Shark S3251NZGN User manual

S3251NZGN
OWNER’S GUIDE
SHARK®STEAM LIGHT
STEAM MOP

WHEN USING YOUR SHARK®
STEAM MOP, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS
BE FOLLOWED, INCLUDING THE
FOLLOWING:
WARNING: TO REDUCE
THE RISK OF FIRE, ELECTRIC
SHOCK OR INJURY READ ALL
INSTRUCTIONS BEFORE USING
YOUR SHARK®STEAM LITE.
DANGER OF SCALDING.
Please use caution when using the
steam mop. The steam emitted from the
openings is very hot.
IMPORTANT:
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities
or lack of experience and knowledge,
unless they have been given supervision
or instruction concerning the use of the
appliance by a person responsible for their
safety.
Children should be supervised to ensure
that they do not play with the appliance.
1. Use the system only for its intended
use.
2. DO NOT use outdoors.
3. DO NOT leave the appliance
unattended when plugged in. Always
unplug the power cord from the
electrical outlet when not in use and
before servicing.
4. DO NOT allow the appliance to
be used as a toy. Close attention
is necessary when used by or near
children, pets or plants.
5. Use only as described in this manual.
6. Use only manufacturer’s recommended
accessories.
7. DO NOT operate the appliance with
a damaged plug or cord, or if the unit
has been dropped or damaged. To
avoid the risk of electric shock, do not
disassemble or attempt to repair the
appliance on your own. If the supply
cord is damaged, it must be replaced
by a qualified electrician in order to
avoid a hazard. Incorrect re-assembly
or repair can cause a risk of electrical
shock or injury to persons when the
appliance is used.
8. To protect against a risk of electric
shock, DO NOT immerse the steam
mop into water or any other liquids.
9. DO NOT handle plug or steam mop
with wet hands or operate appliance
without shoes.
10. DO NOT pull or carry by the power
cord, use the power cord as a handle,
close a door on the power cord, or pull
the power cord around sharp edges or
corners. Keep power cord away from
heated surfaces.
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
For Household Use Only

11. DO NOT unplug by pulling on power
cord. To unplug, grasp the plug not
the power cord. Do not use extension
cords or outlets with inadequate
current carrying capacity.
12. DO NOT put any objects into
openings. Do not use with any
opening blocked.
13. DO NOT put hands or feet under the
steam mop as the unit gets very hot.
14. Use ONLY on flat, stable horizontal
surfaces. Do not use on walls,
counters, windows, chairs or tables.
15. DO NOT use on leather, wax
polished furniture or floors, synthetic
fabrics, velvet or other delicate, steam
sensitive materials.
16. Liquid or steam must not be directed
towards equipment containing
electrical components, such as the
interior of ovens.
17. DO NOT add cleaning solutions,
scented perfumes, oils or any other
chemicals to the water used in this
appliance as this may damage the unit
or make it unsafe for use. If you live
in a hard water area, we recommend
using distilled water in your steam
mop.
18. When in use, NEVER turn the
appliance over or on its side. NEVER
DIRECT STEAM TOWARDS
PEOPLE, ANIMALS OR PLANTS.
19. NEVER LEAVE THE CLEANING
UNIT IN ONE SPOT ON ANY
SURFACE FOR ANY PERIOD OF
TIME WHEN MICROFIBRE PAD
IS ATTACHED.
20. Carefully remove the microfibre pad
immediately after you have unplugged
and allowed the product to cool.
21. When cleaning the steam mop, unplug
the power cord from the electrical
outlet and clean with a dry or damp
cloth. Do not pour water or use
alcohol, benzene or paint thinner on
the unit.
22 To reduce the risk of fire, DO NOT
use a flammable or combustible liquid
to clean a floor.
23. Extreme caution should be exercised
when using this appliance to clean
stairs.
24. Never use the steam mop without
microfibre pad attached.
25. Keep your work area well lit.
26. Store steam mop indoors in a cool, dry
place.
27. To avoid circuit overload, do not
operate another appliance on the
same socket (circuit) as the steam
cleaner.
28. If an extension cord is absolutely
necessary, an extension cord rated a
minimum of 15 ampere, 14 gage cord
should be used. Cords rated for less
amperage may overheat. Care should
be taken to arrange the cord so that it
cannot be pulled or tripped over.
29. DO NOT leave unattended when
the system is connected to a power
supply or electrical outlet. Turn off all
controls before unplugging the unit.
30. DO NOT store the unit with a
damp or wet microfibre cleaning pad
attached.
WARNING: Your steam mop is
designed to clean hard floor surfaces
that will withstand high heat. Do not
use on unsealed wood or unglazed
ceramic floors. On surfaces that have
been treated with wax or some no
wax floors, the sheen may be removed
by the heat and steam action. It is
always recommended to test an
isolated area of the surface to be
cleaned before proceeding. We also
recommend that you check the use
and care instructions from the floor
manufacturer.

