Sena FreeWire SP29 User manual

FreeWire
Bluetooth CB and Audio Adapter
SENA www.sena.com User’s Guide

CONTENTS
1. INTRODUCTION
2. PACKAGE CONTENTS
3. INSTALLING THE FREEWIRE
3.1 Installing on the Handle Bar
3.2 Placing on the Mounting Cradle
4. POWERING ON/OFF AND CHARGING
4.1 Powering On
4.2 Battery Check
4.3 Charging
5. PAIRING THE FREEWIRE WITH BLUETOOTH DEVICES
6. USING THE FREEWIRE
6.1 Connections
6.2 Using with a headset
6.4 Reset to Factory Default Settings
6.5 Fault Reset
7. QUICK REFERENCE
BATTERY INFORMATION
MAINTENANCE AND CARE
DISPOSAL
CERTIFICATION AND SAFETY APPROVALS
FCC Compliance Statement
FCC RF Exposure Statement
FCC Caution
Bluetooth License
WAIVER AND GENERAL RELEASE
Limitation of Liability
Return for Full Refund
WARNING

© 1998-2016 Sena Technologies, Inc. All rights reserved.
Sena Technologies, Inc reserves the right to make any changes and improvements to its product without providing prior
notice.
Sena™ is a trademark of Sena Technologies, Inc. or its subsidiaries in the USA and other countries. FreeWire™, Prism™, Bluetooth
Audio Pack for GoPro®, Tufftalk™, 20S™, 10S™, 10C™, 10U™, 10R™, 3S™, SMH10™, SMH10R™, SMH5™, SMH5-FM™,
SMH3™, SPH10™, SPH10H™, SPH10H-FM™, SPH10S™, Expand™, Bluetooth Mic&Intercom™, Handlebar Remote™, Wristband
Remote™, SM10™, SR10™, SR10i™ are trademarks of Sena Technologies, Inc. or its subsidiaries. These trademarks may not be
used without the express permission of Sena.
GoPro®is a registered trademark of Woodman Labs of San Mateo, California. Sena Technologies, Inc. (“Sena”) is not affiliated with
Woodman Labs. The Sena Bluetooth Pack for GoPro® is an after-market accessory specially designed and manufactured by Sena
Technologies, Inc. for the GoPro® Hero3 and Hero4 allowing for Bluetooth capabilities. Harley-Davidson®is a registered trademarks of
H-D Michigan, Inc. and Harley-Davidson, Inc. Honda® and Gold Wing® are trademarks of Honda Motor Co., Ltd. Sena is not affiliated
with Harley-Davidson, H-D Michigan, Inc. or Honda Motor Co., Ltd. Other trademarks and tradenames are those of their respective
owners.
The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Sena is under license.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received. Including interference that may cause undesired operation
Note : This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15
of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated
in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
ÿLe present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisee aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d'en
compromettre le fonctionnement. ÿ
Caution: Any changes or modifications in construction of this device which are not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
Hereby, SENA TECHNOLOGIES.Inc Declares that this Freewire is in compliance with the essential requirements and
other relevant provisions of directive 1999/5/EC.

1. INTRODUCTION
Thank you for choosing the Sena FreeWire. The FreeWire is a Bluetooth CB radio and audio adaptor. You can connect
the FreeWire to the motorcycle onboard audio system and make the audio system transfer stereo audio (music, FM radio,
navigation etc.) to a Sena Bluetooth headset.
You can communicate through the built-in CB radio in the onboard audio system using the FreeWire. Also, if you have a
mobile phone connected to the motorcycle onboard audio system by a cable, you can have mobile phone calls using your
headset.
When a rider and a passenger connect the FreeWires to each port and pair a Sena headset to each FreeWire, they can
communicate with each other using the bike’s internal communication network.
Please read this User’s Guide carefully before using the FreeWire. Also refer to www.sena.com for the latest version of
the User’s Guide and additional information related to Sena Blueooth products.
The FreeWire Features:
●Support for onboard built-in CB radio communication
●Wirelessly stream stereo audio to Sena Bluetooth headset
●Support for internal communication between a rider and a passenger each using a FreeWire
●AUX input for GPS, radar detector or laser detector
●Mix the audio sources from the AUX input and the onboard audio system
●12V bike-powered kit with On/Off controlled by the ignition switch
●Firmware upgradeable
Technical Specifications:
●Bluetooth 4.1
●Advanced Audio Distribution Profile (A2DP)
●Operating time: 7 hours
●Battery charging time: 2.5 hours
●Lithium polymer battery

