Seville Classics airLIFT OFF65991 User manual

SC0
SC1
SC2
SC3
R-2
R-3
HOT
R-5
Error Code List
Code
Action
Self-Check Fail - Standby Mode Error
Self-Check Fail - Main Power Error
Self-Check Fail - Save Memory Error
Self-Check Fail - Sensor Error
Table Tilt Alert
Re-plug in the power cable. If the alert does not clear,
please contact customer service.
Re-plug in the power cable. If the alert does not clear,
please contact customer service.
Re-plug in the power cable. If the alert does not clear,
please contact customer service.
Re-plug in the power cable. If the alert does not clear,
please contact customer service.
The desk will run in the opposite direction for about 2"
automatically, then the alert will clear.
Sync Failure
Overheat Protection
Control system
malfunction
Reset the desk, refer to page 10 for instructions on how to
reset the desk.
Let the motors cool down for 18 minutes.
Check the connection of the power cable and LED control panel,
refer to image on page 8.
R-6
RST
EX0
EX1
EX2
EX3
EX4
EX5
EX6
EX7
Voltage irregularity
Not reset completely
Driver Short-Circuit
Re-plug in the power supply. If the alert does not clear,
contact customer service.
Remove some weight from the desk, then the alert will clear
after 20 seconds.
Check the connection of motor cable, refer to image on page 8.
Please contact customer service.
Over-Load Protection
Motor Phase Failure
Moving Direction Error
Contact customer service.
The desk will run in the opposite direction for about 2"
automatically, then the alert will clear.
Contact customer service.
Contact customer service.
Motor wire not connected
Mechanical Malfunction
Anti-collision
Motor Stalling Alarm
Reset the desk, refer to page 10 for instructions on how to
reset the desk.
Meaning
airLIFT Electric Tempered Glass Height Adjustable Desk
(Model No. OFF65991, OFF65992)
*NOTE: We recommend using TWO people to assemble the desk.
Check the connection between motor cable and the
LED control panel, refer to image on page 8.
Get help with assembly and report damaged or missing parts.
Email:
[email protected]
Telephone:
1 [phone]
Hours (M-F): 8:30 AM - 4:30 PM (PST)

ASSEMBLY INSTRUCTIONS
WARNING: Desk Maximum Loading Capacity is 176 lbs (80 kgs)
airLIFT Electric Tempered Glass Height Adjustable Desk
Model No. OFF65991 (Black), OFF65992 (White)
48 in. W x 24 in. D x 28 ~ 47in. H (1.21m x 0.61 m x 0.71 ~ 1.19 m)
SC221207
USER MANUAL
KEEP FOR FUTURE REFERENCE.

Safety Instructions
FAILURE TO COMPLY WITH OR OBSERVE ALL ASSEMBLY, SAFETY AND
OPERATING INSTRUCTIONS AND WARNINGS REGARDING THE USE OF THIS
PRODUCT MAY RESULT IN SERIOUS BODILY INJURY
The desk MUST be RESET before first use.
Read the RESET portion prior to operation (page 10).
•Read and understand this manual before attempting to install or operate.
•Assure that everyone who uses this product is informed of the contents of this manual. This is the
responsibility of the Purchaser.
•Not intended for use by young children or for those persons who require supervision.
•Do not open any of the components – legs or LED Control Panel. There is a risk of electric shock.
•Assemble desk on a flat and level surface.
Use & Liability
Safe use of this product is possible only when the operating instructions are read completely and the
instructions contained are strictly observed. Persons who do not have the necessary experience or
knowledge of this product must not use the product. Persons with reduced physical or mental abilities
should not use this product, unless they are under supervision or they have been thoroughly
instructed in the use of the apparatus by a person who is responsible for the safety of these
persons. Children should be closely supervised to ensure that they do not play with this product.
Before You Begin
Layout all components and hardware. Visually examine and make sure components are free of damage. If
there is visual damage to any component, it must not be installed.
Two people are needed to turn or move the desk and some of it’s components. When moving or turning the
assembled desk, grab the legs, not the desk top.
Make sure to assemble on a soft and non-abrasive surface to avoid scratches.
Check all connections and cables. Make sure the desk is connected to a power outlet.
If the LED Control Panel makes unusual noises or emits an odor, switch power off immediately.
Get help with assembly and report damaged or missing parts.
Email: Supp[email protected]
Telephone: [phone]
Hours (M-F): 8:30 AM - 4:30 PM (PST)
1

#2
#3
#1
#74
#75
#76
Get help with assembly and report damaged or missing parts.
Email: Supp[email protected]
Telephone: [phone]
Hours (M-F): 8:30 AM - 4:30 PM (PST)
#77
#6-C
#8
2
Quick Setup Diagram
Setup should take about 15 minutes to complete. All required tools are
included. Keep the top frame in the box during assembly to protect it from
scratches.