ASSEMBLE
1Fit the extension tubes together, as shown
in the illustration. (fig. 1)
2Place the microfibre cleaning pad
underneath the mop head, with quick
fastener strips facing up. Simply press the
mop to the pad to attach it. (fig. 2)
FILL
3Remove the cap to fill the water tank. Use
the filling flask and funnel to fill the tank
with water to the “MAX” fill line. Replace
the water tank cap. (fig. 3)
Quick Start
fig. 1 fig. 2
fig. 3
CUSTOMER CARE - NZ: 0800 002 999 CUSTOMER CARE - AU: 1800 890 840

STEAM CLEANING
4For your comfort, you can adjust the height
of the mop. Just lift the latch on the tube
90 degrees to the open position. Holding
the handle, extend the tube to the desired
height and then close the latch to the
locked position.
5Plug in the mop. Wait 30 seconds for the
unit to heat up and the steam to be ready.
Push the handle toward the mop head in a
pumping motion. Customise steam output
by slow or fast mopping with a forward and
backward motion. (fig. 4)
Quick Start
fig. 4
QUICK TIP:
For easier
pushing and
pulling, extend
the handle
length.
NOTE: Do not leave your Steam Mop
unattended during use.
IMPORTANT: Never leave the steam
mop in one spot for any period of time
with a damp or wet microfibre pocket
attached as this will damage your
floors.
CUSTOMER CARE - AU: 1800 890 840

CUSTOMER CARE - NZ: 0800 002 999
THIS BOOK COVERS MODEL NUMBER:
S3251NZGN 11
TECHNICAL SPECIFICATIONS
Voltage: 220-240V~, 50/60Hz.
Power: 1550W
Water
Capacity: 250 ml (8 oz.) IPX4Z854

Contents
GETTING STARTED ..............................................................................2
USING YOUR STEAM MOP ..................................................................6
CARE OF YOUR STEAM MOP...............................................................8
TROUBLESHOOTING..........................................................................10
Thank you for
purchasing the
Shark®Steam
Lite Steam Mop.
CUSTOMER CARE - AU: 1800 890 840

2
Getting Started
a Upper Extension Tube
b Lower Extension Tube (Telescopic)
c Steam Mop Base
d Microfibre Cleaning Pad
e Funnel
f Filling Flask
ASSEMBLY
1Remove all the parts from the package. Verify all
the listed parts are included.
2Slide the upper extension tube (the tube with the
handle) into the lower extension tube (the short
tube). Push the two extension tubes together
until they click into place. (fig. 1)
When assembling your steam mop there may be
a little water in or around the water tank. This is
because we test all our steam mops 100% before
you buy them, so you get a quality Shark®Steam
Lite Steam Mop.
fig. 1
a
bc
d
ef
CUSTOMER CARE - NZ: 0800 002 999

3
IMPORTANT: Never use the Shark®Steam
Lite Steam Mop without attaching a microfibre
cleaning pad to avoid damage to your floor and
mop.
IMPORTANT: Do not use on unsealed wood
or unglazed ceramic floors. On surfaces that
have been treated with wax or some no wax
floors, the sheen may be removed by the heat
and steam action. It is always recommended to
test an isolated area of the surface to be cleaned
before proceeding. We recommend that you
check the use and care instructions from the
floor manufacturer.
3Insert the assembled handle piece into the steam
mop base. Push the tube base together until you
hear a click. (fig. 2)
4For your comfort, you can adjust the height
of the mop. Just lift the latch on the tube 90
degrees to the open position. Holding the
handle, extend the tube to the desired height
and then close the latch to the locked position.
(fig. 3)
QUICK TIP: For easier pushing and pulling,
extend the handle length.
fig. 2
fig. 3
CUSTOMER CARE - AU: 1800 890 840

