Indiana Furniture Square One 17-3 User manual

800.422.5727 www.IndianaFurniture.com
Square One
Assembly Instructions
17-3
NOTE: Anchoring to floor or wall may require additional tools and hardware. See note at end of instructions.
Tools Needed:
Components: Model Description 17-3
Quantity
17-2424BL Single Block, 24"x24“
(4 Bolts & Nuts Included) 48
17-17596EC End Cap, 96" 4
(2 used vertically, 2 used
horizontally)
17-17597EC End Cap, 97-3/4" 2
(used vertically)
17-17596CP Corner Post, 96" 2
17-17597CP Corner Post, 97-3/4" 2
17-175120HBS Horizontal Beam Spanner, 120" 2
17-LEVKIT Leveler Kit, 2 Levelers 12
A
A
B
B
B
C
C
D
C
E
D
E
12x8x8
17-3 & 17-4 Page 1 of 3
Drill 5mm & 4mm
Allen Keys
Box Level Tape
Measure
Ladder 2 to 3
Installers
6mm Allen Key
Driver Bit

800.422.5727 www.IndianaFurniture.com
80mm bolt
60mm bolt
17mm nut
Cap, Post, or Beam
2
5
Square One
Assembly Instructions
17-3
17-3 & 17-4 Page 2 of 3
12x8x8
Begin by building the configuration 1 block high. To
establish the configuration footprint.
Align the holes in blocks and connect with 2, 80mm
bolts and 2, 17mm nuts.
Fasten the bolt and nut together but do not
over tighten because you will want to align
and firmly tighten upon final setup.
In the bottom row of blocks install the levelers. Use
the 6mm Allen Key Driver Bit to install the threaded
insert into the bottom holes of the block.
It is important that the threaded insert is
installed as close to perpendicular as possible.
Thread the leveler into the insert. Then thread a
17mm nut onto the top of the leveler.
Connect the correct length Corner Posts to a wall
section using the 60mm bolts and the threaded
inserts in the post.
Using a box level to check level, adjust the levelers
on the configuration so they are all touching the
floor.
Install the rest of the blocks using the 80mm bolts
and 17mm nuts until the configuration is built.
1
2
3
4
Box Level Corner Post
Adjust
Levelers
6
5
6
7
17mm nut
Threaded
Insert
Leveler
4
2
2
97-3/4”
5
97-3/4”
96”
96”

800.422.5727 www.IndianaFurniture.com
Square One
Assembly Instructions
17-3
17-3 & 17-4 Page 3 of 3
Install the correct length End Caps using the 60mm
connection bolt.
Using a ladder and an assistant, install the End Caps
and Horizontal Beam Spanners on the top of the unit
using the 60mm bolts.
The Horizontal Beam Spanners will only have
two connection holes at each end.
Once everything is attached, go back and align
components. This may require loosening bolts and
nuts to align. Once adjusted to satisfaction, tighten
hardware to a secure fit.
Your configuration is complete.
If adding Acoustical or Tackable Panels, Acrylic
Inserts, Dry Erase Boards, or TV Mounts, see
individual instructions for installation.
Wall / Floor Anchoring:
Additional support is required for configurations that
are not free standing. Anchoring to the floor, wall,
ceiling, and other furniture will require additional
tools and hardware, not provided by Indiana
Furniture. The installer is responsible for sourcing
hardware and for the installation of support per
building conditions.
8
97-3/4”
97-3/4”
96”
96”
8
9
10
11
12x8x8
11
9
End Cap
Horizontal
Beam
Spanner