Sharp FU-S25E User manual

ENGLISH
FU-S25E
HECCRBQ
R
ESPAÑOL FRANÇAIS ENGLISH
ITALIANO
NEDERLANDS
DEUTSCH
*Plasmacluster is a trademark of
Sharp Corporation.
Free standing type
Tisch- / Wandgerät
Type de table / installation murale
De sobremesa / instalación en la pared
Tipo da scrivania / parete
Tafelmodel / wandmodel
AIR PURIFIER
OPERATION MANUAL
LUFTREINIGER
BEDIENUNGSANLEITUNG
PURIFICATEUR D'AIR
MANUEL D'UTILISATION
PURIFICADOR DE AIRE
MANUAL DE USO
PURIFICATORE
DELL’ARIA
MANUALE OPERATIVO
LUCHTREINIGER
GEBRUIKSAANWIJZING

Please read before operating your new Air Purifier
The air purifier draws in room air from its air intake, lets the air pass through a
Active Carbon Filter (deodorization filter) and a HEPA Filter (dust collection
filter) inside of the unit, then discharges the air from its air outlet. The air
purifier unit repeats this process by moving its internal fan.
As air passes through, a new HEPA Filter can remove 99.97% of dust parti-
cles, of as small as 0.3 microns. The Active Carbon Filter gradually absorbs
odour elements as they repeatedly pass through the filter. (Odour elements
are absorbed by HEPA Filter as well.)
Some odour ingredients absorbed by the filters may become separated and
may be discharged through the air outlet and result in additional odour. De-
pending on the usage environment, especially when the product is used in a
condition significantly more severe than household use, this odour may be-
come strong in a shorter period than expected.
If the odour persists, then the filters are fully expended and it is necessary to
purchase the optional replacement filter.
ENGLISH
NOTE
• The air purifier is designed to remove air-suspended dust and odour, but not harmful gases (for
example, carbon monoxide contained in cigarette smoke). If the odour sources still exist, it cannot
completely remove the odour. (for example, odours from construction materials and pet odours).
• It is suggested to open the window a bit when you are smoking in order to facilitate ventilation.

ENGLISH
FEATURES
ION SHOWER
E-1
Thank you for purchasing the SHARP Air Puri-
fier.Pleasereadthismanualcarefullyforthecor-
rect usage information. Before using this prod-
uct,besuretoreadthesection:“Important Safety
Instructions.”
After reading this manual, retain it in a conven-
ient location for future reference.
IMPORTANT SAFETY INSTRUCTIONS .... E-2
• WARNING....................................................E-2
• CAUTIONS CONCERNING OPERATION ...E-3
• INSTALLATION GUIDELINES .....................E-3
• FILTER GUIDELINES ..................................E-3
PART NAMES..........................................E-4
• MAIN UNIT DISPLAY...................................E-4
• ILLUSTRATIVE DIAGRAM .........................E-4
• BACK ...........................................................E-5
• INCLUDED...................................................E-5
PREPARATION........................................ E-6
• FILTER INSTALLATION ...............................E-6
OPERATION ............................................E-8
• MAIN UNIT OPERATION.............................E-8
CARE AND MAINTENANCE................. E-10
• MAIN UNIT................................................ E-10
• FILTER ...................................................... E-10
• SENSOR................................................... E-10
• WASHABLE ACTIVE CARBON FILTER CARE .... E-11
• FILTER REPLACEMENT
GUIDELINES ............................................ E-12
TROUBLE SHOOTING.......................... E-13
SPECIFICATIONS ................................. E-14
INFORMATION ON PROPER DISPOSAL ... E-15
CONTENTS
New ION SHOWER Operation Mode
releases the concentrated Plasmacluster
Ions, and effectively removes the pollen
and mold, and also controls the activity of
airborne virus, mold, and allergen.
Plasmacluster Ion Control
Your new air purifier will control the ratio
of negative ions and positive ions de-
pending on the condition of the room.
• Clean Mode
Approximately the same numbers of
positive and negative ions are dis-
charged.
• AUTO Plasmacluster Ion
Mode
Theunitwill switchbetween Clean Mode
andIonControl Mode* automaticallyde-
pending on the amount of impurities in
the air detected by the odour and dust
sensors.
*Ion Control Mode
Negative ions will be released in an
increased rate and controls the ion
balance.
• Filters
1) Washable Active Carbon Filter
Absorbs odour elements.
Washable to maintain optimum
deodorization performance.
2) HEPA (High Efficiency
Particulate Air) Filter
High-efficiency particle collection in-
cluding pollen and dust.

