Sharp UP-600 User manual

MODEL UP-600
UP-700
CHAPTER 1. REMOVING THE REAR COVER...............................................1
CHAPTER 2. REMOVING THE TOP CABINET...............................................1
CHAPTER 3. REMOVING THE LCD UNIT......................................................2
CHAPTER 4. REMOVING THE PRINTER UNIT .............................................3
CHAPTER 5. REMOVING THE STANDARD DRAWER unit
(For KA, KB version) ..................................................................4
CHAPTER 6. EXPANSION RAM BOARD : UP-S02MB/04MB ........................5
CHAPTER 7. IN-LINE I/F : UP-E10IN..............................................................5
CHAPTER 8. MCR UNIT : UP-E13MR.............................................................6
CHAPTER 9. POLE DISPLAY UNIT : UP-P16DP............................................7
CHAPTER 10. RE-232 I/F : ER-A5RS, EFT & RS-232 I/F : ER-01EF.............7
CHAPTER 11. HAND SCANNER : ER-A6HS1................................................8
CHAPTER 12. REMOTE DRAWER : ER-04DW/05DW...................................9
CHAPTER 13. RS232DEVICES.......................................................................9
CHAPTER 14. ONE HOLE CLERK KIT : DKIT-8669BHZZ (For UP-600) .....10
CHAPTER 15. DRAWER SEPARATION KIT :
DKIT-3409BHZZ (For KA/KB version) ...................................11
CONTENTS
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified
ones for maintaining the safety and performance of the set.
SHARP CORPORATION This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
UP-700 UP-600

UP-P16DP
UP-E13MR
In-Line cable
RS232devices
ER-A6HS1
and
RS232devices
>>>>> USE FONT <<<<<
Helvetica/ Helvetica-Condensed/ Century-Schoolbook/ Symbol & OriginalFonts: (RingWorld2/RingFont2/Pa
Symbol/PartsCod)
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

CHAPTER 1. REMOVING THE REAR
COVER
1. REMOVING THE REAR COVER
1) Remove the two screws .
2) Remove the rear cover .
2. REPLACING THE REAR COVER
Install the rear cover in the reverse order of removing.
CHAPTER 2. REMOVING THE TOP
CABINET
1. REMOVING THE TOP CABINET
1) Open the printer cover .
2) Lift the pop-up display unit .
3) Remove the three screws .
1
21
1
3
32
3

4) Slightly lift and slide the top cabinet, and remove the grounding
wire .
Note: Do not pull up the top cabinet unit the grounding wire
and connector cables from the top Cabinet are re-
moved.
5) Remove the following cable between the top cabinet and the
main PWB.
Cable between the MAIN PWB and the CKDC PWB.
2. REPLACING THE TOP CABINET
Install the top cabinet in the reverse order of removing.
CHAPTER 3. REMOVING THE LCD
UNIT
1. REMOVING THE LCD UNIT
1) Remove the top cabinet from the bottom cabinet.
2) Remove the LCD flat cable and the earth wire from the
CKDC PWB .
3) Remove the two screws from the LCD HINGE .
4) Remove the LCD unit from the top cabinet.
Insert a flat-bladed screwdriver into the right and left mounting
areas and remove.
4
4
5
3
1
2
4
5

5) With a flat-bladed screwdriver, remove the two latches of each
of the LCD rear cabinet and the LCD filer .
Turn of A and B when you remove it.
2. REPLACING THE LCD UNIT
Install the LCD unit in the reverse order of removing.
CHAPTER 4. REMOVING THE
PRINTER UNIT
1. REMOVING THE PRINTER UNIT
1) Remove the top cabinet.
2) Remove the two screws fixed on the printer unit.
3) Remove the screw fixed on the earth wire .
4) Remove the printer cable from the MAIN PWB (CN9).
2. REPLACING THE PRINTER UNIT
Install the printer unit in the reverse order of removing
6
7
A
B
LCD volum PWB
LCD HS unit
LCD back light
4
11
2
3

