Sharp AR-160 User manual

•GETTING STARTED
•MAKING COPIES
•STATUS INDICATORS
•GENERAL INFORMATION
•OPTIONAL EQUIPMENT
•APPENDIX
2
13
27
36
53
69
DIGITAL COPYING MACHINE
OPERATION MANUAL
MODEL
AR-160
AR-161
Page

CAUTIONS
Follow the cautions below when using this copier.
●The fusing area is hot. Exercise care in this area when removing misfed paper.
●Do not look directly at the light source. Doing so may damage your eyes.
●Place the copier on a firm, level surface.
●Do not install the copier in a humid or dusty location.
●When the copier is not used for a long time, for example, during prolonged holidays, turn the power
switch off and remove the power cord from the outlet.
●When moving the copier, be sure to turn the power switch off and remove the power cord from the
outlet.
●Do not cover the copier with a dust cover, cloth or plastic film while the power is on. Doing so may
prevent heat dissipation, damaging the copier.
●Use of controls or adjustments or performance of procedures other than those specified herein
may result in hazardous laser radiation exposure.
Cautions on laser
Wave length 785 nm ±10 nm
Pulse times (8.141 µs ±0.1 µs)/7 mm
Output power 0.2 mW ±0.02 mW
Required in Appendix ZB of BS EN 60950 — United Kingdom
MAINS PLUG WIRING INSTRUCTIONS
The mains lead of this equipment is already fitted with a mains plug which is either a non-rewireable
(moulded) or a rewireable type. Should the fuse need to be replaced, a BSI or ASTA approved fuse
to BS1362 marked or and of the same rating as the one removed from the plug must
be used.
Always refit the fuse cover after replacing the fuse on the moulded plug. Never use the plug without
the fuse cover fitted.
In the unlikely event of the socket outlet in your home not being compatible with the plug supplied
either cut-off the moulded plug (if this type is fitted) or remove by undoing the screws if a rewireable
plug is fitted and fit an appropriate type observing the wiring code below.
DANGER: The fuse should be removed from the cut-off plug and the plug destroyed immediately
and disposed of in a safe manner. Under no circumstances should the cut-off plug be inserted
elsewhere into a 13A socket outlet as a serious electric shock may occur.
To fit an appropriate plug to the mains lead, follow the instructions below:
IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:
GREEN-AND-YELLOW: Earth
BLUE: Neutral
BROWN: Live
As the colours of the wires in this mains lead may not correspond with coloured markings
identifying the terminals in your plug, proceed as follows:
The wire which is coloured GREEN-AND YELLOW must be connected to the terminal in the plug
which is marked with the letter E, or by the safety earth symbol Å@, or coloured green or green-
and-yellow.
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter
Nor coloured black.
The wire which is coloured BROWN must be connected to the terminal which is marked with the
letter Lor coloured red.
If you have any doubt, consult a qualified electrician.
WARNING: THIS APPARATUS MUST BE EARTHED.

