Sharp CD-BA1300H User manual

– 7 –
CD-BA1300H
Check the supplied accessories
AM loop aerial ×1
FM aerial ×1
Remote control ×1
AC power lead ×1
Putting batteries into the remote control
2 "AA" size batteries
(UM/SUM-3, R6, HP-7 or similar)
1 Remove the battery cover.
2 Insert the batteries.
3 Replace the battery cover.
1
2
[For U.K.]
AC power lead ×1
[Except for U.K.]
Placing the system
10 cm (4")
10 cm (4")
3
10 cm (4")
10 cm (4")
Left speaker
Black
Connections
4
AC 230 V, 50 Hz
1 Connect the AM and FM aerials.
2 Connect the speaker system.
3 Connect the AC power lead.
Right speaker
AM loop
aerial
FM aerial
1
2
Red
[For U.K.] [Except for U.K.]

CD-BA1300H
– 8 –
7
Listening to a tape
1 Press the ON/STAND-BY button to turn the power on.
4 Press the TAPE (1 2) button to select the TAPE 1
or TAPE 2.
3 Load the cassette into the TAPE 1 or TAPE 2 cassette
compartment.
2 Open the cassette door by pushing the area marked
"PUSH EJECT".
5 Press the button to start playback.
1 Press the ON/STAND-BY button to turn the power on.
2 Press the TUNER (BAND) button to select FM ST, FM
or AM.
4 Adjust the sound volume using the VOLUME buttons.
6 Adjust the sound volume using the VOLUME buttons.
3 Press the TUNING/TIME ( or ) button to tune in-
to the desired station.
Listening to the radio
6
1 Press the ON/STAND-BY button to turn the power on.
2 Press the CD button.
3 Press the OPEN/CLOSE button to open the disc tray.
4 Place the CD(s) on the disc tray, label side up.
5 When loading a third disc, press the DISC SKIP button
to turn the disc tray, then place the CD in the open pos-
ition.
6 Press the OPEN/CLOSE button to close the disc tray.
Listening to a CD
5
7 Press the button.
8 Adjust the sound volume using the VOLUME buttons.
And then, close the cassette door completely until it is locked.
1
2
4
3
TAPE 1 TAPE 2
PUSH
EJECT
PUSH
EJECT
1
5
6
3
2
3
4
2
4
1
2
53,6
7
8
5
12 cm (5")
8 cm (3")
Resetting the microcomputer
1
Press the ON/STAND-BY button to enter the stand-by
mode.
2
Whilst pressing down the button and the
EQUALIZER/X-BASS/DEMO button, hold down the
ON/STAND-BY button for at least 1 second.
"CLEAR AL" will appear.
Caution:
The operation explained above will erase all data stored
in memory including clock and timer settings, and tuner
and CD presets.
If this product is subjected to strong external interference
(mechanical shock, excessive static electricity, abnormal
supply voltage due to lightning, etc.) or if it is operated in-
correctly, it may malfunction or the display may not func-
tion correctly. If such a problem occurs, do the following:
CD pickup cleaning
1 Press the ON/STAND-BY button to turn the power on.
3 Press the CD button and load the desired disc.
2 Load a cassette into the TAPE 2 cassette compartment.
4 Press the REC PAUSE button.
5 Press the button.
Recording from CDs
8
Clean the dust or stain on the CD pickup lens
using a commercial cleaning disc (brush type).
Cleaning disc
TAPE 2
PUSH
EJECT
1
5
4
2
3
1,2
2
2