Shark NV642 User manual

S3973 Series
OWNER’S GUIDE
GUIDE D’UTILISATION
MANUAL DEL PROPIETARIO

11-800-798-7398
WHEN USING YOUR SHARK®LIFT-
AWAY®PRO STEAM POCKET®MOP,
BASIC SAFETY PRECAUTIONS SHOULD
ALWAYS BE FOLLOWED, INCLUDING THE
FOLLOWING:
READ ALL INSTRUCTIONS BEFORE USING
YOUR SHARK LIFT-AWAY PRO STEAM
POCKET MOP.
WARNING: DANGER OF SCALDING.
The steam emitted from the Steam Mop
is very hot and may cause scalding.
Please use caution when using the
Steam Mop.
WARNING: KEEP STEAM MOP AWAY
FROM CHILDREN.
POLARIZED PLUG:
This Steam Mop has a polarized plug (one
blade is wider than the other). As a safety
feature, this plug will fit into a polarized outlet
only one way. If the plug does not fit fully
into the outlet, reverse the plug. If it still does
not fit, contact a qualified electrician. Do not
attempt to defeat this safety feature. It is not
recommended to use an extension cord with
this product.
IMPORTANT SAFETY INSTRUCTIONS
For Household Use Only
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR INJURY:
1. When in use never turn the Steam Mop over on
its side or direct steam toward people, pets or
plants.
2. Use the system only for its intended use.
3. DO NOT use for space-heating purposes.
4. DO NOT use outdoors.
5. DO NOT leave the Steam Mop unattended
when plugged in. Always unplug the power cord
from the electrical outlet when not in use and
beforeservicing.
6. DO NOT allow the Steam Mop to be used by
children. Close attention is necessary when
used near children, pets, or plants.
7. Use only as described in this owner’s guide.
8. Use only manufacturer’s recommended
accessories.
9. DO NOT use with damaged cord or plug. If
Steam Mop is not working as it should or
has been dropped, damaged, left outdoors,
or dropped into water, return it to SharkNinja
Operating LLC for examination and repair.
Incorrect reassembly or repair can cause a risk
of electrical shock or injury when the Steam Mop
is used.
10. To protect against a risk of electric shock, DO
NOT immerse the Steam Mop in water or any
other liquids.

2sharkclean.com
English
11. DO NOT handle the plug or Steam Mop with
wet hands or operate it without wearing shoes.
12. DO NOT pull or carry by cord, use cord as
a handle, close a door on cord, or pull cord
around sharp edges or corners. Do not run
Steam Mop over cord. Keep cord away from
heated surfaces.
13. DO NOT unplug by pulling on power cord. To
unplug, grasp the plug not the power cord.
Do not use extension cords or outlets with
inadequate current-carrying capacity.
14. DO NOT put any objects into the the steam
nozzle openings. Discontinue use if the steam
nozzle is blocked.
15. DO NOT put hands or feet under the Steam
Mop. It gets very hot.
16. Use ONLY on flat, horizontal surfaces. DO NOT
use on walls, counters, or windows.
17. DO NOT use on leather, wax-polished furniture,
synthetic fabrics, velvet, or other delicate,
steam-sensitive materials.
18. DO NOT add cleaning solutions, vinegar,
scented perfumes, oils, or any other chemicals
to the water used in the Steam Mop as this
may damage it or make it unsafe for use. If you
live in a hard-water area, we recommend using
distilled water in your Steam Mop.
19. Never leave any Dirt Grip™pad in one spot
while using or storing for any period of
time, as this may damage your surfaces.
20. You can release the Dirt Grip pad after you have
unplugged the Steam Mop and allowed it to
cool.
21. When cleaning the exterior of the Steam Mop,
unplug the power cord from the electrical outlet and
clean the Steam Mop with a dry or damp cloth. Do
not pour water or use alcohol, benzene, or paint
thinner on theSteam Mop.
22. Extreme caution should be exercised when
using the Steam Mop to clean stairs.
23. Never use Steam Mop without the Dirt Grip pad
attached.
24. Keep your work area well lit.
25. Store Steam Mop indoors in a cool, dry place.
26. To avoid circuit overload, do not operate another
appliance on the same socket (circuit) as the
Steam Mop.
27. To avoid scalding injuries, always unplug and
allow the Steam Mop to cool before removing
or changing mop heads, accessories, or Dirt
Grip pads.
WARNING:Your Steam Mop is
designed to clean hard floor surfaces that will
withstand high heat. Do not use on unsealed
wood or unglazed ceramic floors. On surfaces
that have been treated with wax and on some
no-wax floors, the sheen may be removed
by the heat and steam action. It is always
recommended to test an isolated area of the
surface to be cleaned before proceeding. We
also recommend that you check the use and
care instructions from the floor manufacturer.
SAVE THESE INSTRUCTIONS