4
IMPORTANT: Only add water to the tank.
Chemicals or cleaning solutions may be unsafe
or cause damage.
IMPORTANT: Please wait 3-5 minutes for your
Shark®Steam Lite Steam Mop to cool off
before removing the microfibre pad.
ATTACHING THE MICROFIBRE PAD
1Place the microfibre cleaning pad on the floor
with the quick fastener strips facing up. Place
the Shark®Steam Lite Steam Mop on the top
of the pad to attach. (fig. 4)
Getting Started
Your microfibre cleaning pads should be
replaced every 3 months to maximise
cleaning performance.
fig. 4
CUSTOMER CARE - NZ: 0800 002 999

5
FILLING THE WATER TANK
IMPORTANT: Unplug the Shark®Steam Lite
Steam Mop before filling the water tank with
water.
1Remove the water tank cap by turning it
counter-clockwise to the unlocked position.
(fig. 5)
2A filling flask and funnel are included with your
Shark®Steam Lite Steam Mop to make filling
the water tank easy. Fill the flask with water and
use the funnel to pour it into the tank. Keep the
water level under the “MAX” fill line.
3Replace the water tank cap and turn it clockwise
to the locked position.
fig. 5
CUSTOMER CARE - AU: 1800 890 840

6
IMPORTANT: Your steam mop needs water to
make steam! Never use your steam mop without
water in the tank.
Sweep or vacuum your floors prior to cleaning
with your Shark®Steam Lite Steam Mop.
Using Your Shark®Steam Lite Steam Mop
1Pull and twist the quick release cord holder to
unwrap the power cord completely. (fig. 6) Plug
into an electrical outlet. The “On” light will turn
blue. If the light does not turn on, reference the
troubleshooting section on page 10. (fig. 7)
When you use your steam mop for the first time or
if you have not used the unit in awhile, it may take
a minute or two for the water to travel through the
pump and into the heater to create steam. Get it
started by pumping the handle a few times. If you
have waited a few minutes and you still do not see
any steam, reference the troubleshooting section on
page 10.
fig. 6
fig. 7
CUSTOMER CARE - NZ: 0800 002 999

7
2Wait 30 seconds for the boiler to heat the water.
Pump the handle a few times to prime the pump,
activate steam and moisten the microfibre pad.
(fig. 8)
3Mop with a forward and backward motion to
customise steam output automatically. (fig. 9)
IMPORTANT: Never leave the Shark®Steam
Lite Steam Mop with a damp/wet microfibre pad
on any floor surface for any amount of time as
this may damage the floor.
If your Shark®Steam Light Steam
Mop stops steaming, it could be out
of water. Unplug the power cord from
the electrical outlet and refill the water
tank at anytime.
fig. 8
fig. 9
CUSTOMER CARE - AU: 1800 890 840

8
4To store the cooled Shark®Steam Lite Steam
Mop, hang on a large hook. (fig. 11)
NOTE: If you want to store the Shark®Steam
Lite Steam Mop standing upright, make sure it
is leaning against a wall for added support and
safety. Always store your Shark®Steam Lite
Steam Mop with the microfibre cleaning pad
removed. Store away from children and high
traffic areas.
Care of Your Shark®Steam Lite Steam Mop
AFTER USE AND STORAGE
1When you have finished using the Shark®
Steam Lite Steam Mop, unplug the cord from
the outlet and place the mop into the upright
position and let the unit cool for 3-5 minutes.
Release steam by pumping the handle several
times.
2 Carefully separate microfibre cleaning pad from
steam mop, avoiding contact with the hot pad or
dirt. (fig. 10)
3Empty the water tank before storage. Remove
the water tank cap and empty the tank over a
sink. Replace the water cap.
fig.10 fig.11
CUSTOMER CARE - NZ: 0800 002 999

9
2If there are loose threads on the pad carefully
cut the threads with scissors. Do not pull on
them or cut at the base. (fig. 13)
IMPORTANT: The microfibre cleaning pad may
be very hot from the steam. Use caution when
removing. Let the unit cool for 3-5 minutes first
before removing.
CARE OF YOUR MICROFIBRE CLEANING
PAD
1Wash pads in warm water. Wash separately from
other laundry. Only use liquid detergent (no
powder detergent). Do not use fabric softeners.
Line dry or dry on a low dryer setting. (fig. 12)
fig. 12
fig. 13
40°
CUSTOMER CARE - AU: 1800 890 840

