Ronbow SIGNATURE NOCE E035112 Assembly instructions

INSTALLATION AND CARE GUIDE
NOCE LED MIRROR
E035112

170615ronbow.eu | ronbow.comINSTALLATION SHEET
1
NOCE LED Mirror
Model : E035112 Designed By: MATTEO THUN & ANTONIO RODRIGUEZ | ITALY
PRE-INSTALLATION
Tools Required
ALL WIRING SHOULD BE DONE BY A QUALIFIED LICENSED ELECTRICIAN.
WARNING: To reduce the risk of electrical shock, shut o power before wiring the cabinet.
CAUTION: Requires 120V 20AMP circuit.
CAUTION: The LED mirror must be wired to a GFI (ground fault interrupter) circuit breaker when used in
bathrooms and all other locations required by the national electric code.
2 self-tap anchors
2 anchor screws
1 set of wall cleats
1 electrical box
3 wire nuts
Materials Included
Materials Required
120VAC
20A GFI
CIRCUIT BREAKER FIELD CONNECTION LED MIRROR CABINET
White = Negative
Green= Ground
Black= Positive
White = Negative
LED
Black= Positive
Green= Ground

170615ronbow.eu | ronbow.comINSTALLATION SHEET
2
NOCE LED Mirror
Model : E035112 Designed By: MATTEO THUN & ANTONIO RODRIGUEZ | ITALY
Figure 2.
Figure 3.
Figure 1.
Step 2:
Step 3:
Fasten the self-tap anchors to the
wall, then place the wall cleat over
them and secure with the
anchor screws.
Determine the ideal location of your
new LED mirror.
Mark the locations for the anchors to
hang the wall cleat.
Step 1:
INSTALLATION
Step 4:
Step 5:
Secure the wall cleat to with the long
screws provided.
Verify the wall cleat is level.
See Figure 2 & 3.
See Figure 1.
Cut an opening in the wall and connect the
electrical wires to the housing.
NOTE: Run electrical wires to the opening.
An electrical box is recommended inside
the opening.
Secure the cleat in the back of the mirror to
the wall cleat. Hide all wires in the opening.

170615ronbow.eu | ronbow.comINSTALLATION SHEET
3
NOCE LED Mirror
Model : E035112 Designed By: MATTEO THUN & ANTONIO RODRIGUEZ | ITALY
Wood Surfaces
Recommended Products
The fine furniture finish of your new vanity, mirror or other bathroom accessories are designed to
protect against normal home use. With proper care, your product will provide years of use and beauty
in your home.
General Care Tips
PRODUCT CARE AND MAINTENANCE
• If a spill occurs, clean and dry the surface immediately as liquid can soak through the surface and cause
greater damage.
• Do not place in direct sunlight. Exposure to sunlight may affect the appearance of your vanity, and the
finish will eventually crack.
• Keep away from direct sources of extreme temperatures as heat, cold or moisture from humidity.
Color changes, or blemishes in the wood can occur if recommended care of is not met. Try to avoid
these extremes.
• Most wood surfaces can be cleaned, or dusted, with any commercial wood cleaning product. For general
cleaning, use a non-abrasive, or lint-free cloth while dusting along the wood grain to preserve the
wood’s chacteristics.
• Pledge Orange Oil, or similar
• Orange-Glo Wood Cleaner
DISCLAIMERS: Wood naturally ages, darkens and changes color over time due to several environmental conditions that may cause materials to vary from their
original color and/or to warp, split or crack. These variations are considered to be the nature of the material in relation to their environmental exposure and may
be significant over a long period of time. The eectiveness of cleaning Ronbow product is dependant on various factors that include sunlight, smoke, moisture,
household cleaners and/or amount of cleaning product used over time. Ronbow cannot guarantee that the above Product Care & Maintenance methods will
eectively clean your product.
• Test cleaning product on small, discrete area prior to applying to entire surface.
• Wipe surfaces frequently with dry, soft, non-abrasive and lint-free towel.
• Do not allow liquids and moisture to accumulate on the surface of products.
• For warranty information, please visit our website at www.ronbow.com or contact the Customer Service
Department at [phone].

170615
40650 Encyclopedia Circle
Fremont, CA 94538
T 510.713.1188
F 510.657.9388 ronbow.eu | ronbow.com