31-800-798-7398
Thank you for purchasing the Shark®Lift-Away®Pro Steam Pocket®Mop.
This Owner’s Guide is designed to help you get a complete understanding of your new Shark Lift-Away Pro Steam
Pocket Mop. Please read it carefully and keep for future reference.
For a list of what is included with this model, refer to box's top panel.
If you should have a question about your Shark Lift-Away Pro Steam Pocket Mop, please call Shark Customer Service
at 1-800-798-7398.
The Shark Lift-Away Pro Steam Pocket Mop is an amazing solution for deep steam cleaning. Whether you need to battle
tough stains with the Steam Blaster
™
or handle general cleaning and hard floor sanitization*, our next-generation Intelli-
Mop
™
Head and Dirt Grip
™
pads offer the ultimate in versatility and efficiency, making cleaning simple, quick and easy.
* Sanitization studies were conducted under controlled test conditions. Household conditions and results may vary.
With the Intelli-mop head only in SCRUB mode. Not in above floor mode or when using Steam Blaster.
REGISTER YOUR PURCHASE:
registeryourshark.com
1-800-798-7398
RECORD THIS INFORMATION:
Model Number: ____________________________________
Date of Purchase (Keep receipt):_________________________
TECHNICAL SPECIFICATIONS:
Voltage: 120V, 60 Hz
Watts: 1500W
Water Capacity: 300 ml (10.14 oz.)
RECOMMENDED SCHEDULE FOR REPLACING WASHABLE DIRT GRIP™PADS:
Every 3 months
FOR BEST CLEANING PERFORMANCE:
See the Caring for Your Steam Pocket Mop section for more detail. Vacuum or sweep before mopping.

4sharkclean.com
English
Contents
Getting Started............................................................................................... 5
Assembling Your Steam Pocket Mop ............................................................... 7
Using Your Steam Pocket Mop ........................................................................ 8
Intelligent Steam Control®............................................................................... 9
Above-Floor Cleaning ....................................................................................10
Using the Direct Steam Nozzle .......................................................................11
Using the Garment Steamer...........................................................................12
Using the Accessory Hose and the Precision Clean Accessory.........................13
Caring For Your Steam Pocket Mop................................................................14
Ordering Additional Accessories.....................................................................15
Troubleshooting Guide...................................................................................16
Frequently Asked Questions...........................................................................17
Warranty.......................................................................................................18
Thank you for
purchasing
the Shark®
Lift-Away®Pro
Steam Pocket®
Mop.

51-800-798-7398
Getting Started
When assembling your Steam Mop there may be a little water in or around the water tank. This is because we test all
our Steam Mops before you buy them, so you get a quality Shark®Lift-Away®Pro Steam Pocket®Mop.
aSteam Mop Handle
bUpper Cord Wrap
c(1) 6 mm x 54 mm Large Screw*
dLower Cord Wrap
eSteam Mop Body
fRemovable Handheld Steamer
gRelease Button for Handheld Steamer
hSteam Trigger
iSteam Control Panel
jFilling Flask
kMop Head Release Button
lDirt Grip™Pad Release Buttons
mSteam Blaster™Nozzle
nIntelli-Mop™Head
oDirt Grip Pad
*Phillips or flat head screwdriver can be used. Screwdriver not included.
a
b
d
e
j
k
l
m
n
o
f
g
h
i
c

