Securam SCANLOGIC FPC-1808-II-MB User manual

SECURAM® SCANLOGIC™
BIOMETRIC ELECTRONIC LOCK
Model FPC-1808-II-MB
•Easily Programmed Six-Digit User Code
•Simple 9-Volt Battery Replacement
•Fast One-Second Fingerprint Access, Sensor Quickly Reads Fingerprint in Any Position
and Automatically Unlocks
•Program up to Three User Codes and Five Associated Fingerprints per User Code, Total
of Fifteen Fingerprints
•User Code and Fingerprints Stored in Memory Within Safe Door Shielded, Along with
Internal Lock, From Drill Attacks by Ball Bearing Drill Protection Plate
•User Code Remains in Memory for Years Even if Battery or Keypad Destroyed or
Removed
•Lock’s Memory Protected Inside the Safe and Cannot be Hotwired
•After Several Incorrect User Code/Fingerprint Attempts Lock Begins Lockout Delay
Period Disabling All Inputs to Keypad Delaying Further Tampering
OPERATING INSTRUCTIONS
Opening Safe for the First Time
SecuRam® ScanLogic™ Biometric Electronic Lock is shipped unlocked. Open the door by
rotating the hub on the front of the safe clockwise and pulling the safe door open. If the
hub seems stiff, insert a solid round wooden stick into one of the handle holes and turn
the hub clockwise to open. Then install the handles, if applicable.
Installing the Battery
Rhino Metals highly recommends using a 9-volt Duracell®or Energizer®alkaline
battery with a “Use Date” of at least four years in the future.
1. Unlock and pull the safe door open.
2. To remove the keypad, push straight up from the bottom of the keypad until it
releases.
3. Carefully pull the keypad away from the safe to prevent
damage to the wiring harness, revealing the battery
cavity.
4. With the battery cavity accessible, install a new 9-volt
battery into the terminals and tuck the battery and wiring
harness back into the battery cavity.
5. Slide the keypad back down onto the shoulder screws. Be
careful not to pinch the wiring harness on the screws.
6. With the door open, test the operation of the lock several
times before closing and locking the safe.

Operating the Electronic Lock
1. To unlock the safe, enter the existing six-digit user code (or fingerprint). Each
key press is confirmed with an audio and visual (LED flash) signal.
2. The lock will indicate a valid user code entry with a double signal. Within four
seconds, turn the handle or hand wheel clockwise to retract the locking bolts.
3. To lock the safe, turn the handle counter-clockwise until it stops to allow the
locking bolts to extend. Always test to see if the lock has re-engaged by turning
the handle clockwise.
Wrong Try Penalty
Every invalid user code entry is indicated by a triple signal. Entering five consecutive
invalid user codes will result in a five-minute delay period. The keypad will beep
every five seconds and the buttons on the keypad are not operable. Two beeps
indicate penalty time has expired and the beeping will stop, enter valid user code to
open the safe lock. At the end of the delay period, two incorrect user codes will
restart an additional five-minute delay period.
Changing User Code and Fingerprint
SecuRam® Electronic Lock user codes are set at the factory as 1-2-3-4-5-6 and
preset fingerprint. For security purposes, immediately change the user code to a
unique user code. The six-digit user code can be changed at any time. When
creating a new user code, avoid using personal data such as birth dates, street
numbers or phone numbers to keep valuables as secure as possible. Choose a
personal six-digit user code that can easily be remembered.
User Code
1. Press “0” six times.
2. Enter existing six-digit user code, one beep.
3. Enter NEW six-digit user code, one beep.
4. Repeat NEW six-digit user code, two beeps.
5. Enter NEW six-digit user code once more to unlock the lock.
6. Test the lock several times with the NEW user code before closing and
locking the safe.
Fingerprint
1. Hold “+”, one beep.
2. Place fingerprint four times, one beep each.
3. Two beeps confirm fingerprint addition.
4. Test the lock several times with the NEW fingerprint before closing and
locking the safe.
Always have the safe door open and locking bolts extended whenever
changing the user code or fingerprint.
During the delay period, pressing any key or removing the battery will extend the
delay period for up to five minutes.