CHAPTER 5. REMOVING THE
STANDARD DRAWER
unit (For KA,KB version)
1. REMOVING THE STANDARD DRAWER
UNIT
1) Open the printer cover .
2) Remove the screw fixed on the drawe unit.
3) Stand the main drawer sideways as illusted above, and re-
move the drawer connector from the MAIN PWB (CN:5 ).
2. REPLACING THE STANDARD DRAWER
UNIT
Install the standard drawer unit in the reverse order of removing
The drawer top has the following holes with which the drawer position
can be changed.
A
B
2
2
1
DRCN2
CN4CN5
: Standard position
: Rear position

CHAPTER 6. EXPANSION RAM
BOARD :
UP-S02MB/04MB
1) Open the ROM/RAM case .
2) Install the two spacers on the ROM/RAM PWB unit .
3) Connect the UP-S02MB/04MB to the ROM/RAM PWB unit
(CN:303)
NOTE: The UP-S02MB/S04MB has an electric double layer ca-
pacitor (C21). When removing it after using, use caution
not to bring it close to any conductor.
CHAPTER 7. IN-LINE I/F : UP-E10IN
1) Remove the top cabinet.
2) Install the spacer on the MAIN PWB .
3) Connect the UP-E10IN to the MAIN PWB (CN:304).
4) Fix the UP-E10IN to the spacer with a screw .
5) Pass the TCP/IP cable through the two standard holder
and one core to the following PWB.
UP-E10IN side : CN3, MCR POLE RELAY PWB side :
CN504
7) Remove the rear cover.
8) Connect the LAN cable to the LAN connector .
1
2
3
4
1
2
3
4
5
8
8
9
7
6

9) Install the core to the LAN cable .
NOTE: Install the ferrite core in a position less than 50 mm from
the cabinet.
CHAPTER 8. MCR UNIT : UP-E13MR
1) Align the MCR sheet with the positioning line of the top
cabinet .
2) Mark 3 points of the asterisk mark on the MCR sheet .
3) Aligning with the markings, secure the MCR angle 1 to the
top cabinet with 3 screws .
4) Install the MCR unit to the MCR angle 1 and secure with
2 screws .
5) Remove the rear cover.
6) Connect the MCR cable to the MCR connector .
7) Fix the earth wire to the main chassis with a screw .
8) Install the core to the MCR cable and earth wire with
two wire bands.
10
11
12
IN-LINE cable
Cabinet
Within 50mm
Core
2 2
1
34
4
6
5
7
8
910
11
12

NOTE: Install the ferrite core in a position less than 50 mm from
the cabinet.
CHAPTER 9. POLE DISPLAY UNIT :
UP-P16DP
1) Remove the rear cover.
2) Connect the display cable to the POLE connector .
3) Fix the earth wire to the main chassis with a screw .
4) Install the core to the display cable and earth wire .
Secure the core with two wire bands.
NOTE: Install the ferrite core in a position less than 50 mm from
the cabinet.
CHAPTER 10. RS-232 I/F :ER-A5RS ,
EFT & RS-232 I/F:
ER-01EF
1) Connect the extrnal cables to the I/F board.
<ER-A5RS>
•Install the core (RC0RF6700BHZZ) to the cable with a band.
<ER-01EF>
•Install the core (RC0RF6700BHZZ) to the cable with a band.
NOTE: Install ferrite core in a position less than 10 mm from the
D-sub connector.
Earth wire
Cabinet
MCR cable Wire bandWire band
Core
Within 50mm
2
1
3
5
4
6
Earth wire
Cabinet
MCR cable Wire bandWire band
Core
Within 50mm
Cable
Core
Wire band
D-sub connector
Within 10mm

