Senco FN65DA User manual
Employer must enforce compliance
with the safety warnings and all
other instructions which accompany
this tool as shipped from the
manufacturer.
Keep this manual available for use
by all people assigned to the use of
this tool.
For personal safety and proper
operation of this tool, read and
understand all of these instructions
carefully.
2
Employer’s Responsibilities................................................. 2
Safety Warnings .................................................................. 3
Functional Description....................................................... 14
Tool Operation ................................................................... 16
Maintenance...................................................................... 22
Battery Charger Label Reference...................................... 23
Battery Specications........................................................ 23
Charger Specications ...................................................... 23
Technical Specications .................................................... 24
Fastener Specications ..................................................... 25
Accessories ....................................................................... 26
Troubleshooting................................................................. 26
Limited Warranty................................................................ 28
instructions. Failure to follow the
warnings and instructions may
result in electric shock, re and/or
serious personal injury.
-
The
term "power tool" in the warnings
refers to your mains-operated
(corded) power tool or battery-oper-
ated (cordless) power tool.
lit. Cluttered or dark areas invite
accidents.
-
Power tools
create sparks which may ignite the
dust or fumes.
tool. Distractions can cause you to
lose control.
Unmodied plugs and
matching outlets will reduce risk of
electric shock.
-
There is an increased
risk of electric shock if your body is
earthed or grounded.
3
General Safety Rules
rain or wet conditions. Water
entering a power tool will increase
the risk of electric shock.
Damaged
or entangled cords increase the risk
of electric shock.
outdoors, use an extension cord
Use
of a cord suitable for outdoor use
reduces the risk of electric shock.
use a residual current device
Use of
an RCD reduces the risk of electric
shock.
RX
-
tion. A moment of inattention while
operating power tools may result in
serious personal injury.
-
-
tion. Protective equipment such as
dust mask, no-skid safety shoes,
hard hat, or hearing protection
used for appropriate conditions will
reduce personal injuries.
Prevent unintentional start-
tool. Carrying power tools with your
nger on the switch or energising
power tools that have the switch on
invites accidents.
4
tool on. A wrench or a key left
attached to a rotating part of the
power tool may result in personal
injury.
This enables better control of the
power tool in unexpected situations.
Loose
clothes, jewelry, or long hair can be
caught in moving parts.
-
erly used. Use of dust collection
can reduce dust-related hazards.
The correct power tool
will do the job better and safer at
the rate for which it is designed.
Any power tool that cannot be
controlled with the switch is danger-
ous and must be repaired.
-
Such preventive
safety measures reduce the risk of
starting the power tool accidentally.
5
-
Power
tools are dangerous in the hands of
untrained users.
-
Many accidents are
caused by poorly maintained power
tools.
clean. Properly maintained cutting
tools with sharp cutting edges are
less likely to bind and are easier to
control.
Brand
X
-
Use of the power tool
for operations different from those
intended could result in a hazard-
ous situation.
A
charger that is suitable for one type
of battery pack may create a risk of
re when used with another battery
pack.
Brand X
-
Use of any other battery packs may
create a risk of injury and re.
Shorting the
battery terminals together may
cause burns or a re.
6
7
SOAP
VINEGAR LEMON
JUICE
-
Liquid ejected
from the battery may cause irrita-
tion or burns.
Authorized
Service Center
Service
-
This will ensure that
the safety of the power tool is
maintained.
Careless handling of the
tacker can result in unexpected r-
ing of fasteners and personal injury.
Unex-
pected triggering will discharge the
fastener causing an injury.
If the tool is not
in contact with the workpiece, the
fastener may be deected away
from your target.
While removing
a jammed fastener, the tacker may
be accidentally activated if it is
plugged in.
The mecha-
nism may be under compression
and the fastener may be forcefully
discharged while attempting to free
a jammed condition.
8
-
It is not
designed for electric cable installa-
tion and may damage the insulation
of electric cables thereby causing
electric shock or re hazards.
A battery short can cause a large
current ow, overheating, possible
burns and even a breakdown.
Do not touch the terminals with
any conductive material.
Avoid storing battery cartridge
in a container with other metal
objects such as nails, coins, etc.
Do not expose battery cartridge
to water or rain.
Consecutive charging may cause
overheating. If you need to re-
charge batteries consecutively, wait
about 15 minutes for the charger
to cool.
Fusion
To prevent eye injuries, always
wear OSHA required "Z87" safety
glasses with permanently attached
rigid, hard plastic side shields.
These safety glasses must have
"Z87" printed or stamped on them.
Be sure everyone in your work area
is wearing the same type of safety
glasses.
