Secura QLF215 User manual

QLF 215 INSTRUCTION MANUAL
We’ll Make It Stress-Free
If you have any questions along the way, just give us a call.
1-800-359-5520. We’re ready to help!

2
IMPORTANT SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS – PLEASE READ ENTIRE MANUAL PRIOR TO USE
1 Does your TV weigh more than 100 lbs. (45.3 kg) including accessories?
No — Perfect!
Yes
— This mount is NOT compatible. Visit secura-av.com or call 1-800-359-5520 (UK: 0800-056-2853) to find a compatible mount.
2 What is
your wall
made of?
3 Do you
have all
the tools
needed?
4 Ready to begin?
Please read through these instructions completely to be sure you’re comfortable with this easy install process. Also check your TV owner’s manual to
see if there are any special requirements for mounting your TV.
If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of this product, contact Customer
Service at 1-800-359-5520 (UK: 0800-056-2853).
CAUTION: Avoid potential personal injuries and property damage!
ƕThis product is designed for use in wood stud, solid concrete, and concrete block walls - DO NOT install into drywall alone
ƕThe wall must be capable of supporting five times the weight of the TV and mount combined
ƕDo not use this product for any purpose not explicitly specified by manufacturer
ƕManufacturer is not responsible for damage or injury caused by incorrect assembly or use
100 lbs.
(45.3 kg)
Solid concrete
or concrete
block?
Perfect!
Drywall with
wood studs?
Perfect!
CAUTION:
DO NOT
install into
drywall alone
Unsure?
Call Customer Service:
1-888-333-9952
(UK: 0800-056-2853)
?
Wood Stud Install
Concrete Install
Tape
Measure Pencil Level Screw
driver
Electric
Drill
Socket
Wrench
Stud
Finder Awl Wood
Drill Bit
Masonry
Drill Bit Hammer
3/8 in.
(10 mm)
1/2 in.
(13 mm) 7/32 in.
(5.5 mm)
Before getting started, let’s make sure this mount is perfect for you!

3
Dimensions in. [mm]
TV INTERFACE
WALL PLATE
FULLY ASSEMBLED MOUNT
TOP VIEW - EXTENDED
TOP VIEW - RETRACTED
SIDE VIEW - EXTENDED
SIDE VIEW - RETRACTED
3-D
40mm
1.57in
400mm
15.75in
100mm
3.94in
600mm
23.62in
222mm
8.74in
435mm
17.13in
130mm
5.12in
422mm
16.61in
226mm
8.89in
408mm
16.06in
158mm
6.22in
420mm
16.53in
635mm
25.00in
3deg
3deg
ESTIMATED 55" TV
30deg 30deg
97mm
3.81in
5deg
15deg
377mm
14.84in

4
M6 x 12mm M6 x 35mm
M8 x 16mm M8 x 35mm
M8 x 20mm
M6 / M8
NOTE: Not all hardware included will be used.
WARNING: This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to
your dealer; contact Customer Service. Never use damaged parts!
Supplied Parts and Hardware
STEP 1 Parts and Hardware
TV Bracket
TV Screws
Washers
Spacers
22mm
02 x4
03 x4
04 x4
06 x4
05 x4
07 x4
08 x4
01 x2

5
STEP 3 Hardware Adjustments
STEP 2 Parts and Hardware
.695 x .350 x.075 in.
5/16 x 2¾ in.
M5 x 30mm
UX10 x 60R
4mm
Concrete Anchor
For concrete installations ONLY
CAUTION: Do not use in drywall or wood
12
x4
Locking Screw Hex Key
Wall Plate Assembly
Lag Bolts
Lag Bolt Washers
11 x4
10 x4
09 x1
13 x2 14 x1

6
Standard configurations
are shown. For special
applications, or if you
are uncertain about your
hardware selection,
contact Customer Service
at 1-800-359-5520.
M6
M8
1.1 Screw Diameter 1.2 Determine Spacers and Screw Length
a:Use no spacers for:
Flat back TVs (AND TV
closer to the wall).
ab
CAUTION: Verify adequate
thread engagement with your
screw/washer/spacer combination
AND TV bracket.(STEP 1.3)
- Too short will not hold the TV.
- Too long will damage the TV.
03
Too Short Too Long
Correct
b:Spacers supplied for:
ƕRound (irregular) back TVs
ƕExtra space needed (for cables
or inset mounting holes)
FLAT BACK ROUND BACK CABLES INSET HOLES
STEP 1 Attach Brackets to TV
Hand thread screws into
the threaded inserts on the
back of your TV to determine
which screw diameter (M6,
or M8) to use.

7
1.3 Attach TV Brackets
Ensure that your brackets are level and centered as much as possible on the back of the TV.
CAUTION: Avoid potential personal injuries and property damage! DO NOT use power tools for this step. Tighten the screws only enough
to secure the TV bracket to the TV. DO NOT overtighten the screws.
IMPORTANT: Ensure TV bracket is securely fastened before moving on to the next step.
aFlat Back
bRound Back / Extra Space
04 05
07
06
08
02
02
03
03
01

8
STEP 2A Wood Stud Option
CAUTION: Avoid potential personal injuries and property damage!
ƕDrywall covering the wall must not exceed 5/8 in. (16 mm)
ƕMinimum wood stud size: common 2 x 4 in. (51 x 102 mm) nominal 1½ x 3½ in. (38 x 89 mm)
ƕMinimum horizontal space between fasteners: 16 in. (406 mm)
ƕStud center must be verified
1. Locate your stud. Verify and mark the center of the stud by finding the stud edges using an awl, a thin nail, or an edge to edge stud finder.
2. Position the wall plate assembly 09 at your desired height and line up the holes with your stud center line. Level the wall plate assembly 09
and mark the four hole locations.
2
1
Max.
5/8 in. (16 mm) Min.
16 in. (406 mm)
09

9
3. Drill the four pilot holes using a 7/32 in. (5.5 mm) diameter drill bit.
IMPORTANT: Pilot holes must be drilled to a depth of 2 ¾ in. (70 mm). Be sure you mark and drill into the center of the stud.
4. Install wall plate assembly 09 . Tighten lag bolts 11 only until the washers 10 are pulled firmly against the wall plate assembly 09 .
CAUTION: Improper use could reduce the holding power of the lag bolt. To avoid potential injuries or property damage Do not over-
tighten the lag bolts
p
p
p
p
p
p
p
p
p
p
p
p
p
p
p
p
p
p
11 .
4
3
2 ¾in. (70 mm)
7/32 in.
(5.5 mm)
09
10
11
UP ARROW

10
Solid Concrete or Concrete Block Option
CAUTION: Avoid potential personal injuries and property damage!
ƕMount the wall plate assembly 09 directly onto the concrete surface
ƕMinimum solid concrete thickness: 8 in. (203 mm)
ƕMinimum concrete block size: 8 x 8x 16 in. (203 x 203 x 406 mm)
ƕMinimum horizontal space between fasteners: 16 in. (406 mm)
1. Position the wall plate 09 on the wall at your desired height. Level the wall plate 09 and mark the hole locations.
2. Drill four pilot holes using a 3/8 in. (10 mm) diameter masonry drill bit.
IMPORTANT: Pilot holes must be drilled to a depth of 3 in. (75 mm). Never drill into the mortar between blocks.
STEP 2B
12
3/8 in.
(10 mm)
3 in. (75 mm)
09