E-2
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, basic safety precautions should be followed, including the
following:
WARNING - To reduce the risk of electrical shock, fire or injury to persons:
• Read all instructions before using the air purifier.
• Use only a 220-240 volt outlet.
• Do not use the air purifier if the power cord or plug is damaged or the connection to the wall
outlet is loosened.
•Periodically remove dust from the power plug.
• Do not insert fingers or foreign objects into the intake or air outlet.
• When removing the power plug, always hold the plug and never pull the cord.
Electrical shock and/or fire from short circuit may occur as a result.
• Do not remove the plug when your hands are wet.
• Do not use this air purifier near gas appliances or fireplaces.
• Remove the power plug from the wall outlet before cleaning the unit and when not using the
unit.
Electrical shock from bad insulation and/or fire from short circuit may occur as a result.
• If the power cord is damaged, it must be replaced by the manufacturer, its service agent,
Sharp authorized Service Centre or similarly qualified person in order to avoid a hazard.
•Do not operate when using aerosol insecticides or in rooms where there is oily residue, incense,
sparks from lit cigarettes, chemical fumes in the air or in very high humidity condition, such as a
bathroom.
•Be cautions when cleaning the air purifier. Strong corrosive cleansers may damage the exterior.
•Only Sharp Authorized Service Centre should service this air purifier. Contact the nearest Service
Centre for any problems, adjustments, or repairs.
NOTE - Radio or TV Interference
Ifthis airpurifier should cause interferenceto radioor television reception,try tocorrect the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the air purifier and radio/TV receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is con-
nected.
• Consult the dealer or an experienced radio/TV technician for help.

ENGLISH
E-3
CAUTIONS CONCERNING OPERATION
• Do not block the intake and air outlet.
• Do not use the unit near or on hot objects, such as stoves or heaters or where it may come into
contact with steam.
• Do not lay the unit down when using.
• Always hold the handle on the back of the unit when moving it.
Holding the front panel when carrying may cause it to detach, thus dropping the unit and resulting in
bodily injury.
• Do not operate the unit without the filter.
• Do not wash and reuse HEPA filter .
It not only does not improve filter performance, it may cause electric shock or malfunction.
• Clean the exterior with a soft cloth only.
The unit surface may be damaged or cracked.
In addition, the sensors may malfunction as a result.
IMPORTANT SAFETY INSTRUCTIONS
INSTALLATION GUIDELINES
• During the operation of the product, please place the unit at least 2m away from equipments
which involve electric wave such as televisions, radios or wave clocks, in case electrical
interference occurs to such equipment.
• Avoid a location where the sensor is exposed to direct wind.
The unit may not operate properly.
• Avoid locations where curtains, etc., come into contact with the intake or air outlet.
Curtains, etc., may become dirty or a malfunction may occur.
• Avoidlocations where the unit is exposed tocondensation, due to drastic temperature changes.
(Use under appropriate conditions between 0 and 35˚C in the room.)
• Place on a stable surface with sufficient air circulation.
When placing the unit on a heavily carpeted area, it may cause the unit to vibrate slightly.
• Do not install when there is generation of lampblack, such as in a kitchen, etc.
The unit surface may crack or the sensor may malfunction as a result.
• Leave about 60cm of space from the wall.
The wall behind the air outlet may become dirty as time passes. When using the unit for extended
period of time in the same location, use a vinyl sheet, etc., to prevent the wall from becoming dirty. In
addition, periodically clean the wall.
FILTER GUIDELINES
• Follow the instructions in this manual for correct care and maintenance of the filters.