1
GETTING STARTED STATUS
INDICATORS
MAKING COPIES GENERAL INFORMATION OPTIONAL EQUIPMENT
CONTENTS Page
GETTING STARTED
●INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
●MAIN FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
●PART NAMES AND FUNCTIONS . . . . . . . . . . . . . . . . . . . . 4
– Overall layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
– Operation panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
●COPIER INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . 8
●CAUTIONS ON HANDLING . . . . . . . . . . . . . . . . . . . . . . . . . 9
●LOADING COPY PAPER . . . . . . . . . . . . . . . . . . . . . . 10
MAKING COPIES
●AUDITING ACCOUNTS . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
●NORMAL COPYING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
●REDUCTION/ENLARGEMENT/ZOOM . . . . . . . . . . . . . . . 16
●BYPASS FEED (special paper) . . . . . . . . . . . . . . . . . . . . 18
●TWO-SIDED COPYING . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
●XY ZOOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
●B/W REVERSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
●DUAL PAGE COPY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
●INTERRUPTING A COPY RUN . . . . . . . . . . . . . . . . . . . . . 25
●AUTOMATIC EXPOSURE ADJUSTMENT . . . . . . . . . . . . 26
STATUS INDICATORS
●TD CARTRIDGE REPLACEMENT . . . . . . . . . . . . . . . 27
●DRUM CARTRIDGE REPLACEMENT . . . . . . . . . . . . 29
●MISFEED REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . 31
●MAINTENANCE REQUIRED . . . . . . . . . . . . . . . . . . . 35
GENERAL INFORMATION
●USER PROGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
– Settings for auditing accounts . . . . . . . . . . . . . . . . . . . . . . . 39
●POWER SAVE MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
●USER MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
●COPIER TROUBLE? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
●SUPPLIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
– Types and sizes of copy paper . . . . . . . . . . . . . . . . . . . . . . . 49
– Genuine supplies statement . . . . . . . . . . . . . . . . . . . . . . . . . 50
●SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
OPTIONAL EQUIPMENT
●SYSTEM CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . 54
●SINGLE PASS FEEDER (AR-SP2) . . . . . . . . . . . . . . . . . . 55
●ELECTRONIC SORTING KIT (AR-EB3) . . . . . . . . . . . . . . 58
– Sort/group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
– 2 in 1 or 4 in 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
– Erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
– Margin shift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
●250-SHEET PAPER FEED UNIT (AR-DE5)/
2x250-SHEET PAPER FEED UNIT (AR-DE6) . . . . . . . . . . 66
APPENDIX
●TRANSFER CHARGER CLEANING . . . . . . . . . . . . . . . . . 69
●DRUM CARTRIDGE LIFE . . . . . . . . . . . . . . . . . . . . . . . . . 70
●INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
APPENDIX

2
GETTING STARTED
INTRODUCTION
This copier has been designed to provide convenient copying features in a minimum amount
of office space and with maximum operational ease. To get full use of all copier features,
be sure to familiarise yourself with this manual and the copier.
For quick reference during copier use, keep this manual in a handy location.
This copier can be used as a laser printer and as a facsimile machine by installing optional
components.However, this manual describes only the copier features. For description of the printer
features and facsimile features, see their separate manuals.
Conventions used in this manual
In this manual, the following icons are used to provide the user with
information pertinent to the use of the copier.
Introduction
Warns the user that injury to the user or damage to the
copier may result if the contents of the warning are not
properly followed.
Cautions the user that damage to the copier or one of its
components may result if the contents of the caution are
not properly followed.
Notes provide information relevant to the copier regarding
specifications, functions, performance, operation and
such, that may be useful to the user.
Indicates a letter displayed in the copy quantity display.

3
GETTING STARTED
MAIN FEATURES
qHigh-speed laser copying
●First-copy time is only 7.2 seconds (except in a power save mode or immediately after power on).
●Copying speed is 16 copies/min., which adapts to business use, allowing improvement of working efficiency.
wHigh-quality digital image
●High-quality copying at 600 dpi is performed.
●In addition to the automatic exposure mode, the manual exposure can be adjusted in five steps.
●The photo mode copying function allows clear copying of delicate halftone original images such as monochrome
photos and colour photos. Photo mode is adjustable in five steps.
eSubstantial copying features
●Zoom copying from 50% to 200% in 1% increments can be performed.
●Continuous copying of maximum 99 sheets can also be performed.
●Useful special features such as the XY zoom, black and white reverse, and dual page copy are available.
●User programs allow setting/modification of functions for customer needs. Also the user programs allow the internal
auditor to be controlled.
rOptional features
●An optional single pass feeder (SPF) allows automatic document feeding of up to 30 sheets.
●An optional electronic sorting kit allows many useful copier features to be used. Multiple sets of copies can be sorted
without the aid of a sorter and each set can be offset from the previous set. (The offset feature is provided only with the
AR-161.) Also the erase, margin shift, and 4 in 1 and 2 in 1 functions are available. (To use the 2 in 1 and 4 in 1 and sort/
group functions, an optional SPF is also needed.)
●This copier can be used as a laser printer by installing an optional printer expansion kit.
●This copier can be used as a facsimile machine by installing an optional facsimile expansion kit.
tEnvironmentally friendly design
●Paper output tray is housed in the copier for space saving.
●Preheat mode and auto power shut-off mode are provided to reduce power consumption in standby mode.
This copier does not have an internal calendar or clock.
This copier will not be affected by the year 2000.
Main features