2) Remove the rear cover.
3) Insert the I/F PWB to the connector of the MAIN PWB
4) Fix the I/F angle to the main chassis with two screws .
CHAPTER 11. HAND SCANNER :
ER-A6HS1
1) Remove the rear cover.
2) Connect the scanner cable to the RS232 CH1 connector.
3) Change the slide switch to the +5V side of the RS232 Relay
PWB unit.
1
24
3
+5V CI
S401
1

CHAPTER 12. REMOTE DRAWER :
ER-04DW/05DW
1) Remove the bottom cabinet from the standard drawer unit.
( Only for KA/KB version)
2) Connect to the remote drawer cable to the drawer connec-
tor of the MAIN PWB (CN:4 or CN5).
3) Fix the earth wire with a screw .
CHAPTER 13. RS232 DEVICES
NOTE: Install the ferrite core in a position less than 10 mm from
the RS232 connector.
For the RS232 Relay PWB, the signals can be switched over
according to the device to be connected.
D-SUB connector
With the switch: S401, the signal to Pin 9 can be switched over
between +5 and CI.
Modular RJ45 connector
With the switches: S403/S404, the signal to Pin 4 can be
switched over between CD, CI, VCC (+5V) and GND.
2
1
3
DRCN2
CN4CN5
Moduler RJ45 connector
D-SUB connector
Cable
Core
Wire band
RS232 connector
Within 10mm
CI
S401
+5V
S403 S404
CI CD
VSC GND

CHAPTER 14. ONE HOLE CLERK KIT : DKIT-8669BHZZ (For UP-600)
No. PARTS CODE NAME Q’ty PRICE NOTE
ONE HOLE CLERK KIT BP
1Connector (5Pin) 1 AE
2Connector (3Pin) 1 AD
3Clerk switch body 1 BH
4Clerk key cable (8pin) (For UP-600) 1 AL
5Clerk angle (For UP-600) 1 AM
6Screw 1 AA
7Clerk cover "B" (For UP-600) 1 AH
8Clerk key No.1 2 AW
Clerk key No.2 2 AW
Clerk key No.3 2 AW
Clerk key No.4 2 AW
Clerk key No.5 2 AW
Clerk key No.6 2 AW
Screw 1 AA UP-600:Not used
Screw 2 AA UP-600:Not used
Clerk key cable (5pin) 1 AN UP-600:Not used
Clerk angle 1 AM UP-600:Not used
"Clerk cover "B" 1 AG UP-600:Not used
"Clerk cover "B" 1 AH UP-600:Not used
1) Solder the connector 5pin and connector 3pin to the
clerk switch body .
2) Connect the clerk key cable 8pin to the clerk switch body
.
3) Install the clerk angle to the clerk switch body with a
screw .
1
2
7
3
4

4) Remove the top cabinet
5) Remove the standard clerk cover from the bottom cabinet.
6) Install the clerk cover "B" to the bottom cabinet.
7) Install the clerk switch body to the bottom cabinet.
8) Connect the clerk key cable 8pin to the CKDC PWB (CN8)
CHAPTER 15. DRAWER SEPARATION KIT : DKIT-3409BHZZ (For KA/KB version)
PARTS LIST
No. PARTS CODE NAME Q’ty PRICE
DRAWER SEPARATION KIT AP
1Gum leg 4 AE
2Screw 3 AA
3Screw 1 AA
1) Remove the standard drawer.
2) Fix the four gum legs with four screws .
4
1
1
1
3
2
2
2
1

COPYRIGHT2001BYSHARPCORPORATION
Allrightsreserved.
PrintedinJapan.
Nopartofthispublicationmaybereproduced,
storedinaretrievalsystem,ortransmitted.
Inanyformorbyanymeans,
electronic,mechanical,photocopying,recording,orotherwise,
withoutpriorwrittenpermissionofthepublisher.
SHARP CORPORATION
Digital Document Systems Group
Quality & Reliability Control Center
Yamatokoriyama, Nara 639-1186, Japan
2001 March Printed in Japan