10
Trouble Shooting
PROBLEM POSSIBLE REASONS & SOLUTIONS
The Shark®Steam Lite
Steam Mop will not
turn-on.
Your steam-mop should be securely plugged into an electrical outlet only.
Check your fuse or breaker.
Shark®Steam Lite
Steam Mop will not
make steam.
Is there water in the water tank? If not, add water to your steam mop
following instructions on page 5.
Shark®Steam Lite
Steam Mop leaves water
on the floor.
Is your microfibre cleaning pad too wet? Unplug your steam mop and change
the microfibre cleaning pad.
Shark®Steam Lite
Steam Mop left white
spot on
the floor.
Do not leave your steam-mop on the floor with a damp or wet cleaning pad.
Do you have hard water? If you do, you might want to switch to distilled
water.
Make sure the water tank cap is securely on the water tank.
Floors are cloudy,
streaky or spotty after
steaming.
The pad might be dirty, change the pad.
If you washed the pocket with powder detergent, then the pad may have
residual detergent left on it. Wash it again with liquid detergent.
If you are cleaning in a kitchen area where there might be a build-up of
grease, use a de-greasing agent such as an all-purpose cleaner or dish soap
and paper towels to clean the area first.
You might have left the mop in the same spot for too long.
Do you have hard water? If you do, you might want to switch to distilled
water.
This might be leftover from past cleaners used on the floor surface. Use the
steam mop a few more times and see if the leftover cloudiness is removed.
Shark®Steam Lite
Steam Mop is hard to
push.
Make sure the steam pad is attached correctly.
Check to see if the cleaning pad is excessively dirty. Replace if the pad is too
dirty or wet.
CUSTOMER CARE - NZ: 0800 002 999

11
Notes
CUSTOMER CARE - AU: 1800 890 840

12
Notes
CUSTOMER CARE - NZ: 0800 002 999

13
CUSTOMER CARE - AU: 1800 890 840
ONE (1) YEAR
LIMITED REPLACEMENT WARRANTY STATEMENT
If your product becomes defective due to faulty material or workmanship within a period of 1 year from the date
of purchase, we warrant to do the following:
• For New Zealand Consumers: We will replace the product with a new product, free of charge, or repair
the product at our cost, at our discretion.
• For Australian Consumers: Our goods come with guarantees that cannot be excluded under the
Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for
compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the
goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount
to a major failure.
Your warranty is subject to the following conditions:
• DO NOT operate the appliance with a damaged plug or cord, or if the unit has been dropped, damaged
or dropped in water. To avoid the risk of electric shock, do not disassemble or attempt to repair the
appliance on your own. If the supply cord is damaged, it must be replaced by a qualified
electrician in order to avoid a hazard. Incorrect re-assembly or repair can cause a risk of
electrical shock or injury to persons when the appliance is used.
• The product has not been misused, abused, neglected, altered, modified or repaired by anyone.
• The product has been subjected to fair wear and tear.
• The product has not been used for trade, professional or hire purposes.
• The product has not sustained damage through foreign objects, substances or accident.
Your warranty does not cover:
• Components that are subject to natural wear and tear caused by normal use in accordance with
operating instructions.
• Unauthorised/improper maintenance/handling or overload is excluded from this warranty.
• For guarantee claims you will need to submit a proof of purchase in the form of a valid receipt that
displays date and place of purchase.
This warranty does not replace but is in addition to your statutory rights.
This warranty does not apply to accessories supplied with the product.
This warranty applies only to the original purchaser and may not be transferred.
Replacement products will be covered by the limited warranty for the balance of the warranty period from the
date of the original purchase.
Please note:
Only defective product or parts returned to place of purchase will be replaced under this warranty.
New Zealand Contact: Australia Contact
Brand Developers Limited Brand Developers Aust Pty Ltd
Unit H, 686 Rosebank Road, 461 Plummer Street,
Avondale 1026, Auckland, New Zealand PORT MELBOURNE, VIC 3207
FAX: [phone] FAX: [phone]
NZ Customer Care 0800 002 999 AUST Customer Care: 1800 890 840

IPX4
Z854
Printed in China
Illustrations may differ from actual product.
S3251NZGN.E.131223.1