If a mistake is made, wait 30 seconds and then repeat above steps.
LOW BATTERY IS THE MOST COMMON CAUSE OF ELECTRONIC LOCK ISSUES.
Repeated beeping during opening or any other unfamiliar occurrences
indicates that the battery is low and needs to be replaced immediately.
Lost User Code for Electronic Locks
Most safes with electronic locks have their override user code on file at Rhino Metals.
The override user codes are tracked by model and serial number. If user code is lost, a
$25.00 research fee will be assessed for restoring the user code. The request requires
completing and providing proper documentation of ownership of the safe.
Rhino Metals cannot guarantee that Rhino Metals can recover a user code or
responsibility for keeping the information. Please keep user code in a secure place
outside the safe.
IMPORTANT FOR ELECTRONIC LOCKS
♦
DO NOT CLOSE THE SAFE DOOR IF THE USER CODE OR FINGERPRINT DOES NOT
WORK. Refer to the Troubleshooting Guide or call Rhino Metals Tech Support for
further assistance. Do not wait until the safe is locked out.
♦ Store the safe’s model, serial number, Owner’s Manual, and user code in a
secure location outside the safe.
♦ When a user code is changed, always check to make sure the previous user
code will no longer open the lock.
♦ Replace the battery annually to ensure reliable access into the safe.
♦ Always center the handle or hand wheel with the safe door to ensure that there is
no pressure on the lock as it could cause a lockout.
♦ Consider purchasing an Extended Lock Warranty for extended services.
CARE AND MAINTENANCE
Cleaning the Safe Body
Use a clean and soft cloth (such as a microfiber cleaning cloth) that is slightly
damp with water to clean the exterior of the safe. Take care around the edges
of any logos or pin striping as any pressure could cause damage to them.
Cleaning Safe Locks and Handles
Locks and handles are coated to protect from rust or tarnish. Do not use any
kind of metal polish or harsh cleaning products. Simply wipe off with a soft,
damp cloth. Minor scratches may be touched up with a paint touch up kit
available from Rhino Metals.
Electronic Lock Maintenance
While electronic locks do not need annual maintenance, changing out the
battery once a year is highly recommended to ensure reliable access into the
safe. Rhino Metals recommends using a 9-volt Duracell® or Energizer® alkaline
battery with a “Use Date” of at least four years in the future.

TROUBLESHOOTING
Common Issues Possible Solutions
Electronic Lock Not
Working Properly
Replace the battery with a new 9-volt Duracell® or Energizer®
alkaline battery with a “Use Date” of at least four years in the
future.
Any pressure on the side of the lock tang might prevent the lock
from operating properly. If attempting to unlock the safe, rotate
the handle counter-clockwise and keep a slight pressure
on the
handle while entering the user code or fingerprint. Once two
beeps are heard, wait for two seconds, and then rotate hub or
hand wheel clockwise to open. If attempting to lock the safe, turn
the handle counter-
clockwise until it stops, then press and hold
the handle counter-clockwise for seven seconds before checking if
it is locked.
Make sure the wiring harness is properly and tightly connected to
the keypad with no pinched wires or bent connectors.
If the light on lock is randomly flashing, lock may be in a delay
period. Do not attempt to enter any user code or fingerprint for
a period of fifteen minutes. If attempting to enter a user code or
fingerprint while in a delay period, the delay will be extended.
Changing or removing the battery on the keypad while in a delay
period will also extend the delay. After waiting for the duration
of the delay period and the light stops flashing, then enter the
user code. If it is still flashing randomly, wait up to two hours
before trying again.
Lock Beeps Ten
Times After User
Code or
Fingerprint Entry
Replace the battery with a new 9-volt Duracell® or Energizer®
alkaline battery.
Green Lights After
Input of User Code
or Fingerprint
This is an indication of a valid user code or fingerprint.
Red Lights After
Input of User Code
or Fingerprint
This is an indication of an invalid user code or fingerprint.
Lost Combination
See Lost Combination instructions, depending on lock type. Rhino
Metals cannot give combinations over the phone as there is no
method to verify ownership of the safe.

WARRANTY CLAIMS AND REPAIRS
Please carefully read the Limited Lifetime Warranty. It details the length of
coverage and limitations for services and repairs. All Warranty services must be
pre-authorized by Rhino Metals and require completing and providing proper
documentation of ownership of the safe. If any Warranty questions, contact a local
authorized dealer or Rhino Metals Tech Support. It is the sole responsibility of the
safe owner for payment of any services or repairs done without pre-authorization
from Rhino Metals.
INSURANCE COVERAGE
Rhino Metals highly recommends purchasing additional insurance coverage to the
total value of the contents in the safe. The Limited Lifetime Warranty does not
insure any of the contents inside the safe. Most homeowner insurers require
purchasing endorsements or riders for valuables exceeding the standard coverage
policy for personal items. Be sure to check with the residential insurance provider for
more details.