E-4
PART NAMES
MAINUNIT DISPLAY
ILLUSTRATIVE DIAGRAM
Main Unit
Odour Sensor
HEPA Filter
(blue/white)
(black)
Filter Support
Front Panel
Washable Active
Carbon Filter
Fan Speed Indicator Lights
Pollen Mode Indicator Light
ION SHOWER Indicator Light
AUTO Operation Indicator Light
Plasmacluster Ion Mode
Indicator Lights
POWER ON/OFF Button
Plasmacluster Ion Mode Selection Button
Mode Selection Button
C
P
Odour Senser
(
P

ENGLISH
E-5
INCLUDED
• Operation manual
BACK
ENGLISH
Blue light
• When the Plasmacluster ion operation is in Clean Mode, or in AUTO Plasmacluster Ion Mode and the air in the
room is impure, the light will be activated and the unit will operate in Clean Mode.
• When the Plasmacluster ion operation is in ION SHOWER Mode, the light will repeat its colour cycles between
light and shade.
Green light
When the Plasmacluster ion operation is in the Ion Control Mode, or in AUTO Plasmacluster Ion Mode and the air
in the room is clean, this light will be activated and the unit will operate in Ion Control Mode.
The colour changes according to the air condition.
ABOUT THE CLEAN-SIGN
• The condition of the CLEAN-SIGN depends on the room air condition detected by the Odour Sensor when the
plug is inserted into the wall outlet.
• It is possible to have a green CLEAN-SIGN with impurities in the air at the time that the air purifier was just
introduced to the room environment.After a while, however, the base impurity rate will be adjusted to detect room
air condition correctly.
DETERMINING THE BASE IMPURITY RATE
For the first 30 seconds after the power plug is inserted into the wall outlet, the unit will check the conditions of the
air. If operation is set to ON during this time, the CLEAN-SIGN LIGHT will alternately flash in green, orange and red.
Green
Clean Slightly Impure Very Impure
Orange Red
Air Outlet
Data Label
Power Cord
Power Plug
Handle
M
ode
CLEAN - SIGN Light
Plasmacluster Indicator Lights
(Please refer page E-9)
(Sharp of plug depends on country.)

PREPARATION
E-6
Be sure to remove the power plug from the wall outlet.
To maintain the quality of the filters, they are installed in the main unit and packed in
plastic bags. Be sure to remove the filters from the plastic bags before using the unit.
1
Remove the filters
Remove the Front Panel.
Pull the bottom of the Front Panel.
Remove the Active Carbon
Filter and HEPA Filter.
FILTER INSTALLATION
Remove the Filter Support.
Pinch the two tabs and lift to remove.
Front Panel
Up side Tabs Tabs
Active Carbon Filter
HEPA Filter
Main Unit
Active Carbon Filter
Remove the Active Carbon
Filter and HEPA Filter from
the plastic bags.
HEPA Filter
1
4
3
2
1

ENGLISH
2
Install the filters
Place the HEPA Filter
within the main unit with
the tabs facing up.
Donot install the filter backwardsor
the unit will not operate properly.
Place the Active Carbon
Filter on top of the HEPA
Filter.
Make sure that the tab of the
HEPA Filter remains visible.
Fill in the usage start date
on the Date Label.
Use the date as a guide for the
Filter Replacement schedule.
Insert the bottom side tabs of the Filter Support
into the associated holes of the main unit.
Next push the upside tabs into the main unit.
HEPA Filter
Active Carbon Filter
Up side Tabs
Holes
Bottom side tabs
Date Label
Tabs
Filter Support
Fix the Front Panel to the
main unit.
4
2
E-7
3
5
2
1
Tab
Tabs