6sharkclean.com
English
HANDHELD ACCESSORIES
DIRECT STEAM NOZZLE
Use steam to break down dirt and hard surfaces and wipe
away grime.
Use 3-to-5-second bursts of steam using the trigger on the
handle unit for best results.
GARMENT STEAMER
WITH BONNET AND BRISTLE FRAME
Ideal for removing wrinkles from clothing and for freshening and
grooming upholstery.
Do not use this tool without the Microfiber Bonnet attached.
ACCESSORY HOSE
For optimal range and mobility when cleaning above-floor
surfaces.
PRECISION CLEAN POCKET ACCESSORY AND PAD
Ideal for small, uneven surfaces, corners, and edges. Do not use
without a Precision Clean Pocket Pad attached.
For a full list of what is included with your Steam Mop, please refer to the inside flap of your box.
CAUTION: Test in a small inconspicuous area and contact your surface manufacturer/installer for
specific information on your surface.

71-800-798-7398
Assembling Your Steam Pocket®Mop
WARNING: Always make sure the Steam Mop is
UNPLUGGED when not in use. Never fill the Steam
Mop or attach the mop head when the Steam Mop
is plugged into an electrical outlet. Unplug from
the electrical outlet and allow to cool before you
fill the mop, or attach or remove the head. To
prolong the life of your Steam Mop, we recommend
using distilled water. Make sure you add only
water to the tank. Chemicals or cleaning solutions
(including vinegar) may damage the Steam Mop
and could be unsafe for you and your family.
STEAM MOP ASSEMBLY
1Screw the mop handle into the Steam Mop body
(screwdriver not included) (fig. 1).
2Slide the Intelli-Mop
™
Head post into the Steam Mop
body. Push until you hear it click securely into place.
(fig. 1) To detach the Intelli-Mop Head, press the
release button on the front of the unit above the head
connection (fig. 1) and slide off.
3To attach the Dirt Grip™pad, spread the pad on
the floor with the pocket side up. Lift the mop and
center the Intelli-Mop Head above the pad, then
press down on the release buttons on the neck of
the steam mop head (fig. 2a). Both sides of the
Intelli-Mop Head will drop open (fig. 2b). Slip the
Intelli-Mop Head’s four corner tabs into the four
corner pockets of the pad (fig. 3 and fig. 4).Gently
press one side of the Intelli-Mop Head to the floor
until that side clicks into place (fig. 5). Repeat on
the other side (fig. 6).
4Open the water tank cap (fig. 7), fill the tank with
water, then replace and tighten the cap. Use the
filling flask and pour water into the tank (fig. 8). Do
not overfill. Replace the cap on the water tank.
fig. 1 fig. 5 fig. 6fig. 4
fig. 7 fig. 8
fig. 3fig. 2b
fig. 2a

8sharkclean.com
English
NOTE: To prolong the life of your Steam Mop, we
recommend using distilled water.
NOTE: Sweep or vacuum your floors prior to
cleaning with your Steam Mop.
1 Twist the upper cord holder to unwrap the power cord
completely (fig. 9). Plug into an electrical outlet.
2 When it's first plugged in, the unit will be in Standby
mode. The 3 lights below the Steam Control Button
will blink to indicate Standby mode.
3To select the steam mode, press the Steam Control
Button once for DUST (1 blue light) twice for MOP (2
blue lights) or three times for SCRUB (3 blue lights).
Pressing a fourth time will place the unit on Standby.
4 Clean your floors with a forward and backward motion.
5 When you need an extra burst of steam to clean
a stuck-on stain, you can use the Steam Blaster™
feature. Flip the head over so that it is behind the
mop body, then tilt the mop handle down. This will
cause the the Steam Blaster (fig. 10) to emit a
concentrated blast of steam onto the stain.
CAUTION: While in Steam Blaster mode, do not
leave stationary for more than one minute.
CAUTION: Do not scrub any one area for an
extended period of time.
IMPORTANT: Make sure you do not use the Shark
®
Lift-Away
®
Pro Steam Pocket
®
Mop without attaching a Dirt
Grip
™
pad and adding water to the water tank first. When you are using the Steam Mop for the first time, it
might take longer than the normal 30 seconds to start steaming.
IMPORTANT: Do not use on unsealed wood or unglazed ceramic floors. On surfaces that have been treated with
wax and on some no-wax floors, the sheen may be removed by the heat and steam action. Test an isolated area
of the surface to be cleaned before proceeding. Check the use and care instructions from the floor manufacturer.
Using Your Steam Pocket®Mop
6To stop the Steam Blaster spray, simply raise the
handle. You can then flip the mop head back into its
original position and continue cleaning.
7When you are done mopping, press the Steam Control
Button until you return to Standby mode .
8 To remove the Dirt Grip pad, simply lift the mop
straight up by the handle until the Intelli-Mop
™
Head is
hanging straight down. Press down on the pad release
buttons on the neck of the mop head (fig 11a), and
both sides of the head will drop open, releasing the
pad (fig 11b).
9 Once the Dirt Grip pad has been rel eased, close the
Intelli-Mop Head. To close, gently p ress one side of
the Intelli-Mop Head to the floor until that side clicks
into place. Repeat on the other side.
10 When the water tank is empty, the Steam Mop will
stop producing steam. You can refill the water tank
at any time as long as the Steam Mop is unplugged.
Follow the water tank filling instructions on page 7.
NOTE: Please wait 2 to 3 minutes for the Steam Mop
to cool off before switching the mop head. Never
leave the Steam Mop with a damp or wet Dirt Grip
pad on any floor for an extended period of time.
fig. 9 fig. 10 fig. 11b
fig. 11a