4
GETTING STARTED
PART NAMES AND FUNCTIONS
Overall layout
qPlaten cover
Place the original on the original table and close the
platen cover before copying starts.
wOriginal table
Place the document to be copied here.
eHandles
Use to move the copier.
rPower switch
Press to turn copier power on and off.
tOperation panel
All copier controls are located here for easy operation.
yPaper output tray
Finished copies are deposited in the paper output tray.
uFront cover
Open to remove misfeeds and for copier servicing.
iPaper tray
Holds 250 sheets of copy paper.
oSide cover
Open to remove misfeeds and to service the copier.
!0 Side cover handle
Lift and pull to open the side cover.
!1 Bypass tray guides
Adjust to the width of the copy paper.
!2 Bypass tray
Special papers (including transparency film) and copy
paper can be fed from the bypass tray.
!3 Bypass tray extension
Pull out when feeding large paper such as B4 and A3.
!4 Charger cleaner
Use to clean the transfer charger.
GETTING STARTED
q
w
e
e
r
t
y
!2
!3
!4
o
u
!0
!1
i
Part names and functions

5
GETTING STARTED
PART NAMES AND FUNCTIONS
!5 Drum cartridge handle
Hold to pull out the drum cartridge.
!6 Drum cartridge
Copy images are formed on the photoconductive drum.
!7 TD cartridge lock release lever
Use to unlock the TD cartridge.
!8 TD cartridge strap
Lift to remove the TD cartridge.
!9 TD cartridge
Contains toner.
@0 Roller rotating knob
Turn to remove misfed paper.
@0 @1
@2
!5
!6
!7 !8
!9
@1 Fusing unit release levers
Lower to remove misfed paper.
The fusing unit is hot.
Take care in removing paper.
@2 Paper guide
Open to remove misfed paper.
Accessories
Operation manual. . . . . . . . . . . . . . . . . . . . . . . 1
TD cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Charger cleaner . . . . . . . . . . . . . . . . . . . . . . . . 1
Part names and functions
GETTING STARTEDGETTING STARTED

6
GETTING STARTED
Operation
panel
PART NAMES AND FUNCTIONS
qINTERRUPT key and indicator (p. 25)
Interrupts a copy run.
wCopy quantity display
Displays the specified copy quantity during the ready
condition and displays the copy countdown as copies
are made. Also see items rand @1.
eZOOM indicator (p.17)
Lights up when a zoom ratio is set.
rCopy ratio display key (p. 17)
Press and hold down during standby to display the copy
ratio in the copy quantity display.
tZoom keys (p. 17)
Use to select any reduction or enlargement copy ratio
from 50% to 200% in 1% increments.
yPAPER SIZE ENTER key (p.12)
Use to set the paper size in a tray.
uAUDIT CLEAR key (p.13)
Closes an open account.
iPAPER SIZE indicators
Light up to show the selected copy paper size.
oAlarm indicators
: Maintenance indicator (p.35)
: TD cartridge replacement required indicator
(p.27)
: Drum replacement required indicator (p.29)
: Paper required indicator (p.10)
: Misfeed indicator (p.31)
!0 POWER SAVE indicator (p. 43)
Lights up when the copier is in a power save mode.
!1 SPF indicator (p. 56)
Lights up when originals are set in the optional SPF tray.
!2 Output tray full indicator (p. 59)
Indicates copies must be removed from the paper output
tray.
!3 B/W REVERSE key and indicator (p. 23)
Press to reverse the black and white areas.
!4 XY-ZOOM key and indicator (p. 21)
Press to change the horizontal and vertical copy ratios
independently.
!5 SORT/GROUP key and indicators (p. 59)
Press to select the sort or group mode when an optional
electronic sorting kit and an optional SPF are installed.
!6 ORIGINAL DATA indicator
Blinks when the memory becomes full of scanned
original image data. (Used when an optional electronic
sorting kit and an optional SPF are installed)
!7 2 IN 1 / 4 IN 1 key and indicators (p. 61)
Press to select the 2 in 1 or 4 in 1 mode. (Only available
when an optional electronic sorting kit and an optional
SPF are installed)
!8 AUTO/MANUAL/PHOTO key and indicators
(p. 14)
Use to sequentially select the exposure modes: AUTO,
MANUAL, or PHOTO.
!9 Light and dark keys and indicators (p. 15)
Use to adjust the MANUAL or PHOTO exposure level.
@0 Numeric keys
Use to select the desired copy quantity or to make user
program entries.
@1 Zero key
Use as part of numeric keys to enter copy quantity.
Press during a continuous copy run to display the
number of copies completed in the current run.
Press during standby to display the total output count.
GETTING STARTED Part names and functions
w r o !1!0te
!8 @7 @8 #0@2 @4!9 @1 @3 @5 @6 @9@0
y u !2iq
Not used for the copier features.

