direction and lock delay time based on the selected application (see djusting the
Lock Delay Time / Wire Output Direction, pg. 3).
Adjust the ire output direction:
a. Unscrew the two lock body screws and remove the cover of the lock body
b. Remove the wire grommet from the lock body and insert the wires of the 5-pin connector into the
grommet.
c. Plug the 5-pin male connector into the 5-pin socket and adjust the desired wire output direction.
Adjust the lock delay time:
a. The default lock delay time is 3 seconds. To remove the delay time, remove the jumper.
3. Use the screw holes of the lock body and strike body as templates and mark the locations of the screws
with a pencil.
4. Secure the lock body and strike body with the six included screws. Use four screws for the lock body and
two screws for the strike body. Cover the screw heads with the provided screw cover stickers.
NOTE: If there is a gap between the lock body and the strike body, use the included plate spacers to
correct the alignment (see Using the Plate Spacers, pg. 3).
4
1
/
2
"
(114mm)
4
1
/
2
"
(114mm)
4
1
/
2
"
(114mm)
1
9
/
16
"
(39mm)
9
/
16
"
(14mm)
1
/
16
"
(1mm)
1
1
/
16
"
(27mm)
13
/
16
"
(20mm)
Status
LED
ø
15
/
32
"
(ø
12.7mm)
Bolt
Lock Body Strike Body Plate Spacer
1
1
/
16
"
(27mm)
Door
Monitor
Magnet

SECO-LARM Mini Surface-Mount Deadbolt
SECO-LARM U.S.A., Inc. 3
Installation
(continued)
:
Adjusting the Lock Delay Time / Wire Output Direction
:
Possible Mounting Locations:
Using the Plate Spacers:
5.
Connect the w
ires and insulate them (see Wiring Diagram below
).
a. Red – Power input (+)
b. Brown – Power input (–)
c. Green – Control wire (–) ground to release bolt
d. Blue – Door monitor, COM
e. Purple – Door monitor, N.C. (active when door closed) ø
WARNING:
•Correct polarity of the red and brown wires is critical. Incorrect polarity will burn out the solenoid.
•Do not connect a voltage input on the green wire otherwise it will damage the unit.
•Maximum distance between lock body and strike body must not exceed 1/4" (6mm).
Jumper
Delay Time
ON
3s (default)
OFF
0s
5-pin Socket
Place spacer
Lock body Strike body
Lock delay jumper
djust wire grommet for
different wire output direction
5-Pin Connector
Vertical mount Horizontal mount
Wiring
Diagram
:
12VDC
Power
Supply
Red wire (+)
Green wire (control)
Brown wire (–)
Request
-
to
-
Exit
pushbutton
Card reader
or keypad
Blue wire (door monitor, COM) – manual lock/unlock
Purple wire (door monitor, N.C.) – active if door is locked
N.C.
COM
N.O.
(–)
(
+
)

SECO-LARM Mini Surface-Mount Deadbolt
4SECO-LARM U.S.A., Inc.
Deadbolt does not activate when the door
closes
•Make sure the sensor in the lock body is not too far from
the magnet in the strike body
•djust the strike body or lock body positioning
•Use the included shims to bring the lock body and strike
body closer together
Deadbolt activates when the door is closed,
but does not lock the door
•Make sure the deadbolt is going into the strike body
properly
How to reset the unit •Ground the green wire momentarily
Troubleshooting:
SECO-LARM
®
U.S.A., Inc.
16842 Millikan venue, Irvine, C 92606
Website:
www.seco
-
larm.com
Phone: (949) 261
-
2999 | (800) 662
-
0800
Email: sales@seco
-
larm.com
®
PITSW2
MI_SD
-
997B
-
1SQ_210323.docx
NOTICE
:
The SECO
-
L RM policy
is one of continual development and improvement. For that reason, SECO
-
L RM
reserves the right to change specifications without notice. SECO-L RM is also not responsible for misprints. ll t
rademarks
are the property of SECO-L RM U.S. ., Inc. or their respective owners. Copyright © 2021 SECO-L RM U.S. .,
Inc. ll
rights reserved.
WARRANTY:
This SECO
-
L
RM product is warranted against defects in material and workmanship while
used in normal
service for one (1) year from the date of sale to the original customer. SECO-
L RM’s obligation is limited to the repair or
replacement of any defective part if the unit is returned, transportation prepaid, to SECO-L RM.
This Warranty is void if
damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration,
improper or abnormal usage, or faulty installation, or if for any other reason SECO-
L RM determines that such equipment
is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of
SECO-L RM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-L RM
’s
option. In no event shall SECO-
L RM be liable for any special, collateral, incidental, or consequential personal or property
damage of any kind to the purchaser or anyone else.
IMPORTANT
:
Users and installers of this product are responsible for ensuring this product complies
with all national,
state, and local laws and statutes related to monitoring and recording audio and video signals. SECO-L RM
will not be
held responsible for the use of this product in violation of any current laws or statutes.
California Proposition 65 Warning:
These products may contain chemicals which are known to the State of California to
cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.