91-800-798-7398
Intelligent Steam Control®
The Shark®Lift-Away®Pro Steam Pocket®Mop has 3 unique Intelligent Steam Control settings so you can use
the right amount of steam for the cleaning task at hand. See below for tips on when to use each setting.
TO SANITIZE* WITH THE STEAM MOP USING THE INTELLI-MOP™HEAD AND THE DIRT GRIP™PAD:
1Attach a clean Dirt Grip pad to the mop head.
2Plug in the unit and press the Steam Control Button to select the SCRUB Setting.
3Wait 30 seconds for the unit to begin producing steam.
4 Start mopping on an appropriate sealed hard floor surface with a forward and backward motion. After three minutes,
your unit is ready to be used to sanitize.
5Using a forward and backward motion, move the unit over the area you seek to sanitize. Repeat at least 15 times.
* Sanitization studies were conducted under controlled test conditions. Household conditions and results may vary.
With the Intelli-mop head only in SCRUB mode. Not in above floor mode or when using Steam Blaster.
SETTING IDEAL FOR THESE SEALED
SURFACES
RECOMMENDED USAGE
DUST
LIGHT STEAM
Laminate
Hardwood
Marble
Cleaning delicate surfaces
Light cleaning and dusting
Loosening and lifting light dirt
MOP
NORMAL STEAM
Hardwood
Marble
Tile
Stone
Cleaning most surfaces and large areas
Basic, everyday cleaning
Removing spots and smaller messes
Cleaning moderate and heavy-traffic areas
SCRUB
HEAVY STEAM
Hardwood
Marble
Tile
Stone
Deep-cleaning and cleaning hard-to-clean surfaces
Tough cleaning and removing stuck-on messes and stains
Deep-cleaning heavy-traffic areas
Cutting through heavy dirt and grime
Sanitizing* floors
Steam Blaster™For an extra burst of steam, you can use the Steam Blaster feature in DUST, MOP, or SCRUB.
Follow the instructions found on the “Using your Steam Pocket Mop” page.

10sharkclean.com
English
Above-Floor Cleaning
•Remove the Handheld Steamer by pressing on the
release button and pulling away from the cradle.
Be careful to NOT press the steam trigger as you
remove the handheld steamer. (fig. 12)
fig. 12
The Shark®Lift-Away®Pro Steam Pocket®Mop is
designed to clean surfaces that can withstand high heat
and moisture. Do not use on unsealed wood surfaces
(especially antique wood furniture), unglazed ceramic
tile, painted surfaces, or surfaces that have been
treated with wax, oils, varnishes, or shellac. The sheen
may be removed by the heat, steam, and friction of the
cleaning accessories. It is always recommended to test
an isolated area of the surface to be cleaned before
proceeding.
•The Handheld Steamer is automatically set
to SCRUB mode. Squeeze the steam trigger to
activate steam. You may select other steam modes
depending on the accessory and the use.
•With all attachments, control Steam better by using
3-to-5-second bursts of the trigger. This will allow
you to steam longer and with more control.
We also recommend you check the use and care
instructions from the surface manufacturer. When
cleaning finished wood surfaces, use broad, continuous
strokes. To prevent surface damage, avoid focusing
steam or allowing the cleaning accessories to remain
stationary in any one spot.
For a full list of what is included with your Steam Mop, please refer to box's top panel.