●Dimensions: 83 mm X 45 mm X 25 mm (3.3 in X 1.8 in X 1.0 in)
●Weight: 50 g (1.76 oz)
●CE, FCC, IC

2. PACKAGE CONTENTS
2.1 FreeWire for Harley-Davidson Package
• Main Unit
• Handlebar Mounting Kit
• Mounting Cradle
• USB Power & Data Cable (Micro USB type)
• Micro USB to 7 Pin DIN Cable for Harley-Davidson
• 3.5 mm Stereo Audio Cable - Straight
• Cigarette Charger (Jack Type)
2.2 FreeWire for Honda Goldwing Package
• Main Unit

• Handlebar Mounting Kit
• Mounting Cradle
• USB Power & Data Cable (Micro USB type)
• Micro USB to 5 Pin DIN Cable for Honda Goldwing
• 3.5 mm Stereo Audio Cable - Straight
• Cigarette Charger (Jack Type)

3. INSTALLING THE FREEWIRE
3.1 Installing on the Handlebar
1. Attach the mounting kit on the back of the FreeWire along the guide rail.
2. Place the main unit on the handlebar, wind the rubber band around the handlebar, and hang it on the hook.
3.2 Placing on the Mounting Cradle
1. Locate a proper surface on your motorcycle body, clean the body surface location with a moistened towel, and
allow to dry thoroughly.
2. Peel off the cover of the adhesive tape of the mounting cradle and attach the unit on the proper surface of your
motorcycle.

4. POWERING ON/OFF AND CHARGING
4.1 Powering On/Off
To power on the FreeWire, slide the Power Switch to on. The Blue and Red LEDs will turn on. To power off, slide the
Power Switch to off.
4.2 Battery Check
When the FreeWire is powering on, the Red LED flashes rapidly indicating the battery level.
4 flashes = High, 70~100%
3 flashes = Medium, 30~70%
2 flashes = Low, 0~30%
4.3 Charging
It takes about 2.5 hours to be completely charged. The Charging LED becomes solid blue from solid red when it is
completely charged.
Note:
The FreeWire is automatically powered on and off by using the cigarette charger within the 12V bike-powered kit.

5. PAIRING THE FREEWIRE WITH BLUETOOTH DEVICES
The FreeWire must be paired with a Bluetooth headset to connect with the onboard audio system. Please take the
following steps to pair with your Bluetooth headsets.
1. Turn on your Bluetooth headset and enter pairing mode, following the Bluetooth headset manual.
2. Turn on the FreeWire and press and hold the Center Button for 5 seconds until the LED flashes red and blue
alternatively.
3. When the pairing is successful, the blue LED flashes slowly.

