SHANGRI-LA HAMPTON SLHAMPTCDWA User manual

HAMPTON CHEST
OF DRAWERS
SLHAMPTCDWA, SLHAMPTCDBA

COMPONENTS

Hardware
A
(x34)
B
(x34) CΦ6x30 (x32) DΦ4x40 (x16)
EΦ3x12 (x32)
F
(x4)
G
(x4)
H
(x4)
I
(x4) JΦ4x14 (x2)
K
(x2) LΦ4x25 (x3)
MΦ2.5x12 (x26)
N
(x2) OΦ4x30 (x20)
P
(x4)
QΦ3x12 (x8)
R
(x1)

Step 1: Insert A into both ends of part 9. Repeat this step with the other part labelled 9.
A(x4)
Step 2: Insert C into parts labelled 9 then secure 9 with parts labelled 10.Ensuring the
arrows on each Bpiece are pointing to the corresponding Apiece, insert Bpieces into parts
labelled 10 and secure Bto Awith a Phillip head screwdriver (not supplied).
B(x4)
C (x4)
ASSEMBLY
✗
✓
x2

Step 3:
C(x8)
D (x10)
Step 4:
A(x6)
E (x16)

Step 5:
B(x3)
C (x2)
Step 6:
B
(x3)
C
(x2)

Step 7:
C(x4)
D (x4)
Step 8:

Step 9:
A(x4)
J (x2)
K (x2)
L (x3)

Step 10:
B(x4)
C (x4)

Step 11:
M(x26)

Step 12: Align the chest of drawers assembly with where you would like to place it. Mark two
spots on the wall according to the K brackets. Using a drill (not supplied), make holes on the
marked spots. With a hammer (not supplied), secure N through the holes.
Align K on the chest of drawers assembly over N and using a Phillips screwdriver, secure the
Dscrews through both components (K, N).
D(x2)
N (x2)
TOPPLING FURNITURE WARNING:
•It is strongly recommended that this product is permanently fixed to the wall.
•Please seek professional advice if you are in doubt of what fixing device to use.
•Regularly check that anchors are securely maintained.
•Stability of tall items may be affected by thick carpets or uneven floors.
•Do not place unanchored televisions on furniture.
Caution! For your safety when attaching the anchor fixings, please note the following:
Check any electrical wires or plumbing inside the wall before drilling any holes (if you
are unsure, please seek professional advice from a qualified tradesperson).

Step 13: Using a Phillips screwdriver, secure parts 12,13 and 14 with O screws. Connect part
16 to part 14 with one O screw.
Insert A onto part 11. Secure P onto part 11 with Q screws.
Repeat the whole process three more times to create four drawer assemblies.
A(x20)
O (x20)
P (x4)
Q (x8)
x4

Step 14: Slide part 15 onto one drawer assembly. Insert part 11 over parts 12, 13 and 16.
Ensuring the arrows on each Bpiece are pointing to the corresponding Apiece, insert B
pieces into parts labelled 12, 13 and 16 and secure Bto Awith a Phillips head screwdriver.
Repeat this process three more times with the remaining drawer assemblies.
B(x20)
C (x8)
E (x16)
Step 15:
x4

Assembly complete.

Need more information?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com