11 1-800-798-7398
How to Attach/Detach:
• The Direct Steam Nozzle slides directly on to the handheld steamer. (fig. 13)
• To remove, wait 2 to 3 minutes for the tool to cool, hold the release button and pull the tool away from the unit.
Usage:
• The Direct Steam Nozzle creates direct steam spray to clean hard-to-reach nooks and crannies, flat surfaces, toys
and other places where germs may build up. (fig. 14)
• Spray direct steam and wipe clean with a wet cloth or paper towel.
Cleaning Tips:
• For effective cleaning, hold the steam output nozzle 1 to 2 inches away from the surface you’re cleaning.
PLEASE KEEP THESE IMPORTANT SAFEGUARDS IN MIND WHEN USING THE APPLIANCE:
CAUTION: Do not press the steam trigger until the Direct Steam Nozzle is snapped into the main
nozzle of your Handheld Steamer.
CAUTION: Do not press the steam trigger while removing the Direct Steam Nozzle. Avoid touching
the tip of the Direct Steam Nozzle, as this will be very hot after steaming.
NOTE: To remove the Direct Steam Nozzle, press and hold down the Handheld Release Buttons. Then slide
out the Direct Steam Nozzle using the grip.
NOTE: The Handheld Steamer may continue to emit steam for a few seconds after the trigger is released. This
is normal, and the steaming will eventually come to a stop.
fig. 13 fig. 14
Using the Direct Steam Nozzle
For a full list of what is included with your Steam Mop, please refer to box's top panel.

12sharkclean.com
English
How to Attach/Detach:
• Use the lavender loop on the side of the bonnet to slide over the nozzle opening of the Garment Steamer. (fig. 15)
• Snap the bristle frame over the bonnet with the bristles placed at the top of the Garment Steamer bonnet.
• Attach the assembled Garment Steamer to the Handheld Steamer by snapping it into the main nozzle. (fig. 16)
• To remove, wait 2 to 3 minutes for the tool to cool, hold the release button and pull the tool away from the unit.
Usage:
• The Garment Steamer is ideal for removing wrinkles from clothing and for freshening and grooming upholstery.
• The bonnet and frame with bristles provides controlled steaming for fabrics and upholstery.
Cleaning Tips:
• Pressing the steam trigger in 3-to-5-second bursts, move slowly up and down over your garments or upholstery.
(fig. 17)
• Always determine color fastness of any fabric, especially with reds or blues:
– Take a clean, moist, warm towel and gently rub a small area on the fabric that is as out of sight and out of the
way as possible.
– If color bleeds onto the towel, you may need to have the piece professionally cleaned.
Using the Garment Steamer
fig. 15 fig. 17fig. 16
CAUTION: Make sure the Handheld Steamer is unplugged or in Standby mode while attaching or
removing the accessory. Avoid touching the accessory, as it will be very hot after steaming.
CAUTION: To avoid scalding injuries, always unplug and allow the Steam Mop to cool before removing or
changing accessories or pads.
For a full list of what is included with your Steam Mop, please refer to box's top panel.

13 1-800-798-7398
How to Attach/Detach:
• First attach the Accessory Hose to the Handheld Steamer by snapping the Accessory Hose into the main nozzle.
(fig. 18)
• Slide the Precision Clean Pocket Pad over the Precision Clean Pocket Accessory so it fits snugly. Cinch the elastic
band and slide the locking toggle to tighten. Attach the Precision Clean Pocket Accessory by connecting it to the
Direct Steam Nozzle until it clicks into place.
• Do not use the Precision Clean Accessory without the Precision Clean Pocket Pad attached.
• Press the Flat Scrubber Tool onto the Accessory Hose until it clicks into place. (fig. 19)
• To remove, wait 2 to 3 minutes for the tool to cool, hold the release button and pull the tool away from the unit.
Usage:
• The Precision Clean Pocket Accessory is ideal for small, uneven surfaces. The pointed tip is great for edges and
corners. (fig. 20)
Cleaning Tips:
• Additional attachments are available for your accessory hose. Please visit sharkclean.com for more information.
Using The Accessory Hose and The Precision Clean Accessory
fig. 19fig. 18 fig. 20
CAUTION: Make sure the Handheld Steamer is unplugged or in Standby mode while attaching or
removing the accessory. Avoid touching the accessory, as it will be very hot after steaming.
CAUTION: To avoid scalding injuries, always unplug and allow the Steam Mop to cool before removing or
changing accessories or pads.
For a full list of what is included with your Steam Mop, please refer to box's top panel.

