Shure DT15P User manual

SPECIFICATIONS DTl5P DT25P DT35P SPECIFICATIONS DTl5P DT25P DT35P
Frequency Response 20-20,000 Hz 15-22,000Hz 15-27,000 Hz RecommendedCapacitive 200-300pF 200-300
pF
200-300 pF
Output
@
1 kHz, 5 cmlsec 5.0 mV 5.0 mV 5.0 mV Load
Channel Separation Stylus Tip Shape 0.4
x
0.7 mil 0.3
x
0.7 mil 0.2
x
1.5 mil
@IkHz 20 dB 22 dB 24 dB Biradial Biradial Hyper-Ridge
(15 dB
@
10 Elliptical Elliptical
kHz) Stylus Grip Color Burnt Orange Gray Red
Channel Balance Within 2 dB Within 2
dB
Within 1.5 dB
~artridge~eight*~
5.9 grams 5.9 grams 5.9 grams
Tracking Force 1.25 grams 1.25grams 1.25grams Recommended Replace- N94LT N96LT N97LT
Trackability
@
400 Hz 19 cmlsec 22 cmlsec 24 cmlsec ment Stylus (Blue Grip) (Yellow Grip) (RedGrip)
Recommended Load
47
kfl 47 kfl 47 kfl
Impedance 'Without adapter cartridge is compatible with P-Mount arms. With adapter
cartridge is compatible with %-inchmount arms
Copyright
1987,
Shure Brothers Inc.
27A2247
(G
L)
Printed inU.S.A.

INSTRUCTIONS
The DT15P, DT25P, and DT35Pcartridges are com-
patible with P-Mount arms and with %-inch
standard-mount arms (using the supplied
adapter). Be sure to remove the stylus before
mounting the cartridge. Carefully replace the
stylus after mounting iscomplete.
There are three basic methods of mounting the
cartridge.
A. In a headshell with
unthreaded mounting
holes
/';
@%
--------
1
Electrical connections,l
Methods A and B 1
B. Ina headshell with
I I
threaded mountingl WHITE I
holes
I
BLUE 1
C. In a P-Mount arm
,
TRACKING FORCE IN A P-MOUNT ARM
After mounting the cartridge, it is not usually
necessary to adjust the tracking force ina pre-set
arm.
TO PRESERVE STYLUS LIFE
1. Protect stylus with stylus guard when dusting
turntable.
2. Regulate tone arm, set-down or changer
mechanism to prevent stylus from striking
edge of turntable or record.
3. Do not handle tone arm while record is being
played; handling may cause arm to sweep
across record. Use cuing device if available.
4. If manual set-down is necessary, release arm
as soon as stylus engages groove.
5. Do not activate arm without record on turn-
table.
6. Do not stack more records than changer
manufacturer recommends.
7. Do not use damaged records.
8. Make certain cartridge iscorrectly mounted in
tone arm; make certain stylus is properly in-
serted in cartridge.
9. Use appropriate vertical tracking force for
each cartridge and stylus; forces outside
recommended range can cause stylus and
record damage.
10. Follow turntable or tone arm instructions for
antiskating force (where applicable).
SPECIAL NOTE
To maintainthe original performance standards of
your cartridge, be certain that any replacement
stylus you buy bears the following certification on
the package: "This Stereo Dynetic@stylusis preci-
sion manufactured by Shure Brothers Inc." AVOID
INFERIOR IMITATIONS. THEY WILL SERIOUSLY
DEGRADETHE PERFORMANCEOFYOURCAR-
TRIDGE. ALL GENUINE DYNETIC@STYLI ARE
MANUFACTURED BY SHURE BROTHERS INC.
LOOK FOR THE NAME SHURE ON THE STYLUS
GRIP.
FULL ONE-YEAR WARRANTY: Shure Brothers
lncorporated ("Shure"), 222 Hartrey Avenue,
Evanston, lllrno~s60202-3696, warrants to the
owner of th~sproducf ma7 itwill be free, innormal
use, of any defects Inworkrnansh~pand mater~als
for a per~odof one year fromdate of purchase You
should retain proof of date of purchase Shure is
not liable for any consequent~aldamages If thls
Shure product has any defects as descr~bed
above, carefully repack the un~tand return ~t
prepaid to:
Shure Brothers lncorporated
Attention: Service Department
222 Hartrey Avenue
Evanston, IL60202-3696U.S.A.
If you are not in the United States, return the unit
to your dealer or Authorized Service Center for
repair. The unit will be repaired or replaced and
returned to you promptly, and if it cannot be
repaired or replaced, you may elect toreceive a re-
fund. This warranty does not include stylus wear.