7
GETTING STARTED
PART NAMES AND FUNCTIONS
Press and hold down the key. 12,345 sheets output
1st display 2nd display
Note: A3 size copies are counted as two copies.
@2 CLEAR key
Clears the copy quantity display or terminates a copy
run.
@3 START key and indicator
Copying is possible when the indicator is on.
Press to start copying.
@4 CLEAR ALL ( ) key
Clears all selected settings and returns the copier to the
initial settings.
@5 PRESET RATIO selector keys and indicators
(p. 17)
Use to sequentially select preset reduction/enlargement
copy ratios: 50%, 70%, 81%, 86%, 100%, 115%, 122%,
141%, 200%.
@6 ORIGINAL SIZE ENTER key and indicators
(p. 14, 16)
Use to input the original size for automatic paper selec-
tion and automatic copy ratio selection.
@7 AUTO PAPER SELECT indicator
Paper of the proper size will be automatically selected
depending on the original size and selected copy ratio
when this indicator is on.
@8 TRAY SELECT key (p. 14)
Use to manually select a paper tray.
@9 AUTO IMAGE key and indicator
Press for automatic copy ratio selection.
#0 Paper feed location/misfeed location indica-
tors (p. 31)
The selected paper feed location is shown by a lit
indicator ( ).
The general location of misfed paper is shown by a
blinking red indicator ( ).
#1 DUAL PAGE COPY key and indicator (p. 24)
Use to make individual copies of two originals placed
side by side on the original table.
#2 ERASE key and indicators (p. 63)
Press to select the edge erase and/or the centre erase
mode. (Only available when an optional electronic
sorting kit is installed)
#3 MARGIN SHIFT key and indicator (p. 65)
Shifts text or image on the copy to leave a binding
margin on the left side of the copy. (Only available
when an optional electronic sorting kit is installed)
Initial settings
The copier assumes the initial settings when it is first turned
on, when the CLEAR ALL ( ) key is pressed, and ap-
proximately one minute* after the last copy is made in any
mode.
●Copy ratio: 100%
●Exposure: Automatic
●Copy quantity: 0
●All special copier modes: Off
●Auto paper selection : On
●Paper feed station: Previously selected paper tray
* This time (auto clear time) can be changed. See page 36,
USER PROGRAMS.
Part names and functions
GETTING STARTEDGETTING STARTED
!7!6!5!3
#1 #2 #3
!4

8
GETTING STARTED Copier installation
COPIER INSTALLATION
Improper installation may damage the copier. Please note the following
during initial installation and whenever the copier is moved.
If the copier is moved from a cool place to a warm place, condensation may form inside the copier.
Operation in this condition will cause poor copy quality and malfunctions. Leave the copier at room
temperature for at least 2 hours before use.
Do not install your copier in areas that are:
●damp, humid, or very dusty
●exposed to direct sunlight
●poorly ventilated
●subject to extreme temperature or humidity changes, e.g., near an
air conditioner or heater.
The copier should be installed near an accessible power outlet
for easy connection.
Be sure to connect the power cord only to a power outlet that
meets the specified voltage and current requirements.
Also make certain the outlet is properly grounded.
Connect the copier to a power outlet which is not used
for other electric appliances. If a lighting fixture is
connected to the same outlet, the light may flicker.
Be sure to allow the required space around the machine for
servicing and proper ventilation.
A small amount of ozone is produced within the copier during operation.The emission level is insufficient
to cause any health hazard.
NOTE:
The present recommended long term exposure limit for ozone is 0.1 ppm (0.2 mg/m3) calculated as
an 8 hr. time-weighted average concentration.
However, since the small amount that is emitted may have an objectionable odor, it is advisable to
place the copier in a ventilated area.
10 cm