OPERATION
MAIN UNIT OPERATION
E-8
Power ON/OFF Button
• Used to start operation (short beep) and stop operation (long
beep)
• Plasmacluster Indicator Light and Fan Speed Indicator Light
turn on/off.
•Unless unplug the power cord, the operation starts in the
previous mode the unit was operated in.
MODE Selection Button
• The operation mode can be switched.
AUTO operation
Thefanspeedisautomaticallyswitched(HIGH*,MEDIUM,
SILENT) depending on the amount of impurities in the air.
The sensors detect the impurities for efficient air purifica-
tion.
POLLEN mode operation
The unit will operate at HIGH* fan speed for 10 minutes,
then will alternate between MEDIUM and HIGH* for
20 minutes.
10 minutes: HIGH fan speed
20 minutes: MEDIUM fan speed
20 minutes: HIGH fan speed
SILENT
operation
The unit will operate
quietly using minimal air
intake.
MEDIUM operation
The unit will operate at a
fan speed of MEDIUM.
MAX operation
The unit will operate at a
fan speed of MAX.
*HIGH fan speed is an in-
termediate speed be-
tweenMEDIUM andMAX.
ION SHOWER operation
TheconcentratedPlasmacluster Ions(IONSHOWER) will
be generated in the room like a shower for 15 minutes,
repeating the airflow cycles between strong and gentle.
(The Plasmacluster Indicator Light repeats its colour
cycles between light and shade.), and effectively controls
the airborne dust, pollen, mold, and allergen.
•Whenfinishedtheoperation, theunitwillback to theAuto
operation.
Plasmacluster ION Mode Indicator Lights
M
P
P
C
Plasmacluster Indicator Lights

ENGLISH
AUTO
The unit will switch between Clean Mode and the Ion Con-
trol Mode* automatically depending on the amount of impu-
ritiesin theair as detected by the odoursensor.Clean Mode
operate for 10 minutes when the Auto function is selected.
E-9
Plasmacluster Ion Mode Selection Button
The Plasmacluster Ion Mode can be switched.
LIGHTS ON/OFF Button
SwitchesthePlasmaclusterIndicatorLightandCLEAN-SIGN Light
either ON or OFF.
(Please press the Plasmacluster Ion Mode Selection Button for 3
seconds.)
CLEAN
The unit will constantly operate in the Clean Mode, in which
the same numbers of positive and negative ions are dis-
charged. The Plasmacluster Indicator Light is blue.
Mode Selection Button
Plasmacluster Ion Mode Selection Button
POWER ON/OFF Button
CLEAN - SIGN Light
* Ion Control Mode
Negative ions will be
released in an increased
rate and controls the ion
balance.
ION OFF
Thegenerationofionswillstop and thePlasmaclusterIndicator
Light will go out.

E-10
CARE AND MAINTENANCE
To prevent dirt or stains on the main unit, clean as often as necessary. If stains are allowed to
remain, they may become hard to clean.
Wipe with a dry, soft cloth
For stubborn stains or dirt, use a soft cloth dampened with warm water.
Do not use volatile fluids
Benzene, paint thinner, polishing powder, etc., may damage the surface.
Do not use detergents
Detergent ingredients may damage the unit.
Keep the unit away from water
MAIN UNIT
Care Cycle 1 month
To maintain optimum performance of this air purifier, please clean the unit including the sensor
and filters periodically.
When cleaning the unit, be sure to unplug the power cord, and never handle the plug with wet
hands. Electrical shock and/or bodily injury may occur as a result.
ODOR SENSOR
The sensitivity of the sensor will become unstable
ifthe odoursensor is dirtyor blocked.Remove dust
from the surface of the sensor opening using a
vacuum cleaner.
Care Cycle 2 months
Hole of sensor

ENGLISH
3
Rinse thoroughly with
clean water
Ifrinsingin a con-
tainer, be sure to
rinse 3 to 4 times
so that the odour
is rinsed thor-
oughly from the
filter.
• The wet filter is heavy. Fix it securely for drying to
make sure it does not fall down.
• The filter takes longer time to dry in winter, on rainy
days. Wash it on a day when the weather is good and
dry it in the sun.
Move it indoors at night to prevent freezing.
• Drythefilteroutdoors in awellventilatedarea. If dried
indoors, the water dripping off the filter may soil your
floor.
• Let the filter dry thoroughly.
If used while the filter is still moist, then the air that is
exhaustedfromthemain unit willhaveanodor. It may
take 1 or 2 days to dry.
WASHABLE ACTIVE CARBON FILTER CARE
Care Cycle
We recommend to the active carbon filter every six months.
Clean the filter as offen as necessary when odour persists.
1
Fill a large container with
lukewarm water, add a mild
kitchen detergent and stir.
Diluteasindicated
on the detergent
container.
4
Remove excess water
The filter will be saturated with water
afterrinsing.Todecreasedryingtime,
wrap the filter in an old thick towel so
that excess water can be removed.
HAND WASH ONLY!
DO NOT TUMBLE DRY!
2
Allow the filter to soak ap-
proximately 10 minutes .
6
Reinstall the Filters
Reinstall the filters as shown on Page E-6,7
Some carbon
may adhere to
the towel, if you
towel -dry the
filter, but it is
harmless.
HEPA Filter
Active Carbon
Filter
Filter Support
Main Unit
CAUTION
CAUTION
CAUTION
E-11
5
Dry the filter outdoors if possible in
a well ventilated area.
WASHABLE ACTIVE CARBON FILTER CARE