Please check the parts carefully according to the parts list. If you are missing any parts, please contact our customer service
department.
PARTS LIST
(#3) Bracket x 2 PCS (#8) Feet x 2 PCS
(#1) Top Frame x 1 PC (#2) Legs/Beam x 1 PC
Get help with assembly and report damaged or missing parts.
Email: Supp[email protected]
Telephone:
1 [phone]
(#7-A) Drawer Mat x 1 PC (#6-C) Leveling feet x 4 PCS
(#75) Screw (M6 x 14L) x 4 PCS (#76) Screw (M6 x 35L) x 2 PCS
(#11) Power Cable x 1 PC (#74) Screw (M6 x 10L) x 4 PCS
Telephone:
1 [phone]
Hours (M-F): 8:30 AM - 4:30 PM (PST)
3

(#77) Screw (M6 x 20L) x 8 PCS (#78) Hex Key x 1 PC
PARTS LIST
Please check the parts carefully according to the parts list. If you are missing any parts, please contact our customer service
department.
(#73) Cable Tie x 2 PCS
Get help with assembly and report damaged or missing parts.
Email: Supp[email protected]
Telephone: [phone]
Hours
(M-F)
:
8:30 AM - 4:30 PM (PST)
Hours
(M-F)
:
8:30 AM - 4:30 PM (PST)
4

Step 1: Remove Legs/Beam (#2) from the
box
Take out the Legs/Beam (#2) and move to
a nearby worktable. Note that the center
beam will be connected to the base of the
Top Frame (#1) later in this guide. The side
that features the motor is the right side.
TOP
#2
Get help with assembly and report damaged or missing parts.
Email: [email protected]
Step 2: Install Bracket (#3)
Place bracket (#3) to each end of the
legs located on the Legs/Beam (#2),
align the screw holes and use 4
pieces of the M6 x 10L screw (#74)
using the Hex Key (#78) to tighten.
As displayed in the left image.
#2
#3
#74
Telephone: [phone]
Hours (M-F): 8:30 AM - 4:30 PM (PST)
5
airLIFT Electric Tempered Glass Height Adjustable Desk
(Model No. OFF65991, OFF65992)
*NOTE: We recommend using TWO people to assemble the desk.
#78
Motor

Step 3: Remove Top Frame (#1)
from Box
Open the package, take out the Top Frame
(#1) from the box, this item is heavy so we
recommend 2 people for this step.
Identify the front side from the back, note
the drawer will be facing the front.
Back
Front
Get help with assembly and report damaged or missing parts.
Email: [email protected]
Telephone:
1 [phone]
Step 4: Install Leg/Beam (#2) on the
Top frame (#1).
1. Place the Leg/Beam (#2) on the Top
Frame (#1), and align the screw holes of
the center beam to the corresponding
ones, using 2 pieces M6 x 35L screws
(#76) to tighten. DO NOT fully tighten
the screws yet.
2. Align the screw holes on the end of
each side of the Leg/Beam (#2) with Top
Frame (#1), use 4 pieces M6 x 14L
screws (#75) to tighten. Tighten all
screws fully. Refer to the image on the
left.
Note: we recommend using 2 people for
this step.
Back
Front
#1
#2
#75
#76
Telephone:
1 [phone]
Hours (M-F): 8:30 AM - 4:30 PM (PST)
6
airLIFT Electric Tempered Glass Height Adjustable Desk
(Model No. OFF65991, OFF65992)
*NOTE: We recommend using TWO people to assemble the desk.
#1

Step 5: Install the Feet (#8)
Use 8 pieces M6 x 20L screws (#77) to
install the Feet (#8) on the Leg/Beam
(#2).
Note: Please refer to the label on both
feet to identify the front side of each
foot.
Front
#8
#77
#2
Get help with assembly and report damaged or missing parts.
Step 6: Install the Leveling Feet (#6-C).
Take 4 pieces of Leveling Feet (#6-C)
and place 2 pieces on each
corresponding location on the Feet
(#8).
Then fasten them in place by turning
them in a clockwise rotation.
#6-C
#2
Email: [email protected]
Telephone: [phone]
Hours (M-F): 8:30 AM - 4:30 PM (PST)
7
airLIFT Electric Tempered Glass Height Adjustable Desk
(Model No. OFF65991, OFF65992)
*NOTE: We recommend using TWO people to assemble the desk.
#8

Get help with assembly and report damaged or missing parts.
Step 8: Insert Drawer Mat (#7-A)
Using 2 people flip the desk back
over on its legs.
Place the drawer mat (#7-A)
inside the drawer
compartment.
#7-A
Get help with assembly and report damaged or missing parts.
Email: [email protected]
Telephone: [phone]
Hours (M-F): 8:30 AM - 4:30 PM (PST)
8
Power Cable
Port
Motor Cable Port
Motor Cable
airLIFT Electric Tempered Glass Height Adjustable Desk
(Model No. OFF65991, OFF65992)
*NOTE: We recommend using TWO people to assemble the desk.
Motor Cable Port
Step 7: Connect Motor Cable
Plug in the Motor Cable from leg
beam to the LED Control Panel as
displayed in left figure.
LED Control Panel
Power Cable

LED Control Panel
Note: Desk must be RESET before the first use.
Get help with assembly and report damaged or missing parts.
Power ON the desk：
When the desk is plugged in, you will hear a "Beep" sound, then the LED
control panel will show the current height of the desk.
MEMORY 1/2/3 SAVE MEMORY LED DISPLAY UP/DOWN ARROW
Get help with assembly and report damaged or missing parts.
Email: [email protected]
Telephone: [phone]
Hours (M-F): 8:30 AM - 4:30 PM (PST)
9
airLIFT Electric Tempered Glass Height Adjustable Desk
(Model No. OFF65991, OFF65992)
*NOTE: We recommend using TWO people to assemble the desk.