9
GETTING STARTED
CAUTIONS ON HANDLING
Be careful in handling the copier as follows to maintain the performance of
this copier.
Do not drop the copier, subject it to shock or strike it against any
object.
Do not expose the drum cartridge to direct sunlight.
Doingsowill damage thesurface(greenportion) of thedrumcartridge,
causing poor copy quality.
Store spare supplies such as drum cartridges and TD cartridges
in a dark place without removing from the package before use.
If they are exposed to direct sunlight, poor copies may result.
Do not touch the surface (green portion) of the drum cartridge.
Doing so will damage the surface of the cartridge, causing smudges
on copies.
Cautions on handling

10
GETTING STARTED
LOADING COPY PAPER
To save space, this copier has been designed with an adjustable front-loading
tray, which is easily opened for paper loading. For best results, use only
SHARP recommended paper. (See page 49.)
The paper required ( ) indicator will light up when there is no copy paper
in the selected paper feed station, or when the selected paper tray is not
installed or is improperly installed.
When the paper size is changed in a paper tray, the size
of the paper must be entered by steps 8 through 11 on
page 12. If not, the edges of copies may become
smudged with toner. Also, the AUTO PAPER SELECT
and the AUTO IMAGE features will not function properly.
1Gently lift and pull out the paper tray until it stops.
2Push the pressure plate down until it locks in place.
3Fan the copy paper and insert it into the tray. Make sure
the edges go under the corner hooks.
●If you change to a different size of copy paper, the tray must be
adjusted. See the next page.
●Set the paper along the guides.
●The tray holds up to 250 sheets of paper.
Do not load paper above the maximum height line.
4Push the paper tray firmly back into the copier.
Loading copy paper
Maximum height line

11
GETTING STARTED
Changing the copy paper size in the tray
1Gently lift and pull out the paper tray until it stops.
2Push the pressure plate down until it locks in place.
3Squeeze the lock lever of the front guide and slide the
front guide to match the width of the paper.
4Move the left guide to the appropriate slot as marked
on the tray.
●When using A5 copy paper, load it into the uppermost paper tray. If
other trays (including trays in optional paper feed units) are used,
paper misfeeds may occur.
5Load copy paper into the tray.
6Place the appropriate label to indicate the selected
paper size into the recess on the right front side of the
paper tray.
7Push the paper tray firmly back into the copier.
Loading copy paper
LOADING COPY PAPER
Front guide
Left guide

12
GETTING STARTED Loading copy paper
LOADING COPY PAPER
8To set the selected paper size, press the PAPER SIZE
ENTER key.
●The selected paper feed location indicator will blink and the corre-
sponding paper size (which is currently set) indicator will light up
steadily. All other indicators will go out.
For paper size setting, ensure that the COPY mode
has been selected. However, if copying, printing or
facsimile printing is being performed, paper size setting
cannot be made even in the COPY mode. See Note
on page 47.
9Use the TRAY SELECT key to select the paper tray of
which the paper size has been changed.
●Each time the TRAY SELECT key is pressed, a paper tray will be
indicated with a blinking paper feed location indicator. If an optional
paper feed unit is not installed, this operation is not needed.
10
Use the ORIGINAL SIZE ENTER key to select the paper
size which is set.
●Each time the ORIGINAL SIZE ENTER key is pressed, a paper size
will be indicated with a paper size indicator.
11
Press the START key and then the PAPER SIZE ENTER
key.
●To change the paper size setting of another tray, repeat steps 9 to 10
after pressing the START key.