E-12
CARE AND MAINTENANCE
FILTER REPLACEMENT GUIDELINES
Depending on the usage environment, air outlet odour may become
strong after several months.
If dust or odour cannot be removed easily, replace the filters.
(Refer to “Please read before operating your newAir Purifier”)
Guide for filter replacement timing
•The following filter life and replacement period is based on the condition of smoking 10
cigarettes per day and the dust collection/deodorization power is reduced by half compared
with that of new filters.
We recommend to replace the filters more frequently if the product is used in a condition
significantly severer than normal household use.
•HEPA Filter About 2 years after opening
•Active Carbon Filter About 2 years after opening
REPLACING THE FILTERS
1
See page E-6,7 for directions
on how to install the filters
when replacing.
2
Fill in the usage start date of
the filters on the Date Label.
Replacement Filters
Model: FZ-425SEF
• HEPA Filter : 1 unit
• Active Carbon Filter: 1 unit
Please consult your dealer for purchase
of replacement filters.
Disposal of Filters
Please dispose of replaced filters according to the local disposal laws and regulations.
HEPA Filter materials:
•Filter: Polypropylene
•Frame: Polyester
Active Carbon Filter Materials:
•Deodorizer: Activated charcoal
•Nonwoven fabric : Polyester
Date Label

ENGLISH
E-13
Before calling for repair, please review the list below, since the problem may not be a unit malfunction.
SYMPTOM REMEDY (not a malfunction)
Odours and smoke are not
removed. • Clean or replace the filters if they appear to be heavily soiled.
(Refer to E-11E-12)
The CLEAN-SIGN Light lights
green even when the air is
impure.
• The air could be impure at the time the unit was plugged in.
(Refer to E-5) Pull out the plug from the electrical outlet, and
insert the plug one minute later.
The CLEAN-SIGN Light lights
orange or red even when the air
is clean.
• Thesensitivityofthesensorbecome unstable when the open-
ing of the odour sensor is dirty or is clogged.
Clean the dust around the sensor opening using a vacuum
cleaner. (Refer to E-10)
The Plasmacluster Indicator
Light remains green (or blue)
and does not change. • When in Ion Control Mode (or Clean Mode), the Plasmaclus-
ter Indicator Light colour will not change.
• Clicking sound is emitted when the unit is in the Ion Control
Mode,andtickingsoundisemittedwhenthe unit is generating
ions.
If the sound is irritating, set the unit away from you.
A clicking or ticking sound is
heard from the unit.
TROUBLESHOOTING
ERROR DISPLAY
LAMP INDICATION REMEDY
The “Silent” Fan Speed Indica-
tor Light blinks.
Fan motor is disconnected or abnormal.
Operation stops.
• Pressing the POWER ON/OFF button will reset the error
display, but if error occurs again, contact the shop where
you purchased the unit.
The discharged air has an aroma
or odour.
• Check to see if the filters are heavily soiled.
Replace the filters.
• Plasmacluster Air Purifiers emit small traces of ozone which
mayproducean odour.Theseozone emissions arewellbelow
safety levels .
The unit does not operate when
cigarette smoke is in the air.
• Is the unit installed in a location that is difficult for the sensor
to detect cigarette smoke?
• Is the odour sensor opening blocked or clogged?
(In this case, clean the opening.) (Refer to E-10)
The Plasmacluster Indicator
Light or the CLEAN-SIGN Light
will not activate.
• Check to see if the Lights OFF Mode is selected. If so, then
press the Plasmacluster Ion Mode Selection Button for 3
seconds to activate the indicator lights.
(Refer to E-9)
Plasmacluster Indicator Light
(repeat blue colour cycle light
and shade) • The ION SHOWER operation is working.