6. USING THE FREEWIRE
6.1 Connections
The FreeWire has one Onboard Audio In Port for wired connection with the onboard audio system and one AUX Port for
wired connection with other devices.
●Onboard Audio In: Onboard audio system input
To connect the Harley-Davidson Ultra Classic Audio System with the FreeWire, use the included Micro USB to 7 Pin DIN
cable.
To connect the Honda Goldwing Audio System with the FreeWire, use the included Micro USB to 5 Pin DIN cable.
AUX: Auxiliary audio input
To connect extra devices such as navigation, radar detector, or laser detector with the FreeWire, use the included 3.5mm
Stereo Audio Cable. The AUX signal mixes with the motorcycle onboard audio system.
Note:
Whenever there is an incoming AUX signal, the volume of Onboard Audio In is down to a certain level.
6.2 Using with a headset
1. Turn on Bluetooth headsets that are already paired with the FreeWire.
2. Turn on audio devices connected with the FreeWire.
3. Turn on the FreeWire.
4. The Freewire automatically connects to the paired Bluetooth headsets. You will be able to hear audio sounds.
5. If you can’t hear any sound, press the Center Button of the FreeWire. The FreeWire tries to connect the paired
Bluetooth headset again.
Note:
If there is a GPS system connected to the FreeWire, the turn-by-turn navigation audio will not be heard if you have a
conversation on your phone or intercom. This is due to the set priority within the FreeWire.
6.4 Reset to Factory Default Settings
1. Power on the FreeWire and press the Center Button on the FreeWire for 14 seconds until the Blue and Red LED
is rapidly flashing.
2. Within 10 seconds, press the Center Button to confirm reset. The FreeWire will be restored to factory settings and
returns to stand-by mode.
6.5 Fault Reset
If the FreeWire is not working properly or is in a faulty status for any reason, you may reset by pushing the small reset
button at the back of the FreeWire Unit. By using a paperclip or a pencil tip, lightly press and hold the reset button for 1
second. The FreeWire will be switched off and automatically switched on again. Turn the FreeWire back on to use it.

However, this will not restore the FreeWire to factory default settings.
7. QUICK REFERENCE
●Buttons
Button
Description
Duration
LED
Power Switch ON
Power on
-
Solid blue and solid red
Power Switch OFF
Power off
-
LEDs off
Center Button
Headset Pairing
5 secs
Blue and Red LEDs rapidly flashing
Factory Reset
14 secs
Red LED rapidly flashing
Factory Reset Confirm
Tapping
LEDs off
Fault Reset Button
Fault Reset
Pressing
●LED Indicators
LED
LED Status
Description
Blue LED
Solid
Headset idle
Slow Flashing
Headset connected / Audio
streaming
Double Flashing
AUX muted
●Charging LED Status
LED
Description
Solid Red
Charging
Solid Blue
Fully charged

CERTIFICATION AND SAFETY APPROVALS
FCC Compliance Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the
FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to try
to correct the interference by one or more of the following measures:
●Reorient or relocate the receiving antennae
●Increase the separation between the equipment and the receiver
●Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
●Consult the dealer or an experienced radio/TV technician for help.
FCC RF Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must
follow the specific operating instructions for satisfying RF exposure compliance. The antenna used for this transmitter
must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter
product procedures.
FCC Caution
Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void
user’s authority to operate the equipment.
CE Declaration of Conformity
This product is CE marked according to the provisions of the R&TTE Directive (99/5/EC). Hereby, Sena declares that this
product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. For further
information, please consult www.sena.com.Please note that this product uses radio frequency bands not harmonized
within EU. Within the EU this product is intended to be used in Austria, Belgium, Denmark, Finland, France, Germany,
Greece, Ireland, Italy, Luxembourg, The Netherlands, Portugal, Spain, Sweden, United Kingdom and within EFTA in
Iceland, Norway and Switzerland.

