Securam ScanLogic Optical Installation manual

Programming
ScanLogic Basic
A. Open lock
1) Enter default Manager code 123456
B. Change Code
1) Enter 000000
2) Enter existing code, 1 beep
3) Enter new 6 digit code, 1 beep
4) Repeat new 6 digit code, 2 beeps
*Manager code of 123456 must be changed before
any other Users can be added
**Reset Code must be changed from default
***1 long beep means code is not allowed
C. Add Manager fingerprint(s)
1) Open with Manager code/fingerprint
2) Hold “+,” and hold until 1 beep
3) Place fingerprint 4X, 1 beep each
4) 2 beeps confirms fingerprint addition
*Manager can add up to 5 fingerprints
D. Add User1 Code
1) Open with Manager code/fingerprint
2) Hold “1,” 1 beep
3) Enter new 6 digit code, 1 beep
4) Repeat new 6 digit code, 2 beeps
E. Add User2 Code
1) Open with User1 code/fingerprint
2) Hold “1,” 1 beep
3) Enter new 6 digit code, 1 beep
4) Repeat new 6 digit code, 2 beeps
F. Add fingerprints
5) Open with own code/fingerprint
6) Hold “+,” 1 beep
7) Place fingerprint 4X, 1 beep each
8) 2 beeps confirms fingerprint addition
*User1 and User2 can add up to 5 fingerprints
G. Delete own fingerprints (All)
1) Open with your own code/fingerprint
2) Hold “-”, 2 beeps
*All of your fingerprints have been deleted
H. Delete User2 (Code & fingerprints)
1) Open with User1 code/fingerprint
2) Hold “3”, 2 beeps
*User2 code and fingerprints are deleted
I. Delete All (Codes/fingerprints)
1) Open with manager code/fingerprint
2) Hold “3”, 2 beeps
*Manager code remains unchanged, User1 and
User2 are deleted
J. Reset (resets codes to factory default)
1) Input reset code, default is 999999
2) Hold “6”, 2 beeps
*Lock is in default mode, Manager code reverts to
123456, Reset code remains unchanged
K. Turn beeper off
1) Open with Manager or User1
code/fingerprint
2) Hold “4,” 1 beep
L. Turn beeper on
1) Open with Manager or User1
code/fingerprint
2) Hold “4,” 2 beeps
Security Levels:
Security Level 1 = Fingerprint or code
Security Level 2 = Fingerprint and code
M. Change to Security Level 2 (fingerprint and
code)
1) Open with Manager or User1
code/fingerprint
2) Hold “5,” 1 beep, then 2 beeps
N. Change to Security Level 1 (fingerprint or
code)
1) Open with Manager or User1 code and
fingerprint
2) Hold “5,” 1 beep, then 1 beep
**The Reset Code must be changed from default 999999 to a unique
number. Follow the Change Code process detailed in Item “B.”below.

Penalty Time
1) The entry of 5 incorrect codes will cause
the lock to enter Penalty Time where the
lock is lock down for a period of 5 minutes.
You cannot open the lock during the
penalty time period.
2) During the Penalty Time, the keypad will
beep every 5 seconds and the buttons on
the keypad are not operable. Entering
additional codes during penalty time does
not extend penalty time.
3) Two beeps indicates penalty time has
expired and the beeping will stop, enter a
valid code to open the safe lock.
4) Note: If after penalty expires you enter an
invalid code two more times, the lock will
go back into penalty time.
Troubleshooting
1) Lock beeps 10 times after
fingerprint/code entry: This is the low
battery indicator. Replace the battery
with a new Duracell or Energizer battery.
2) Green lights after input of fingerprint or
code –this is an indication of a valid
fingerprint or code entry
3) Red lights after input of fingerprint or
code –this is an indication of an invalid
fingerprint or code entry