SPECIFICATIONS
Model
Power supply
Fan Speed Adjustment
Rated Power
Air Fiow Volume
Applicable Floor Surface
Cord Length
Dimensions
Weight
Fan
Speed
Operation
~19m2*1
2.0m
410mm(W)x158mm(D)x430mm(H)
4.8kg
MAX
26 W
150m3/hour
MED
7.5W
60m3/hour
SILENT
4.1 W
24m3/hour
*1 •The applicable floor surface area is appropriate for operating the unit at maximum fan speed.
•Applicable floor surface area indicates the space where a certain amount of dust particle can be
removed in 30 minutes.
FU-S25E
220-240V 50/60Hz
Standby Power In order to operate the electrical circuits while the power plug is inserted in
the wall outlet, this product consumes about 0.8W of standby power.
For energy conservation, unplug the power cord when the unit is not in use.
E-14

ENGLISH
E-15
A. Information on Disposal for Users (private households)
1. In the European Union
Attention: If you want to dispose of this equipment, please do not use the ordinary dust
bin!
Used electrical and electronic equipment must be treated separately and in
accordance with legislation that requires proper treatment, recovery and recycling of
used electrical and electronic equipment.
Following the implementation by member states, private households within the EU
states may return their used electrical and electronic equipment to designated
collection facilities free of charge*. In some countries* your local retailer may also
take back your old product free of charge if you purchase a similar new one.
*) Please contact your local authority for further details.
If your used electrical or electronic equipment has batteries or accumulators, please
dispose of these separately beforehand according to local requirements.
By disposing of this product correctly you will help ensure that the waste undergoes
the necessary treatment, recovery and recycling and thus prevent potential negative
effects on the environment and human health which could otherwise arise due to
inappropriate waste handling.
2. In other Countries outside the EU
If you wish to discard this product, please contact your local authorities and ask for the
correct method of disposal.
For Switzerland: Used electrical or electronic equipment can be returned free of
charge to the dealer, even if you don’t purchase a new product. Further collection
facilities are listed on the homepage of www.swico.ch or www.sens.ch.
B. Information on Disposal for Business Users.
1. In the European Union
If the product is used for business purposes and you want to discard it:
Please contact your SHARP dealer who will inform you about the take-back of the
product. You might be charged for the costs arising from take-back and recycling.
Small products (and small amounts) might be taken back by your local collection
facilities.
For Spain: Please contact the established collection system or your local authority for
take-back of your used products.
2. In other Countries outside the EU
If you wish to discard of this product, please contact your local authorities and ask for
the correct method of disposal.
Attention: Your product is
marked with this symbol. It
means that used electrical
and electronic products
should not be mixed with
general household waste.
There is a separate
collection system for these
products.

Bitte lesen, bevor Sie Ihr neues
Luftreinigungsgerät in Betrieb nehmen
Das Luftreinigungsgerät saugt Raumluft durch seinen Lufteinlass ein, lässt
diese Luft im Inneren des Gerätes einen Aktivkohlefilter (zur Desodorierung)
und einen HEPA-Filter (zum Entfernen von Schwebeteilchen) passieren und
gibt die gereinigte Luft wieder in den Raum zurück. Mit Hilfe des eingebauten
Ventilators wird dieser Vorgang stetig wiederholt.
Ein neuer HEPA-Filter kann 99,97 % an Schwebeteilchen (bis zu einer Größe
von 0,3 Mikrometer) aus der durchströmenden Luft entfernen. Der
Aktivkohlefilter reinigt die Luft schrittweise von unangenehmen Gerüchten,
wenn diese wiederholt den Filter passiert. (Auch der HEPA-Filter trägt zur
Entfernung von unangenehmen Gerüchen bei.)
Manche ausgefilterten geruchs verursachende Stoffe können sich absetzen
und werden wieder durch den Luftauslass an die Raumluft abgegeben. Je
nach Einsatzbedingungen - insbesondere dann, wenn das Gerät erheblich
stärker als beim Einsatz im Haushalt beansprucht wird - können solche
Gerüche in kurzer Zeit an Intensität gewinnen.
Falls solche Gerüche über längere Zeit auftreten, sind die Filter aufgebraucht
und müssen durch separat erhältliche Austauschfilter ersetzt werden.
DEUTSCH
HINWEIS
•Das Luftreinigungsgerät wurde zur Entfernung von schwebenden Geruchs- und Staubpartikeln, nicht
jedoch zur Entfernung von schädlichen Gasen (zum Beispiel Kohlenmonoxid aus Zigarettenrauch)
aus der Luft entwickelt. Sofern die Ursache des Geruchs bestehen bleibt, kann der Geruch natürlich
nicht vollständig aus der Luft entfernt werden. (Beispiel: Gerüche von Baumaterialien oder durch
Tiere verursachte Gerüche.)
• Wenn Sie rauchen, öffnen Sie am besten das Fenster ein wenig, damit für ausreichende Belüftung
gesorgt ist.
HEPA-Filter
Aktivkohlefilter
N-TINS-A190KKRZ_FU-S25E-G.P65 05.12.7, 7:03 PM2