Industry Canada Statement
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two
conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
Bluetooth License
The Bluetooth®word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Sena is under
license. Other trademarks and trade names are those of their respective owners.
The product is compliant with and adopts the Bluetooth®Specification 3.0 and has successfully passed all interoperability
tests that are specified in the Bluetooth® specification. However, interoperability between the device and other
Bluetooth®-enabled products is not guaranteed.
WEEE (Waste Electrical and Electronic Equipment)
The crossed-out wheel bin symbol on the product, literature, or packaging reminds you that all electrical and electronic
products, batteries, and accumulators must be taken to separate collection at the end of their working life. This
requirement applies to the European Union and other locations where separate collection systems are available. To
prevent possible harm to the environment or human health from uncontrolled waste disposal, please do not dispose of
these products as unsorted municipal waste, but hand it in at an official collection point for recycling.
SAFETY INFORMATION
Please ensure that the product is properly used by observing the warnings and cautions below to prevent any risk and/or
damage to property.
Product Storage and Management
●Keep the product free of dust. It may damage mechanical and electronic parts of the product.
●Do not store the product in high temperatures as this may reduce the lifespan of electronic devices, damage the
battery, and/or melt plastic parts of the product.
●Do not store the product in cold temperatures. Abrupt changes in temperatures may cause condensation and
damage electronic circuits.
●Do not clean the product with cleaning solvents, toxic chemicals, or strong detergents as this may damage the
product.
●Do not paint the product. Paint may obstruct moving parts or interfere with the normal operation of the product.
●Do not drop or otherwise shock the product. It may damage the product or its internal electronic circuits.
●Do not disassemble, repair or modify the product as this may damage the product and invalidate the product
warranty.
●Do not store the product in humid environments, especially for long time storage.

Product Use
●Do not cause impact to the product or touch it with sharp tools as this may damage the product.
●Do not use the product in high-temperatures or apply heat to the product as this may cause damage, explosion, or
fire.
●Keep product away from pets or small children. It may damage the product.
●In any place where wireless communication is prohibited, such as hospitals or airplanes, turn off the power and
refrain from using the product. In a place where wireless communication is prohibited, electromagnetic waves may
cause hazards or accidents.
●Do not use the product near hazardous explosives. When it is near any explosion hazards, turn off the power and
heed any regulations, instructions, and signs in the area.
●When using the product, be certain to conform to laws regarding the use of communications devices while riding.
●Do not put the product where it may hamper the rider's vision or manipulate it while riding. This may cause traffic
accidents.
●If the product is damaged, stop using it immediately. It may cause damage, explosion, or fire.
Battery
This product has an irreplaceable rechargeable battery inside. Therefore, when using the product, make sure to adhere to
the following:
●Never separate the battery from the product as this may damage the product.
●The battery performance may be reduced over time with usage.
●In recharging the battery, make sure to use an approved charger provided by the manufacturer. Use of a non-
approved charger may cause fire, explosion, leakage, and other hazards may also reduce the life time or
performance of the battery.
●Any 3rd party USB charger can be used with Sena products if the charger is approved by either the FCC, CE, IC or
other locally approved agencies that Sena accepts.
●Do not use cigarette chargers other than the included cigarette charger to charge the headset.
●Store the battery at temperatures of 15°C~25°C (59°F~77°F). Higher or lower temperatures may reduce the
capacity and life of the battery, or may cause temporary non-operation. Do not use the product in sub-zero
temperature, because it may cause serious reduction of the battery performance.
●If you apply heat to the battery or throw it into fire, it may explode.
●Do not use the product with a damaged battery. It may explode and/or cause accidents.
●Never use a damaged charger. It may explode and/or cause accidents.
●Battery life may vary depending on conditions, environmental factors, functions of the product in use, and devices
used with it.
MAINTENANCE AND CARE
The FreeWire should be treated with care and the following suggestions will help you protect your warranty coverage.
1. Do not use or store the device in dusty, dirty areas. Its moving parts and electronic components can be damaged.