LIMITED LIFETIME WARRANTY
Rhino Metals offers to the original Purchaser, a Limited Lifetime Warranty, covering
defects in workmanship, material, damage by unlawful attempted or actual break-in, and
fire. Warranty applies only to safes located in the United States and Canada, purchased
at an authorized Rhino Metals safe dealer, and that have been used solely in residential
applications. Commercial or industrial use applications carry a one-year Warranty against
defects in workmanship and materials.
To receive Warranty support, Purchaser must provide Rhino Metals with (1) proof of
purchase, (2) serial number on safe; (3) a written statement, (4) photographs of the
damaged safe, and (5) a police or fire department report. Rhino Metals will make the
decision to repair the safe in-home, at the factory, or replace the safe altogether. If
possible, the safe will be repaired locally. If the safe is to be repaired at the factory or
replaced, Rhino Metals will, at its expense, have the safe opened, if required, and will
pay for the freight back to the factory. Purchaser must package and palletize the safe
and make the safe available for a curbside pickup at Purchase expense. The Warranty
does not cover any costs for removal or installation of the safe or its contents. Personal
property in the safe is not covered by the Warranty.
The obligation of Rhino Metals under Warranty is contingent upon proper use,
installation, and maintenance of the safe and shall not apply to safes or safe parts which
have been neglected, misused, or exposed to extreme or unusual environments.
Failure to anchor the safe using factory pre-drilled holes voids Warranty. Any modifying
or tampering with the safe which alters or affects the safe’s use or operation will void
the Warranty.
Without limit, the Warranty specifically excludes any liability for defects or damage
caused or increased use of unauthorized parts. Upon purchase, the Purchaser must
promptly notify Rhino Metals of any defects. The Purchaser’s remedies are solely limited
to replacing parts or repair and are at the discretion of Rhino Metals. Warranty gives
Purchaser specific legal rights, and may also have other rights which vary from state to
state.
Locks and electronic keypads carry a five-year Warranty for labor and parts. The
Warranty does not cover forgotten or lost user codes, lost keys, dead or weak batteries,
or improper opening procedures. Lights and electrical components carry a one-year
Warranty. Paint or powder coat finish and interior are under Warranty for one year
based on proper care and environment.
The Warranty is given in place of all other Warranties and assurances, whether
expressed or implied, including but not limited to matters of merchantability, quality, or
fitness for purpose. Rhino Metals accepts no liability under any circumstances
whatsoever for any incidental or consequential damage or loss suffered by anyone as a
result of using or being unable to use the safe.

EXTENDED LOCK WARRANTY (SOLD SEPARATELY)
Rhino Metals offers to the original Purchaser, an Extended Lock Warranty, covering
defects in workmanship and material on either electric or manual locks. Locks and
electronic keypads carry a five-year Warranty for labor and parts. The Warranty does
not cover forgotten or lost user codes, dead or weak batteries, or improper opening
procedures. The Warranty applies only to safes located in the United States and
Canada, purchased at an authorized Rhino Metals safe dealer, and that have been
used solely in residential applications. Commercial or industrial use applications carry
a one-year Warranty against defects in workmanship and materials.
Extended Lock Warranty coverage extends the existing Lock Warranty for an
additional two-years at $30.00 or four years at $60.00. To receive Warranty support,
Purchaser must provide Rhino Metals with (1) proof of purchase, (2) serial number on
safe, and (3) payment. For payment, Rhino Metals accepts Visa, Discover,
Mastercard, Amex and money orders made payable to Rhino Metals.
Rhino Metals will make the decision to repair the lock in-home, at the factory, or
replace the lock altogether. If possible, the lock will be repaired locally. If the lock is
to be repaired at the factory or replaced, Rhino Metals will, at its expense, have the
safe opened, if required, and will pay for the freight back to the factory. The
Purchaser must package the safe and make the safe available for a curbside pickup
at their expense. The Warranty does not cover any costs for removal or installation
of the safe, lock or its contents. Personal property in the safe is not covered by the
Warranty.
The obligation of Rhino Metals under Warranty is contingent upon proper use,
installation, and maintenance of the lock. Warranty shall not apply to locks which
have been neglected, misused, or exposed to extreme or unusual environments. Any
modifying or tampering with the lock which alters or affects the lock’s use or
operation will void the Warranty.
Without limit, the Warranty specifically excludes any liability for defects or damage
caused or increased use of unauthorized parts. Upon purchase, the Purchaser must
promptly notify Rhino Metals of any defects. The Purchaser’s remedies are solely
limited to replacing parts or repair and are at the discretion of Rhino Metals. The
Warranty gives specific legal rights and has other rights which vary from state to
state.
Warranty is given in place of all other Warranties and assurances, whether
expressed or implied, including but not limited to matters of merchantability, quality,
or fitness for purpose. Rhino Metals accepts no liability under any circumstances
whatsoever for any incidental or consequential damage or loss suffered by anyone
because of using or being unable to use the lock.
To purchase the Extended Lock Warranty, go to www.rhinosafe.com (or complete
and return the purchase form located below) within 30 days to Rhino Metals.
Warranty must be purchased within 30 days of safe purchase to become valid.