DEUTSCH
LEISTUNGSMERKMALE
D-1
Vielen Dank für den Kauf des
Luftreinigungsgerätes von SHARP. Bitte
lesen Sie diese Anleitung gut durch, damit
Sie das Gerät problemlos bedienen können.
Bevor Sie das Produkt benutzen, lesen Sie in
jedem Fall den Abschnitt: “Wichtige
Sicherheitshinweise”. Bewahren Sie diese
Anleitung auf, damit Sie später darin nachlesen
können.
WICHTIGE SICHERHEITSHINWEISE. ...... D-2
•WARNUNG ................................................. D-2
•SICHERHEITSHINWEISE FÜR DEN
BETRIEB ..................................................... D-3
•RICHTLINIEN ZUR INSTALLATION ........... D-3
•RICHTLINIEN ZUM UMGANG MIT
FILTERN ..................................................... D-3
BEZEICHNUNGEN DER EINZELNEN
KOMPONENTEN ..................................... D-4
•ANZEIGEN AM HAUPTGERÄT .................. D-4
•EXPLOSIONSZEICHNUNG ....................... D-4
• RÜCKSEITE ............................................... D-5
•IM LIEFERUMFANG ................................... D-5
VORBEREITUNG .................................... D-6
•FILTERINSTALLATION ............................... D-6
BETRIEB ................................................. D-8
•BETRIEB DES HAUPTGERÄTES .............. D-8
PFLEGE UND WARTUNG ..................... D-10
•HAUPTGERÄT .......................................... D-10
•GERUCHSSENSOR ................................. D-10
• PFLEGE DES AUSWASCHBAREN
AKTIVKOHLEFILTERS ............................. D-11
•HINWEISE ZUM FILTERAUSTAUSCH ..... D-12
STÖRUNGSBESEITIGUNG .................. D-13
TECHNISCHE DATEN........................... D-14
ENTSORGUNGSINFORMATIONEN ..... D-15
INHALT
Der neue IONENDUSCHE-Betriebsmodus
gibt konzentrierte Plasmacluster-Ionen frei,
beseitigt Pollen und Schimmel auf effektive
Weise und hemmt obendrein die Aktivität
von schwebenden Viren, Schimmel und
allergieauslösenden Stoffen.
Plasmacluster-Ionen-
Steuerung
Ihr neuer Luftreiniger steuert das
Verhältnis zwischen negativen und
positiven Ionen je nach Raumbedingung.
• Reinigungsmodus
Hierbei werden positive und negative
Ionen zu etwa gleichen Teilen
freigegeben.
•AUTO-Plasmacluster-Ionen-
Modus
Das Gerät schaltet automatisch
zwischen Reinigungsmodus und Ionen-
Steuerungsmodus* um - je nach Stärke
der Luftverunreinigung, die von den
Geruchs- und Staubsensoren erkannt
wird.
* Ionen-Steuerungsmodus
Negative Ionen werden verstärkt
freigegeben und steuern die
Ionenbalance.
•Filter
1) Auswaschbarer Aktivkohlefilter
Absorbiert unangenehme Gerüche.
Der Filter ist auswaschbar, um seinen
Zweck stets optimal erfüllen zu
können.
2) HEPA-Filter (HEPA = High
Efficiency Particulate Air).
Dieser Filter sammelt
Schwebeteilchen auf effektive
Weise - einschließlich Pollen und
Staub.
IONENDUSCHE
N-TINS-A190KKRZ_FU-S25E-G.P65 05.12.8, 10:11 AM3