2. Do not store the device in hot areas. High temperatures can shorten the life of electronic devices, damage
batteries, and wrap or melt certain plastics.
3. Do not store the device in cold areas. When the device returns to its normal temperature, moisture can form
inside the device and damage electronic circuit boards.
4. Do not attempt to open the FreeWire.
5. Do not drop or knock the device. Rough handling can break internal circuit boards and fine mechanics.
6. Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the device.
7. Do not paint the device. Paint can clog the moving parts and prevent proper operation.
PRODUCT WARRANTY AND DISCLAIMER
Limited Warranty
Limited Warranty
Sena Technologies, Inc. (“Sena”) guarantees the product quality based on the technical specification stated in the product
manual, and data regarding product warranty. Here, product warranty extends to the product only. Sena will not be liable
for any loss, damage of human life, or loss of property which may result from using the product beyond defective parts or
flaws that occur due to problems in manufacture.
Warranty Period
Sena guarantees free-of-charge replacements of defective parts of the product or flaws that may have occurred due to
problems in manufacture for a period of 2 years from the date of initial purchase.
Termination
Quality warranty of the product becomes effective on the date of initial purchase. In addition, the quality warranty of the
product expires when the warranty period expires. However, in the following cases, the warranty will be terminated
prematurely.
●In the event the product has been sold or transferred to a third party.
●In the event the manufacturer's name, serial number, product label, or other markings have been modified or
removed.
●In the event any unauthorized person has tried to disassemble, repair, or modify the product.
Notice and Waiver
By buying and using this product, you relinquish considerable legal rights including any claim for compensation for
damages. Therefore, be certain to read and understand the following terms and conditions before using the product. Use
of this product will constitute consent to this agreement, and forfeiture of rights to all claims. If you do not consent to all the
terms and conditions of this agreement, return the product for a refund. (Refer to the section "Return for Full Refund".)
1. You agree that you, your descendants, legal proxies, successors, or transferees will not raise permanent volitional
request for any suit, claim, implementation, redemption or similar action from Sena with regard to any occasion such
as difficulty, pain, suffering, inconvenience, loss, injury, or death which may occur to you or a third party during the
use of this product.
2. You must completely understand and accept all risks (including those occurring due to any careless behavior of

yours or others) which may occur during the use of this product.
3. You are responsible for ensuring that your medical condition permits usage of the product and that you are in
sufficient physical condition for using any device which can be used with it. In addition, you must ensure that the
product does not limit your abilities and that you are able to use it safely.
4. You must be an adult who can take responsibilities for using the product.
5. You must read and understand the following warnings and alerts:
●Sena; together with employees, managers, partners, subsidiaries, representatives, agents, supporting firms and
suppliers, sole sellers of Sena (collectively referred to as "the company") recommend that, before using the
product and similar devices of any brands including its derivative models, you collect any relevant information in
advance and be entirely prepared in terms of weather, traffic situation, and road conditions.
●When you use the product while you operating any vehicle or equipment such as motorcycles, scooters, mopeds,
ATVs, or quad-bikes (hereinafter called as "transportation means"), you must take complete caution regardless of
the location of such operation.
●Use of the product on the road may cause such risks as fracture, serious disability, or death.
●Risk factors, which may occur when you use the product, may be due to errors of the manufacturer, its agents, or
third parties which are involved in the manufacturing.
●Risk factors, which may occur when you use the product, may be unforeseeable. Therefore, you must take full
responsibility for any damage or loss caused by all risk factors which may occur when using the product.
●When you use the product, use good judgment; never use it under the influence of alcohol.
6. You must read and completely understand all terms and conditions of legal rights and warnings that are involved in
using the product. In addition, usage of the product constitutes acceptance of all terms and conditions regarding
waiver of rights.
Warranty Exclusions
Reasons for Limited Liabilities
If you do not return the product after purchasing it, you relinquish all rights to liabilities, loss, claims, and claims for
reimbursement of expenses (including attorney's fees). Therefore, Sena will not be liable for physical injury, death, or any
loss or damage of transportation means, possessions, or assets which belong to you or third parties that may have
occurred while you use the product. Further, Sena will not be liable for any substantial damage not related to the condition,
environment, or malfunction of the product. All risks related with the operation of the product depend entirely on the user
regardless of its use by the initial purchaser of a third party.
Use of this product may violate local or national laws. In addition, be aware once again that correct and safe use of the
product is entirely your responsibility.
Limitation of Liability
TO THE FULL EXTENT ALLOWED BY LAW, SENA EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY,
WHETHER BASED IN CONTRACT OR TORT (INCLUDING NEGLIGENCE), FOR INCIDENTAL, CONSEQUENTIAL,
INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE OR PROFITS, LOSS OF
BUSINESS, LOSS OF INFORMATION OR DATA, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN
CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE, OR
INTERRUPTION OF ITS PRODUCTS, EVEN IF SENA OR ITS AUTHORIZED RESELLER HAS BEEN ADVISED OF