The Fusion tool is charged with
compressed air in a factory sealed
chamber. DO NOT attempt to open
the air chamber supported within
the tool housing.
The driver assembly contains no
user-serviceable parts. Major com-
ponents such as the piston/driver
assembly, gearbox, piston stop and
guide body are all part of the drive
assembly.
Deliberate tampering with the drive
assembly may result in the release
of the driver.
Any repair or upgrade requiring
access to the pressure chamber
should be handled by an authorized
Senco dealer or service center.
9
Disconnect tool from battery when:
Outside of the operator's
supervision or control.
Performing maintenance or
repair
Clearing a jam
Moving the tool to a new
location
With battery disconnected, make
daily inspection to assure free
movement of workpiece contact
element and trigger. Do not use
tool if workpiece contact element or
trigger sticks or binds.
Always remove nger from trigger
when not driving fasteners. Never
carry the tool with nger on or un-
der trigger. Tool will eject a fastener
if the workpiece contact element is
bumped and the trigger is pulled.
Drive fasteners into work surface
only; never into materials too hard
to penetrate.
Do not drive fasteners on top of
other fasteners or with the tool at
too steep of an angle; the fasteners
can ricochet and hurt someone.
When using tool, care should be
taken due to possibility of tool
recoil after a fastener is driven. If
workpiece contact element is un-
intentionally allowed to re-contact
work surface following a recoil, an
unwanted fastener may be driven.
Therefore, allow tool to recoil
completely off work surface after
a fastener is driven to avoid this
condition. Do not push workpiece
contact element on work surface
until a second fastener is desired.
Do not drive fasteners close to
the edge of the work surface. The
workpiece is likely to split and the
fastener could y or ricochet and hit
someone.
Never use any part of the tool
(i.e., the cap or mainbody ) as a
hammer. The tool may activate or
become damaged and result in an
unsafe condition.
Keep hands and other body parts
away from the area shown in the
circle to avoid possible injury during
operation.
(1) Read and understand tool labels and manual. Failure to follow warnings could result in
DEATH or SERIOUS INJURY. (2) Operators and others in work area MUST wear safety
glasses with side shields. (3) Keep fingers AWAY from trigger when not driving fasteners
to avoid accidental firing. (4) Choice of triggering mechanisms is important. Check manual for
triggering instructions. (5) NEVER point tool at yourself or others in work area. Always point tool
away when connecting battery. (6) Do not alter or remove trigger or safety.
Do not use tool without Danger
Label on tool. If label is missing,
damaged or unreadable, contact
your SENCO representative to
obtain a new label at no cost.
manual
» Lea el manual
de la herra-
mienta
Read and understand tool labels
and manual. Failure to follow
warnings could result in DEATH or
SERIOUS INJURY.
Operators and others in work area
MUST wear safety glasses with
side shields.
Keep ngers AWAY from trigger
when not driving fasteners, to avoid
accidental ring.
Choice of triggering method is
important. -
Never point tool at yourself or oth-
ers in work area.
» Use protección
ocular
-
» Lesiones perso-
nales
» Blessures
Holding the work by hand or
against your body is unstable and
may lead to loss of control.
10
Battery Use
-
Do not expose charger to water,
rain, or snow.
Use indoors.
Use of an attachment not recom-
mended or sold by the battery
charger manufacturer may result in
a risk of re, electric shock, or injury
to persons.
To reduce risk of damage to electric
plug and cord, pull by plug rather
than cord when disconnecting
charger.
Make sure cord is located so that it
will not be stepped on, tripped over,
or otherwise subjected to damage
or stress.
11
25 50 100 150
16 16 16 14
7,5 15 30 45
16 16 16 14
7,5 15 30 45
16 16 16 14
An extension cord should not be
used unless absolutely necessary.
Use of improper extension cord
could result in a risk of re and
electric shock.
If extension cord must be used,
make sure:
That pins on plug of extension
cord are the same number, size,
and shape as those of plug on
charger;
That extension cord is properly
wired and in good electrical
condition; and
That wire size is at least as
large as the one specied in the
table.
Do not operate charger with dam-
aged cord or plug. If damaged,
have replaced immediately by a
qualied serviceman.
Do not operate charger if it has re-
ceived a sharp blow, been dropped,
or otherwise damaged in any way;
take it to a SENCO Authorized
Service Center.
Do not disassemble charger or bat-
tery cartridge; take it to a SENCO
Authorized Service Center when
service or repair is required. Incor-
rect reassembly may result in a risk
of electric shock or re.
To reduce risk of electric shock,
unplug charger from outlet before
attempting any maintenance or
cleaning.
Do not charge battery cartridge
when temperature is BELOW 0˚C
(32˚F) or ABOVE 40˚C (104˚F).