D-2
Bei der Benutzung von Elektrogeräten sollten Sie sich stets an einige grundlegende
Sicherheitshinweise halten. Dazu zählen die folgenden Dinge:
WARNUNG - Damit es nicht zu Stromschlägen, Bränden oder Verletzungen kommt:
•Lesen Sie sämtliche Anweisungen, bevor Sie das Luftreinigungsgerät benutzen.
•Benutzen Sie ausschließlich eine Steckdose, die 220 bis 240 V führt.
•Benutzen Sie das Luftreinigungsgerät nicht, wenn das Stromkabel beschädigt oder die
Steckdose locker ist.
•Befreien Sie den Anschlussstecker hin und wieder von Staubansammlungen.
•Stecken Sie weder Ihre Finger noch sonstige Fremdkörper in den Lufteinlass oder Luftauslass.
•Wenn Sie den Netzstecker ziehen, greifen Sie ihn grundsätzlich am Stecker selbst, ziehen Sie
niemals am Kabel.
Wenn Sie am Kabel ziehen, können Sie einen Stromschlag bekommen oder einen Kurzschluss
verursachen.
•Berühren Sie den Stecker niemals mit feuchten oder gar nassen Händen.
•Benutzen Sie das Luftreinigungsgerät nicht in der Nähe von Gasgeräten oder offenen Flammen.
•Ziehen Sie den Netzstecker aus der Steckdose, bevor Sie das Gerät reinigen oder wenn Sie es
nicht benutzen.
Wenn Sie dies nicht tun, können Sie durch nicht mehr funktionierende Isolierung einen Stromschlag
bekommen oder einen Brand durch Kurzschluss verursachen.
•Falls das Netzkabel beschädigt wird, muss es durch den Hersteller, eine seiner Service-Nieder
lassungen, einen durch Sharp autorisierten Dienstleister oder eine gleichwertig qualifizierte
Person ersetzt werden, damit es nicht zu Gefährdungen kommt.
•Betreiben Sie das Gerät nicht, wenn Insektenspray benutzt wird, nicht in öligen Räumen, nicht an
Stellen, an denen mit Räucherstäbchen oder glühenden Zigaretten hantiert wird, an denen sich
chemische Dämpfe in der Luft befinden und nicht in feuchten Räumen, wie zum Beispiel Badezimmern.
•Gehen Sie sorgsam vor, wenn Sie den Luftreiniger reinigen. Sehr kräftige Reinigungsmittel können
das Gehäuse beschädigen.
•Wartungsarbeiten an Ihrem Luftreinigungsgerät sollten nur von einem von Sharp autorisierten
Dienstleister durchgeführt werden. Wenden Sie sich an Ihre nächste Service-Niederlassung, falls
einmal Probleme auftreten sollten oder das Gerät justiert oder repariert werden muss-.
HINWEIS - Radio- oder Fernsehstörungen
Falls Ihr Luftreiniger Störungen des Radio- oder Fernsehempfang verursachen sollte, versuchen Sie,
die Störung durch eine oder mehrere der folgenden Maßnahmen zu beheben:
•Richten Sie die Empfangsantenne anders aus oder platzieren Sie diese an einer anderen Stelle.
•Vergrößern Sie den Abstand zwischen Luftreiniger und Radio-/Fernsehempfänger.
•Schließen Sie das Empfangsgerät an einen Stromkreis an, der vom Stromkreis des
Luftreinigungsgerätes getrennt ist.
•Bitten Sie Ihren Händler oder einen erfahrenen Radio-/Fernsehtechniker um Hilfe.
WICHTIGE SICHERHEITSHINWEISE
N-TINS-A190KKRZ_FU-S25E-G.P65 05.12.7, 7:04 PM4