14sharkclean.com
English
AFTER USE AND STORAGE
1Press the Steam Control Button until it starts to blink,
indicating that you are in Standby mode. Unplug the
cord from the outlet and place the Steam Mop into
the upright position. Let it cool.
2To remove the Dirt Grip
™
pad, lift the Steam Mop straight
up by the handle until the Intelli-Mop
™
Head is hanging
straight down. Press the pad release buttons on the
neck of the mop head, and both sides of the Intelli-Mop
Head will drop open, releasing the pad. Once the pad
has been released, close the Intelli-Mop Head.
3 If the Intelli-Mop Head is not attached to the mop, the
pad can still be removed. Press down on the release
button on the Intelli-Mop Head post to release the pad
(fig. 21).
4Empty the water tank before storing. To empty the
tank, hold the Steam Mop beside a sink. Open the
water tank lid, then lean the unit over the sink. Let
the water drain out, then close the lid.
5 To store the Steam Mop, wait until after it has cooled
and the steam has been released. Then remove the
Intelli-Mop Head and hang the mop by its handle on a
large hook (not included) (fig. 22).
Caring for Your Steam Mop
DIRT GRIP™PAD CARE INSTRUCTIONS
Care
Machine-wash the Dirt Grip pads separately with warm
water using liquid detergent.
NEVER USE BLEACH, POWDERED DETERGENT, OR
FABRIC SOFTENERS as they may damage or leave
a coating on the Dirt Grip pads that will reduce their
cleaning performance and absorbency . Dirt Grip pads
should be line-dried or tumble-dried on a low setting, as
this will extend the life of the microfiber fabric (fig. 23).
Loose fibers can indicate wearing of the microfiber
fabric. Do not pull the loose fibers, as this can cause the
weave to come undone. Simply trim the loose fibers with
scissors (fig. 24).
Replacement Dirt Grip pads
For best cleaning results, we recommend replacing your
Dirt Grip pads every 3 to 4 months following normal use.
As with any fabric, dirt particles, grease, friction, and
repeated washing can cause the fibers to break down, and
you may notice an increase in the effort needed to push or
pull the mop.
You can purchase replacement Dirt Grip pads and
other accessories by visiting sharkclean.com or calling
1-800-798-7398.
STEAM NOZZLE CARE
If you believe the main steam nozzle or the Steam Blaster
™
nozzle is clogged, please contact Customer Service at
1-800-798-7398 or [e-mail]
fig. 22
fig. 21
fig. 23
fig. 24

15 1-800-798-7398
Ordering Additional Accessories
ACCESSORY
Intelli-Mop™Head
Great for all-purpose cleaning. Get an extra boost for tough stains from the Steam
Blaster
™
, and cut your cleaning time in half with the hands-free two-sided pad.
Dirt Grip™Pad
Double-sided pad. Easy, hands-free installation and removal. Washable and
reusable.
Triangle Scrubber Head
Triangle shape is perfect for cleaning corners and hard-to-reach areas.
Equipped with a Steam Blaster to help loosen stains and a deployable
scrubber to tackle stuck-on spots.
Triangle Scrubber Pad
Ideal for cleaning corners and other hard-to-reach spaces. Easy to install
and remove.