THE POSSIBILITY OF SUCH DAMAGES, AND LIMITS ITS LIABILITY TO REPAIR, REPLACEMENT, OR REFUND OF
THE PURCHASE PRICE PAID, AT SENA’S OPTION. THIS DISCLAIMER OF LIABILITY FOR DAMAGES WILL NOT BE
AFFECTED IF ANY REMEDY PROVIDED HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE. IN ANY CASE, THE
TOTAL COMPENSATION LIABILITIES OF SENA OR ITS SALES AGENTS SHALL NOT EXCEED THE PRICE PAID
FOR THE PRODUCT BY THE PURCHASER.
Liabilities Disclaimer
In addition to damages which may occur due to the use of the product, Sena will not be liable for damages of the product
which occur due to the following events.
In the event the product is misused or used for purposes other than its intended purposes.
In the event the product is damaged because the user does not follow the content of the product manual.
In the event the product is damaged because it has been left unattended or has undergone any other accident.
In the event the product is damaged because the user has used any parts or software which are not provided by the
manufacturer.
In the event the product is damaged because the user has disassembled, repaired, or modified it in such way as is not
explained in the product manual.
In the event the product is damaged by a third party.
In the event the product is damaged due to Acts of God (including fire, flood, earthquake, storm, hurricane or other natural
disaster).
In the event the surface of the product is damaged by use.
Warranty Service
To obtain product warranty service, send the defective product, at your expense, to the manufacturer or the seller along
with proof of purchase (a receipt that shows the purchase date, a product registration certificate of the Website, and other
relevant information). Take necessary measures to protect the product. In order to get a refund or replacement, you must
include the whole package as it was purchased.
Free-of-charge Service
Sena will provide free-of-charge repair or replacement service for the product when product defects occur within the
scope of the product warranty during the warranty period.
Return for Full Refund
Should you not agree to the terms and conditions explained above, you may return the product for a full refund. To get a
refund, within 14 days from the purchase date you must return the product to the seller in such a condition as it was
purchased.
Unless you return the product within 14 days from the purchase date, you will have read and agreed to all the terms and
conditions explained above, and Sena will not be liable for any claim for damages related with the product.

CERTIFICATION ET HOMOLOGATION EN TERMES DE SÉ CURITÉ
Déclaration de conformité FCC
Cet appareil est en conformité avec la partie 15 de la réglementation FCC. L'exploitation est autorisée aux deux
conditions suivantes :
(1) Cet appareil ne doit pas créer d’interférences préjudiciables et
(2) Cet appareil doit accepter toutes les interférences reçues, y compris celles qui pourraient entraver son bon
fonctionnement.
Ce matériel a été testé et déclaré en conformité avec les limites d'un appareil numérique de Classe B, suivant la partie 15
de la réglementation FCC. Ces limites sont destinées à assurer une protection raisonnable contre les interférences
préjudiciables dans un environnement résidentiel. Ce matériel génère, utilise et peut dégager de l’énergie en radio
fréquence et, s’il n’est pas installé et utilisé en conformité avec les instructions, peut provoquer des interférences
préjudiciables avec les communications radio. Cependant, il n’y a aucune garantie que des interférences ne se produiront
pas dans des installations particulières. Si ce matériel provoque des interférences préjudiciables à une réception radio ou
TV, ce qui peut être déterminé en allumant puis en éteignant l'appareil, il est vivement recommandé à l'utilisateur
d'essayer de mettre un terme à ces interférences en prenant l'une des mesures suivantes :
Réorienter ou repositionner l'antenne réceptrice Augmenter la séparation entre le matériel et le récepteur.
Connecter le matériel à une sortie sur un circuit différent de celui sur lequel le récepteur est connecté.
Contacter le revendeur ou un technicien radio/TV expérimenté pour une assistance.
Énoncé FCC sur l’exposition aux radiations RF :
Cet équipement est conforme aux réglementations FCC d’exposition aux radiations définies pour un environnement non
contrôlé. Les utilisateurs suivront les instructions d’exploitation spécifiques pour répondre aux exigences de conformité
sur l’exposition aux RF. L’antenne utilisée pour cet appareil ne doit pas fonctionner en même temps qu’une autre antenne
ou émetteur, sauf s'il y a conformité avec les procédures FCC des produits multi-émetteurs.
Précautions FCC
Tout changement ou modification apporté au matériel qui n’aurait pas été approuvé par le responsable de la conformité
pourrait invalider le droit de l’utilisateur à faire fonctionner ce matériel.
Déclaration de conformité CE
Ce produit porte un marquage CE, conformément aux dispositions de la directive R&TTE (99/5/CE). Sena déclare par la
présente que ce produit est conforme aux exigences principales et autres dispositions correspondantes de la directive
1999/5/CE. Pour plus d’informations, veuillez consulter le site www.senabluetooth.fr. Veuillez noter que ce produit utilise
des bandes de radio fréquence non uniformisées au sein de l’Union Européenne. Au sein de l’Union Européenne, ce

