SHANGRI-LA SLSERENEUWA User manual

SERENGETI
ENTERTAINMENT UNIT
SLSERENEUWA

Failure to follow these basic steps can lead to damage that is not covered by your warranty.
•Read instructions carefully. Ensure no parts are missing.
•Lay out all the components on a soft surface.
•Carefully identify each component, especially those that are similar. The most
common mistake is getting things back to front.
•Do not fully tighten screws (leave slightly loose). When the item is fully assembled,
tighten the screws but do not over tighten.
•Separate and identify each component from the hardware pack and rest each one
in its proper location before fastening.
•Do not, for any reason, use a power tool to assemble this product.
Use of power tools may apply greater than excess force on the
fixtures, causing damage. Warranty is void if power tools have
been used.
•A Phillips head screwdriver (not supplied) is required for assembly.
The user guide enclosed refers to multiple sets of metal slide runners and slide tracks
(pictured above separately).
To avoid any damage to these items during transportation, the slide runners and slide
tracks have been pre-assembled together in pairs. Each pair includes a slide runner and
slide track. Before assembling your new Shangri-La unit, please separate the slide runners
from the slide tracks according to the below instructions.
SAFETY & WARNINGS
Slide Track
Slide runner

Step 1: Extend the slide runners apart from the slide track:
Step 2: Gently press the plastic release lever on the slide runner
while pulling the slide runner and slide track apart from each
other:
Step 3: The slide runner and slide track
should now be separated. repeat these
steps for all remaining pairs of slide runners
and slide tracks:
To adjust your doors to make the gaps more even (optional).
Step 1: Open the door.
Top panel
Door
Side panel

Step 2: Adjust the gap between door and side panel.
Loosen the screw slightly. Adjust the hinge to right position (see step 2a & 2b). then tighten
the screw.
Step 2a: Move the door in Step 2b:Move the door out
Push the hinge back slightly. Pull the hinge forward slightly.
Top panel Top panel
Gap too large
Top panel
Top panel
Door
Side panel
Top panel
Gap too small
Top panel
Door
Side panel
Top panel
Side panel
Door

Step 3:Adjust the gap between two doors.
Loosen or tighten the screw slightly to adjust the gap between the door panels (see step 3a
& step 3b).
Step 3a: Move the door right Step 3b:Move the door left
Turn the screw clockwise a little as
shown to make the gap smaller
Turn the screw counter clockwise a
little as shown to make the gap
bigger.
Door
Top panel
Door
Side panel
Side panel
Top panel
Door Door
Gap too large Gap too small
Top panel
Top panel
Top panel
Side panel
Door

COMPONENTS

No. Dimensions (mm) Qty No. Dimensions (mm) Qty
1 355 x 383 x 15 1 13 364 x 432 x 2.5 2
2 355 x 383 x 15 1 14 151 x 901 x 2.5 1
3 355 x 383 x 15 1 15 60 x 1760 x 15 2
4 355 x 383 x 15 1 16 60 x 313 x 15 2
5 400 x 1800 x 15 1 17 60 x 313 x 15 2
6 383 x 1800 x 15 1 18 175 x 890 x 15 1
7 382 x 892 x 15 1 19 118 x 350 x 12 1
8 80 x 890 x 15 1 20 118 x 350 x 12 1
9 50 x 1796 x 15 1 21 116 x 848 x 12 1
10 50 x 892 x 15 1 22 344 x 857 x 2.5 1
11 317 x 450 x 15 1 23 50 x 335 x 12 2
12 317 x 450 x 15 1

AΦ15x9.6 (x40) BL=35mm (x40) CΦ5.5x38 (x8)
DΦ4x32 (x2) E14" (x2) F14" (x2)
GΦ3.5x12 (x12) H(x12) IΦ3x18 (x12)
J(x4) KΦ4x15 (x16) LΦ4x25 (x6)

Step 1:
BL=35mm (x6)
ASSEMBLY

Step 2:
F14" (x2) GΦ3.5x12 (x6)
DRAWER SLIDE (F X 1) DRAWER SLIDE (F X 1)

Step 3: Use D screws to secure parts as shown. Use a Phillips head screwdriver to secure A
to B for part 18.
AΦ15x9.6 (x2) DΦ4x32 (x2)
Arrow to point in
the direction of
end hole

Step 4:
AΦ15x9.6 (x4)
Arrow to point in
the direction of
end hole

Step 5:
E14" (x2) GΦ3.5x12 (x6)
DRAWER SLIDE (E X 2)

Step 6:
BL=35mm (x6)

Step 7:
BL=35mm (x14)

Step 8:
AΦ15x9.6 (x5)
Arrow to point in
the direction of
end hole

Step 9:
BL=35mm (x6)

Step 10: Repeat this process twice for the parts labelled 15.
BL=35mm (x8)

Step 11:
AΦ15x9.6 (x8)
Arrow to point in
the direction of
end hole