13
MAKING COPIES
AUDITING ACCOUNTS
If this copier has been programmed in the auditing mode, it will not function
until an assigned 3-digit account number has been entered. See page 39 for
setting the auditing mode.
If the copier has been programmed in the auditing mode, “–––” will appear
in the copy quantity display in the initial conditions.
1Enter your account number using the numeric keys.
●As each digit is entered, the dashes in the copy quantity display will
disappear.
●After the number is entered, the copy quantity display will change
to 0.
●If an unassigned number is entered, “–––” will appear again in the
copy quantity display, indicating that the number was not accepted.
2When copying is completed, press the AUDIT CLEAR
key.
●“–––” will appear again in the copy quantity display, indicating the
auditing mode.
●In the interrupt copy mode (see page 25), press the INTERRUPT key
after an interrupt copy run is completed. All previous copier settings
will be restored and the previous account number will be active.
Auditing accounts

14
MAKING COPIES
NORMAL COPYING
1Turn the power switch on.
●It will take about 35 seconds for the copier to warm up. However, you
can make desired settings and press the START key during warm-up.
Copying will start after warm-up.
●If the copier has been programmed in the auditing mode, the START
key indicator will not light up and “–––” will appear in the copy
quantity display. Enter an assigned 3-digit account number. See page
13.
●If the power is already on and all indicators except the POWER SAVE
indicator are off, the copier is in the auto power shut-off mode. Press
the START key in this case. See page 43, POWER SAVE MODES.
2Place the original face down on the original table. Align
it with the original size scale.
●Image loss (max. 4 mm) can occur at the leading and trailing edges of
the copies. Also image loss (max. 4 mm in total) can occur along the
other edges of the copies.
3Close the platen cover.
4Ensure that the copy paper size in the paper tray is the
same size as the original.
●If a tray of the required size is not installed, use the bypass tray and
press the TRAY SELECT key to select the bypass tray.
●If an optional paper feed unit is installed:
Use the ORIGINAL SIZE ENTER key to select the original size.
Copy paper of the same size as the original will be automatically
selected. If desired, another paper tray can be selected by pressing the
TRAY SELECT key.
5Adjust the copy density.
●This copierhasthreeexposure modes tochoosefrom — AUTOMATIC,
MANUAL, and PHOTO.
●Automatic exposure is the standard initial setting for this copier. In this
mode, the characteristics of the original are “read” by the exposure
system and adjustments are automatically made. This optimizes the
contrast of the copied images by reducing the effect of coloured or
shaded background areas. See page 26 to adjust the automatic expo-
sure level.
Normal copying
Power on

15
MAKING COPIES
●For manual copy density adjustment, press the AUTO/MANUAL/
PHOTO key to select MANUAL and adjust with the light ( ) and
dark ( ) keys as desired.
6Set the number of copies using the numeric keys.
●A single copy can be made with the initial setting, i.e., when “0” is
displayed.
●Press the CLEAR ( ) key to clear an entry if a mistake is made.
7Press the START key.
●The number in the copy quantity display will decrease by 1 each time
a copy is made.
●Press the CLEAR key to stop copying in the middle of a run.
●To repeat the same copy sequence for a different original, simply
replace the original and press the START key.
How to remove the platen cover
The platen cover can be removed to allow copying of
bulky objects. To remove it, simply lift the platen cover
straight up.
●To reattach the platen cover, reverse the above procedure.
NORMAL COPYING
●For photographs, select PHOTO and then adjust with the light ( )
and dark ( ) keys as desired.
●There are 5 exposure steps indicated by 3 indicator lights. (The
indicators light up one or two at a time.)
If exposure level 2 is selected, the two left-handmost indicators for that
level will light up simultaneously. Also, if level 4 is selected, the two
right-handmost indicators for that level will light up simultaneously.
Normal copying