produit est destiné à être utilisé en Autriche, Belgique, Danemark, Finlande, France, Allemagne, Grèce, Irlande, Italie,
Luxembourg, Pays-Bas, Portugal, Espagne, Suède et Royaume-Uni et au sein de l’AELE, en Islande, Norvège et Suisse.
Déclaration de conformité IC (Industrie Canada)
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes :
(1) Cet appareil ne doit pas créer d'interférences.
(2) Cet appareil doit accepter toutes les interférences reçues, y compris celles qui pourraient entraver son bon
fonctionnement.
Licence Bluetooth
La marque et les logos Bluetooth® sont la propriété de Bluetooth SIG, Inc et toute utilisation de ces marques par Sena
s'effectue sous licence. D’autres marques et appellations commerciales sont celles de leurs propriétaires respectifs. Le
produit est conforme à et suit la spécification Bluetooth® 3.0 et a réussi tous les tests d'interopérabilité mentionnés dans
la spécification Bluetooth® . Cependant, l'interopérabilité entre l'appareil et d'autres produits Bluetooth® n'est pas garantie.
WEEE(DEEE:Déchets d'équipements électriques et électroniques)
Le symbole poubelle barrée figurant sur le produit, la documentation ou l’emballage signifie que tous les produits
électriques et électroniques, les batteries et les accumulateurs doivent etre conduits en fin de vie dans une structure de
récupération et de recyclage séparée. Cette exigence s’applique à l’Union Européenne mais aussi aux autres pays o
des systèmes de récupération et de recyclage séparés existent. Pour prévenir toutes les conséquences possibles pour
l’environnement ou la santé d’une élimination de déchets non con- trolée, veuillez ne pas considérer ces produits comme
des déchets mé- nagers, mais vous rendre dans une structure de récupération officielle pour le recyclage.
INFORMATIONS SUR LA SCURIT
Veuillez vous assurer que le produit est utilisé de manière adéquate en respectant les avertissements et précautions
énumérés ci-dessous pour éviter tout risque et/ou dommage matériel.
Rangement du produit et manipulation
Garder le produit à l'abri de la poussière. Cela pourrait endommager les pièces mécaniques et électroniques du produit.
Ne pas ranger le produit dans des zones chaudes car cela pourrait réduire la durée de vie des appareils électroniques,
endommager la batterie et/ou faire fondre les pièces en plastique du produit.
Ne pas stocker l'appareil dans des zones froides. Des changements de températures brusques peuvent former de la
condensation et endommager les circuits électroniques. Ne pas nettoyer le produit avec des solvants de nettoyage, des
produits chimiques toxiques ou des détergents puissants car cela pourrait endommager le produit.