How to Save the Height in Memory
There are 3 available memory heights you can save - 1, 2 & 3. Adjust the desk to your desired height and
press the “M” button to display “S-“. While "S" is flashing, select any of 1, 2 or 3 number button. When a
memory is saved, you will hear “beep-beep” sound. By repeating the same steps, you can save or override an
old saved memory with a new height.
Press and HOLD the button until the unit reaches the lowest height. Continue to press and HOLD for
about 5 seconds until you see a number (ie. 28) on the display AFTER it shows “rst” and makes a “beep-beep”
sound, then release.
Press and HOLD either the or
to adjust to your desired height of the desk.
Post Setup Quick Start Instructions
How to Reset
How to Adjust the Height
Get help with assembly and report damaged or missing parts.
Email: Supp[email protected]
Telephone: [phone]
Hours
(M-F)
:
8:30 AM - 4:30 PM (PST)
HoHow to Low to Lockck/Unlo/Unlockck the LED Control Panel
First adjust the desk height to your desired lock height. Then press and HOLD the
and
together for about 5 seconds until “Loc” is displayed. At this moment, the LED Control Panel is locked and the
buttons
desk height can’t be adjusted. In order to unlock, press and HOLD the and
together for about 5 seconds until a number (previously locked height) is displayed.
10
airLIFT Electric Tempered Glass Height Adjustable Desk
(Model No. OFF65991, OFF65992)
*NOTE: We recommend using TWO people to assemble the desk.
USB-A Port
USB-C Fast Charge Port
Use Only USB-A
Cable (left image)
for USB-A Port on
Desk.
Use USB-C Cable
(Left Image) for
USB-C Port on
Desk
USB Usage Instructions

SC0
SC1
SC2
SC3
R-2
R-3
HOT
R-5
Error Code List
Code
Action
Self-Check Fail - Standby Mode Error
Self-Check Fail - Main Power Error
Self-Check Fail - Save Memory Error
Self-Check Fail - Sensor Error
Table Tilt Alert
Re-plug in the power cable. If the alert does not clear,
please contact customer service.
Re-plug in the power cable. If the alert does not clear,
please contact customer service.
Re-plug in the power cable. If the alert does not clear,
please contact customer service.
Re-plug in the power cable. If the alert does not clear,
please contact customer service.
The desk will run in the opposite direction for about 2"
automatically, then the alert will clear.
Sync Failure
Overheat Protection
Control system
malfunction
Reset the desk, refer to page 10 for instructions on how to
reset the desk.
Let the motors cool down for 18 minutes.
Check the connection of the power cable and LED control panel,
refer to image on page 8.
R-6
RST
EX0
EX1
EX2
EX3
EX4
EX5
EX6
EX7
Voltage irregularity
Not reset completely
Driver Short-Circuit
Re-plug in the power supply. If the alert does not clear,
contact customer service.
Remove some weight from the desk, then the alert will clear
after 20 seconds.
Check the connection of motor cable, refer to image on page 8.
Please contact customer service.
Over-Load Protection
Motor Phase Failure
Moving Direction Error
Contact customer service.
The desk will run in the opposite direction for about 2"
automatically, then the alert will clear.
Contact customer service.
Contact customer service.
Motor wire not connected
Mechanical Malfunction
Anti-collision
Motor Stalling Alarm
Get help with assembly and report damaged or missing parts.
Email: [email protected]
Telephone: [phone]
Hours (M-F): 8:30 AM - 4:30 PM (PST)
11
Reset the desk, refer to page 10 for instructions on how to
reset the desk.
Meaning
airLIFT Electric Tempered Glass Height Adjustable Desk
(Model No. OFF65991, OFF65992)
*NOTE: We recommend using TWO people to assemble the desk.
Check the connection between motor cable and the
LED control panel, refer to image on page 8.

Seville Classics, Inc.
19401 Harborgate Way Torrance, CA 90501 USA
Telephone: [phone] within USA
Fax: [phone]
Hours: 9:00am - 4:30pm (Pacific Standard Time)
E-mail: [email protected]om
Website & Online Store: www.sevilleclassics.com
CONTACT INFORMATION
If you are missing any parts, have any questions, or need additional assistance in assembly, please contact our
bilingual (English and Spanish) customer service department at:
12
NOTE: This equipment has been tested and found to comply with the limits for Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced Radio/TV technician for help