12
13
Do not attempt to use a step-up
transformer, an engine generator or
DC power receptacle.
Do not recharge non-rechargeable
batteries.
Do not allow anything to cover or
clog the charger vents.
113˚F
45˚C
Do not store the tool and battery
cartridge in locations where the
temperature may reach or exceed
45˚C (113˚ F).
Do not incinerate the battery car-
tridge even if it is severly damaged
or is completely worn out. The bat-
tery cartridge can explode in a re.
Never attempt to connect two (2)
chargers together.
This appliance is not intended for
use by young children or inrm
persons unless they have been
adequately supervised by a respon-
sible person to ensure that they do
not play with the appliance.
This appliance is not intended for
use by persons (including children)
with reduced physical, sensory
or mental capabilities, or lack of
experience and knowledge, unless
they have been given supervision
or instruction concerning use of the
appliance by a person responsible
for their safety. Children should be
supervised to ensure that they do
not play with the appliance.
Angled Tool
1
2
3
4
5
6
7
8
➊ On/Off and Selective Actuation
Button
➋Depth of drive control
➌ Workpiece Illumination/
Status Indicator
➍Workpiece contact (safety)
element
➎Feeder shoe
➏ Trigger / On Switch
➐Belt Hook
➑Battery Pack
CordlessFinish
TM
41
Insert strip of nails into rear of
magazine.
Use only genuine SENCO
fasteners (see Fastener
Specications).
Pull feeder shoe back.
`
Push Button on feeder shoe to
release feeder from strip. Pull
fastener strip out past sheet metal
nail detainer.
14
Straight Tool
1
2
34
5
6
7
8
➊ On/Off and Selective Actuation
Button
➋Depth of drive control
➌ Workpiece Illumination/
Status Indicator
➍Workpiece contact (safety)
element
➎Magazine Latch
➏ Trigger/On Switch
➐Belt Hook
➑Battery Pack
Pull magazine latch back to open
access door. Load strip of fasten-
ers with points resting on fastener
guide and then push the door back
toward the front of the tool. An
audible click will indicate that the
strip is properly loaded.
`
Pull magazine latch back to open
access door. Grasp fastener strip
and remove.
15
Read section titled “Safety Warn-
ings,” before using tool.
Li-ion
For best results, charge new bat-
tery before using. (see “To Charge
Battery” page 20).
» Indicator LED
OFF
» LED indicador–
Apagado
» Voyant DEL–
éteint
The tool should be switched off
when not in use. Hold down either
side of the selector switch for 1
second to turn the tool off. If left on,
the tool will automatically turn off
after 35 minutes.
All Fusion tools are equipped with
selective-actuation triggering. This
allows the user to choose between
the following modes of operation:
» Indicator LED
ON – Flash-
ing
» LED indicador–
Encendido y
titilando
» Voyant DEL–
clignotant
Pressing the side of the selector
switch toward the symbol (as
shown) for 0.5 sec. will turn the tool
on in contact-actuation mode. This
is indicated by the ashing green
LED of the selector switch.
» Indicator LED
ON Solid
» LED indicador–
En modo
secuencial
sólido
» Voyant DEL–
non cligno-
tant
Pressing the side of the selector
switch toward the symbol (as
shown) for 0.5 sec. will turn the
tool on in sequential mode. This is
indicated by the solid green LED of
the selector switch.
16
17
In the “contact-actuation” mode,
nails can be driven in two ways:
3
2
1
AA The rst way:
①Press the side of the
selector switch. This will be in-
dicated by the ashing green
LED on the selector switch.
②Press the workpiece contact
(safety) element against the
work surface.
③Pull the trigger and the fas-
tener is driven.
2
3
1
B
BThe second way:
①Press the side of the se-
lector switch for 0.5 seconds.
This will be indicated by the
ashing green LED on the
selector switch.
②Pull trigger.
③Depress workpiece contact
element against work surface
and drive a fastener.
This mode of operation is preferred
when you desire high production,
rapid fastener placement.
2
3
1
In the “sequential-actuation” mode,
nails can only be driven one way:
①Press the side of the
selector switch. This will be
indicated by the solid green
LED on the selector switch.
②Position workpiece contact
(safety) element against work
surface and depress the
safety.
③Pull trigger to turn on the mo-
tor and drive a fastener.
This mode of operation is helpful
when you require precise fastener
placement.
i
The Fusion tool may retract the
driver partially when the battery
charge is very low. if this happens,
place a freshly charged battery
on the tool, depress the safety
and trigger to allow it to automati-
cally adjust to position the driver
correctly. The self adjustment will
sound like a series of short pulses;
this is normal and it is not caused
by any defect in the tool.