16sharkclean.com
English
Troubleshooting Guide
PROBLEM POSSIBLE REASONS & SOLUTIONS
The Steam Mop isn’t
producing any steam.
The Steam Mop should be securely plugged into an electrical outlet. Check your fuse or
circuit breaker or try a different outlet.
Make sure the water tank is full, the unit is plugged in, and the light around the Steam
Control Button is solid.
If the lights below the Steam Control Button are not illuminated, try a different electrical outlet.
If the lights below the Steam Control Button are blinking, press the Steam Control
Button to select a Steam setting.
If the lights below the Steam Control Button are solid, wait 30 seconds for the unit to warm up.
If after following the above steps the Steam Mop still does not produce any steam, contact
Customer Service at 1-800-798-7398 or [email protected]
The Steam Mop is
producing intermittent
steam.
This is normal—for more consistent steam select the SCRUB setting.
Also make sure the water tank is full.
I can’t select a Steam
Setting.
Make sure the Steam Mop is plugged in and the lights below the Steam Control Button
are solid.
If your Steam Mop is producing steam but the lights below the Steam Control Button
are not lit, call customer service at 1-800-798-7398.
I am getting streaky/
cloudy floors.
The Dirt Grip™pad might be dirty. If it is, flip it over to the clean side or change it
entirely. If you washed the Dirt Grip pad with powdered detergent, then it could be
damaged and require replacement.
This could also be an indication of soap or grease residue that has accumulated on the
floor. As the Steam Mop uses only a small amount of water, it may not be enough to rinse
off the accumulation of residue that the steam is bringing to the surface. We suggest
rinsing the floor with nothing but water, letting it dry, and then steam mopping again with a
clean Dirt Grip pad. One or more rinses will generally remove the residue.
A more stubborn case may require you to rinse the floor with a mix of one part vinegar
and two parts water* (but DO NOT put vinegar or any other cleaner into the Steam
Mop's water tank.)
*Please consult your flooring manufacturer’s care and maintenance instructions before
applying any cleaning products or solutions including vinegar.

17 1-800-798-7398
Frequently Asked Questions
QUESTION ANSWER
Can I use the Steam Mop on
carpets? No, the Steam Mop is not designed for carpet cleaning.
What surfaces can I use the
Steam Mop on?
The Steam Mop is designed for use on all sealed hard floor surfaces. We
recommend that you first test an isolated area of the floor surface to be cleaned as
well as review the use and care instructions from your floor manufacturer.
WARNING: Do not use on leather, wax-polished furniture, synthetic
fabrics, velvet, or other delicate, steam-sensitive materials.
NOTE: On surfaces treated with wax and on some no-wax floors, the sheen
may be removed by the heat or steam action of the unit. Test an isolated area of
flooring first to see if sheen is affected.
Can I put something other than
water in the water tank of the
Steam Mop?
DO NOT add cleaning solutions, scented perfumes, oils, or any other chemicals
to the water used in this appliance, as this may damage the unit or make it
unsafe for use. We recommend using distilled water in your Steam Mop.

18sharkclean.com
English
ONE (1) YEAR LIMITED WARRANTY
SharkNinja Operating LLC warrants this product to be free from defects in material and workmanship for a period
of one (1) year from the date of the original purchase, when utilized for normal household use, subject to the following
conditions, exclusions, and exceptions.
If your appliance fails to operate properly while in use under normal household conditions within the warranty period,
return the complete appliance and accessories, freight prepaid. For assistance with warranty service options or
customer support, please call Customer Service at 1-800-798-7398 or visit sharkclean.com.
If the appliance is found to be defective in material or workmanship, SharkNinja Operating LLC will repair or replace
it free of charge. Proof of purchase is required and a fee of $19.95 will apply to cover the cost of return freight.*
The liability of SharkNinja Operating LLC is limited solely to the cost of the repair or replacement of the unit at our
option. This warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with
or used for commercial purposes. This limited warranty does not cover damage caused by misuse, abuse, negligent
handling, or damage due to faulty packaging or mishandling in transit. This warranty does not cover damage or defects
caused by or resulting from damages from shipping or from repairs, service, or alterations to the product or any of its
parts that have been performed by a repair person not authorized by SharkNinja Operating LLC.
This warranty is extended to the original purchaser of the unit and excludes all other legal and/or conventional
warranties. The responsibility of SharkNinja Operating LLC warranty, if any, is limited to the specific obligations
expressly assumed by it under the terms of the limited warranty. In no event is SharkNinja Operating LLC liable for
incidental or consequential damages of any nature whatsoever. Some states/provinces do not permit the exclusion or
limitation of incidental or consequential damages, so the above may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or
province to province.
*Important: Carefully pack item to avoid damage in shipping. Be sure to include proof of purchase date
and to attach tag to item before packing with your name, complete address, and phone number with a
note giving purchase information, model number, and what you believe is the problem with the item. We
recommend you insure the package (as damage in shipping is not covered by your warranty). Mark the
outside of your package “ATTENTION CUSTOMER SERVICE”.
Product Registration
Please visit registeryourshark.com or call 1-800-798-7398 to register your new Shark®product within ten (10) days
of purchase. You will be asked to provide the store name, date of purchase, and model number, along with your name and
address.
The registration will enable us to contact you in the unlikely event of a product safety notification. By registering, you
acknowledge you have read and understood the instructions and the accompanying warnings set forth in this owner’s guide.