16
MAKING COPIES
REDUCTION/ENLARGEMENT/ZOOM
Reduction and enlargement ratios can be selected either automatically with
the AUTO IMAGE key or manually with the PRESET RATIO selector
( , ) keys and/or the zoom ( , ) keys. The zoom function enables
precise copy ratio selection from 50% to 200% in 1% increments.
Reduction/enlargement/zoom
Automatic
1Place the original on the original table and close the
platen cover.
2Press the ORIGINAL SIZE ENTER key until the indicator
for the size of the original on the original table lights up.
3Use the TRAY SELECT key to select the paper tray with
the desired paper size.
●This feature will not work when copy paper of non-standard size is
used or the bypass tray is used.
4Press the AUTO IMAGE key.
●The copy ratio will be automatically set.
●If the size and orientation of the original do not correspond to standard
reduction/enlargement ratios for the selected paper tray, then the
ORIGINAL SIZE indicator will blink.
However, if an optional electronic sorting kit is installed, the original
image may be automatically rotated.
●If a PRESET RATIO indicator is blinking, part of the original image
may not be copied.
5Enter the number of copies.
6Press the START key.
●To cancel the automatic reduction/enlargement
mode, press the AUTO IMAGE key again.
●WhencopyingfromanoptionalSPFwiththisfeature,
the automatic reduction/enlargement mode will be
automatically cancelled after copying is complete.

17
MAKING COPIES
REDUCTION/ENLARGEMENT/ZOOM
Reduction/enlargement/zoom
Manual
1Place the original on the original table and close the
platen cover.
2Use the PRESET RATIO selector ( , ) keys and the
zoom ( , ) keys to select the desired copy ratio.
●To select a preset reduction or enlargement copy ratio, press the
or key repeatedly until the indicator for the desired copy ratio is lit.
A. Preset reduction ratios are: 86%, 81%, 70%, and 50%.
B. Preset enlargement ratios are: 115%, 122%, 141%, and 200%.
C. Zoom ratios: Any ratio from 50% to 200% can be set, in 1%
increments. Press the or key to set the approximate
ratio, then press the key to decrease the ratio or the key
to increase the ratio.
●When a zoom ( , ) key is pressed, the ZOOM indicator will light
up and the zoom ratio will be displayed in the copy quantity display for
at least two seconds.
●To verify a zoom setting without changing the zoom ratio, press and
hold down the copy ratio display ( ) key. When the key is released,
the display will return to the copy quantity display.
●To decrease or increase the zoom ratio rapidly, press and hold down
the or key. However the value will stop at the preset reduction
or enlargement ratios. To move beyond these ratios, release the key
and then press and hold it down again.
D. Same-size reset: Press the or key repeatedly until the
copy ratio returns to 100%.
3Ensure that copy paper of the desired size is installed in
the paper tray.
●If an optional paper feed unit is installed:
Use the ORIGINAL SIZE ENTER key to select the original size.
Copy paper of the appropriate paper size will be automatically selected
depending on the original size and copy ratio. If the selected PRESET
RATIO indicator or the ZOOM indicator blinks, the selected copy
image is too large for the copy paper size.
The desired paper tray can also be selected by pressing the TRAY
SELECT key.
4Set the number of copies and press the START key.

18
MAKING COPIES
1Unfold the bypass tray.
●When feeding B4 or A3 sized paper, extend the feeder tray.
2Set the paper guides to the copy paper width.
3Insert the copy paper (print face down) all the way into
the bypass tray.
●Up to 100 sheets of standard copy paper measuring from A6 to A3 can
be loaded in the bypass tray.
●A6 size paper must be fed narrow into the feed slot.
●Transparency film, labels, and other special purpose papers (except
envelopes) must be fed individually.
Up to 10 envelopes can be set.
●When adding paper, first remove remaining paper, combine it with the
paper to be added and then reload as a single stack.
●When loading envelopes, make sure that they are straight and flat.
Bypass feed (special paper)
BYPASS FEED (special paper)
The bypass tray is used to copy onto transparency film, labels, and other
special purpose papers. Up to 100 sheets of standard copy paper can be set
in the bypass tray.
For special purpose papers, the original image must be
smaller than the paper or media for copying.
If the original image is bigger than the paper or media, this
may cause smudges on the edges of the copies.
Also for standard copy paper, smudges may appear if the
copy paper is not at least as large as the original image.