Once the tool resets, it will function
normally.
18
This tool is equipped with a dual-
purpose light on the nosepiece.
The light will indicate that the
electronic controls are energized
while providing illumination of the
workpiece in low light situations.
The light will ash three times when
the selection switch is switched to
either sequential or contact actua-
tion. This lets the user know that
the tool is ready to re a fastener.
The light will remain on for ten
seconds when the trigger is pulled
or the work contact element is
depressed.
When the tool is in the
sequential mode, a fastener
cannot be driven by pulling the
trigger before activating the
work piece contact element.
When the tool is in contact
actuation mode, if the operator
holds the trigger on for more
than 3 seconds, the light will
go out and the trigger must be
released to start over.
6
39
12 This tool is equipped with an elec-
tronic “Time-Out” feature. This tool
will temporarily be disabled under
any of the following conditions:
①Workpiece contact element is
depressed against the work
piece, but the trigger is not
pressed within approximately
10 seconds.
②Trigger is pressed, but work
piece contact element is not
depressed within approxi-
mately 3 seconds. (Contact-
Actuation mode only.)
Simply release trigger and
release workpiece contact
element to resume normal
operation.
Ï
-
This tool is equipped with depth-
of-drive dial. Turning the dial to the
right will countersink the fastener,
turning the dial to the left will leave
the fastener up or raised. Drive a
fastener into a scrap piece of wood
to test depth.
1
2
19
This tool is equipped with an
adjustable belt hook. Remove the
knurled fastener to raise or lower
the hook. Switch the position of the
mounting plate on the opposite side
for left-handed operators.
Whenever possible, hold the tool at
a right angle to the work surface.
» Indicator LED
OFF
» LED indicador–
Apagado
» Voyant DEL–
éteint
Always turn the tool off before stor-
ing. As an added protection feature,
the tool will automatically turn off
35 minutes after the last activation.
Turn the tool off by depressing
the selector switch towards either
mode symbol for approximately 1
second, then remove battery.
Wear safety glasses when opening
the E-Z clear latch.
Release the feeder shoe and slide
it forward. Remove fasteners from
the tool.
Release E-Z Clear latch and pull
magazine away. Magazine will
completely disengage.
Pull magazine door latch back to
reveal fastener strip.
Remove strip.
Remove jammed fastener. Attach
the magazine and latch.
Remember! The Fusion tool is
charged with compressed air in a
factory sealed chamber.
Do not tamper with the drive as-
sembly.
Place battery pack in charger. Align
raised ribs on battery pack with
groove in charger.
Li-ion
Press down on battery pack to
be sure contacts on battery pack
engage properly with contacts in
charger.
When properly connected, red light
will turn on. Red light indicates fast
charging mode.
Authorized
Service
Center
Red and green light ashing
indicates defective battery pack.
Return battery pack to your nearest
SENCO Authorized Service Center
for inspection or replacement.
Flashing Red indicates an over-
heated battery. Charging will begin
after battery cools.
Solid red indicates that the battery
is charging.
When battery pack is fully charged,
the red light will turn off and the
green light will turn on.
20
Other manuals for FN65DA
1
This manual suits for next models
3
Table of contents
Other Senco Nail Gun manuals
Senco
Senco XtremePro SCN60XP User manual
Senco
Senco JoistPro 150 User manual
Senco
Senco FramePro 602 User manual
Senco
Senco ISANTA GT60i-NN User manual
Senco
Senco SN902XP User manual
Senco
Senco Nail Gun User manual
Senco
Senco MINI HAND NAILER PC1195 User manual
Senco
Senco PalletPro 57 User manual
Senco
Senco FinishPro XtremePro 25 XP User manual
Senco
Senco FinishPro 41 XP User manual
Senco
Senco TN41P1P User manual
Senco
Senco FinishPro 41 XP User manual
Senco
Senco SHS50XP-N User manual
Senco
Senco SN325+ User manual
Senco
Senco SGT90i User manual
Senco
Senco A10 User manual
Senco
Senco FN65DA User manual
Senco
Senco JoistPro 150XP User manual
Senco
Senco SN70XP User manual
Senco
Senco FramePro 700XL User manual
Popular Nail Gun manuals by other brands
Powernail
Powernail 101R Operation and maintenance manual
Iron Horse
Iron Horse IH-HF3N1 Set up and operation guide
Central Pneumatic
Central Pneumatic Contractor 97524 Assembly and operating instructions
Central Pneumatic
Central Pneumatic 68027 user manual
Central Pneumatic
Central Pneumatic 94446 Assembly and operating instructions
Central Pneumatic
Central Pneumatic 92917 Set up and operating instructions