19 1-800-798-7398
LORS DE L’UTILISATION DE LA
VADROUILLE À VAPEUR SHARKMD
LIFT-AWAYMD PRO STEAM POCKETMD,
DES MESURES DE SÉCURITÉ DE BASE
DOIVENT TOUJOURS ÊTRE RESPECTÉES,
INCLUANT LES SUIVANTES:
LIRE TOUTES LES DIRECTIVES AVANT
D’UTILISER VOTRE VADROUILLE SHARK
LIFT-AWAY PRO STEAM POCKET.
AVERTISSEMENT: RISQUE DE
BRÛLURE.
La vapeur émise par la vadrouille à
vapeur est très chaude et peut provoquer
des brûlures. Veuillez utiliser la
vadrouille à vapeur avec précaution.
AVERTISSEMENT: GARDER LA
VADROUILLE À VAPEUR HORS DE PORTÉE
DES ENFANTS.
FICHE POLARISÉE:
Cette vadrouille à vapeur est munie d’une fiche
polarisée (une lame est plus large que l’autre).
À des fins de sécurité, cette fiche s’insère
dans une prise polarisée dans un seul sens.
Si la fiche ne s’insère pas entièrement dans
la prise, inversez la fiche. Si elle ne s’insère
toujours pas, communiquez avec un électricien
accrédité. Ne pas tenter de contourner ce
dispositif de sécurité. Il n'est pas recommandé
d'utiliser une rallonge électrique avec ce
produit.
CONSIGNES DE SÉCURITÉ IMPORTANTES
Pour usage domestique seulement
AVERTISSEMENT:
AFIN DE RÉDUIRE LES RISQUES D’INCENDIE,
D’ÉLECTROCUTION OU DE BLESSURE:
1. Lors de son utilisation, ne jamais faire pencher
la vadrouille à vapeur sur le côté et ne pas
diriger la vapeur vers les personnes, les
animaux ou les plantes.
2. Employer le système uniquement pour son
utilisation prévue.
3. NE PAS UTILISER comme source de
chauffage domestique.
4. NE PAS UTILISER cet appareil à l’extérieur.
5. NE PAS LAISSER la vadrouille à vapeur sans
surveillance lorsqu’elle est branchée. Toujours
débrancher le cordon d’alimentation de la prise
électrique lorsque l’appareil n’est pas utilisé et
avant d’effectuer son entretien.
6. NE PAS LAISSER les enfants se servir de
la vadrouille à vapeur. Porter une attention
particulière lorsque le produit est utilisé à
proximité d’enfants, d’animaux ou de plantes.
7. Utiliser l’appareil uniquement comme le décrit le
guide du propriétaire.
8. Utiliser seulement les accessoires
recommandés par le fabricant.
9. NE PAS UTILISER l’appareil si le cordon
d’alimentation ou la fiche sont endommagés.
Si la vadrouille à vapeur ne fonctionne pas
comme prévu, est tombée, a été endommagée,
a été laissée à l’extérieur ou est entrée en
contact avec de l’eau, retournez-la à SharkNinja
Operating LLC aux fins d’examen et de
réparation. Des réparations ou un réassemblage
incorrects peuvent présenter des risques de
décharges électriques ou de blessures quand la
vadrouille à vapeur est utilisée.
10. Pour se protéger contre les décharges
électriques, NE PAS IMMERGER la vadrouille à
vapeur dans l’eau ou tout autre liquide.