Shure AD1 User manual

WARNING
• Battery packs may explode or release toxic materials. Risk of fire or
burns. Do not open, crush, modify, disassemble, heat above 140°F
(60°C), or incinerate.
• Follow instructions from manufacturer
• Only use Shure charger to recharge Shure rechargeable batteries
• WARNING: Danger of explosion if battery incorrectly replaced. Replace
only with same or equivalent type.
•Never put batteries in mouth. If swallowed, contact your physician or local
poison control center
• Do not short circuit; may cause burns or catch fire
• Do not charge or use battery packs other than Shure rechargeable bat-
teries
• Dispose of battery packs properly. Check with local vendor for proper
disposal of used battery packs.
• Batteries (battery pack or batteries installed) shall not be exposed to
excessive heat such as sunshine, fire or the like
WARNING: Danger of explosion if incorrect battery replaced. Operate only
with AA batteries.
Note: Use only with the included power supply or a Shure-approved equiva-
lent.
Please follow your regional recycling scheme for batteries, packaging, and
electronic waste.
WARNING:This product contains a chemical known to the State of California
to cause cancer and birth defects or other reproductive harm.
低功率電波輻射性電機管理辦法
第十二條
經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得
擅自變更頻率、加大功率或變更原設計之特性及功能。 第十四條
低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現
象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依
電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科
學及醫療用電波輻射性電機設備之干擾。
AD1 Axient Digital Bodypack Transmitter
AD series bodypack transmitters deliver impeccable audio quality and RF
performance with wide-tuning, High Density (HD) mode, and encryption. The
transmitter features durable metal construction, AA or SB900A rechargeable
power (with dockable charging), and TA4 or LEMO3 connector options.
Features
Performance
• 20 Hz to 20 kHz range with flat frequency response
• Automatic input staging optimizes gain setting
• AES 256-bit encryption-enabled for secure transmission
• >120 dB dynamic range
• 100 meter (300 feet) line-of-sight operating range
•Selectable modulation modes optimize performance for spectral efficiency
⁃ Standard – optimal coverage, low latency
⁃ High density – dramatic increase in max system channel count
• Built-in tone generator and RF markers to facilitate walk-testing
• Switchable Power Levels = 2/10/35 mW (region dependent)
• Frequency Diversity selection using two bodypacks
Design
• TA4 or LEMO3 audio connector option
• Backlit LCD with easy to navigate menu and controls
• Rugged metal construction
• Flexible ¼ wave antenna
• Menu and power lockout
Power
• Over 8 hours continuous use with 2 x AA alkaline batteries
•Shure SB900A lithium-ion rechargeable battery provides extended battery
life, precision metering, and zero memory effect
• External charging contacts for docked charging
Included Components
80B8201AA alkaline batteries (2)
Varies by Region¼ wave antenna
WA340Threaded TAF4 adapter
WA610Transmitter carrying case
26A13Zipper bag
44A12547Belt clip
Optional Accessories
1/12©2016 Shure Incorporated
AD1
AD1 Bodypack Transmitter

SB900ABodypack rechargeable lithium-ion battery
AXT652Y-Cable for bodypack transmitters
AXT652LEMO3LEMO Y-cable for bodypack transmitters
WA302Instrument cable
44A12547Replacement belt clip
WA304
Instrument cable with right angle 1/4"
connector
WA661Mute Switch for Bodypack
WA662Mute Switch for 2 Bodypacks
AD1 Transmitter Overview
① RF Antenna
For RF signal transmission.
② Display
View menu screens and settings. Press any control button to activate the
backlight.
③ Infrared (IR) Port
Align with the receiver IR port during an IR Sync for automated transmitter
tuning and setup.
④ Control Buttons
Use to navigate through parameter menus and to change settings.
⑤ Battery Compartment
Requires two AA batteries or Shure SB900A rechargeable battery.
⑥ AA Battery Adapter
Use to secure AA batteries. Remove when using a Shure SB900A battery.
⑦ SMA Connector
Connection point for RF antenna.
⑧ Power Switch
Powers the unit on or off.
⑨ Power LED
• Green = unit is powered on
• Red = low battery, Mute Mode enabled, input overload, or battery error
(see Troubleshooting)
• Amber = power switch mode: locked with switch in off position
⑩ Input Jack
Connects to a 4-Pin Mini Connector (TA4F) microphone or instrument cable.
Note: A LEMO connector model variation of this transmitter is available.
1
7 8 9 10
2
3
4
5
6
Updating Firmware
Firmware is embedded software in each component that controls functional-
ity. Periodically, new versions of firmware are developed to incorporate addi-
tional features and enhancements. To take advantage of design improve-
ments, new versions of the firmware can be uploaded and installed using
the Shure Update Utility. The Shure Update Utility is available for download
from http://www.shure.com/.
Firmware Versioning
When performing an update, download firmware to the receiver first, and
then update transmitters to the same firmware version to ensure consistent
operation.
The firmware numbering for Shure devices uses the following format: MA-
JOR.MINOR.PATCH (e.g., 1.2.14). At a minimum, all devices on the network
(including transmitters), must have the same MAJOR and MINOR firmware
version numbers (e.g., 1.2.x).
Updating the Transmitter
1. To upload the firmware to the transmitter, go to Device Configuration>Tx
Firmware Update on the receiver.
2. Place the transmitter on its side and align the IR ports.
3. Press ENTER on the receiver to begin the download to the transmitter.
IR ports must be aligned for the entire download, which can take 50
seconds or longer.
Transmitter Controls
Use the controls to navigate through parameter menus and change values.
Shure IncorporatedAD1 AD1 Bodypack Transmitter
2017/08/032/12

exit enter
^
^
Acts as a 'back' button to return to previous menus or parameters
without confirming a value change
exit
Enters menu screens and confirms parameter changes
enter
Use to scroll through menu screens and to change parameter
values
∨∧
Tip: Use the following control shortcuts for quick set up:
• Hold the ∧ button while powering-on to lock or unlock the transmitter
controls
• Hold the exit button while powering-on to set the transmitter RF output
to mute
Locking the Controls
Lock transmitter controls to prevent accidental or unauthorized changes to
parameters. The lock icon is shown on the home screen when the control
lock in enabled.
1. From the Utilities menu, navigate to Lock and select one of the following:
⁃Locked: Locks the controls
⁃Unlocked: Unlocks the controls
2. Press enter to save.
Tip: To quickly unlock a transmitter: Press enter, select Unlocked, and press
enter.
Home Screen Display
The home screen shows transmitter information and status.
Tip: There are four options to choose the information shown on the home
screen. Use the arrow buttons to select one of the following choices:
• Name
• Frequency Setting
• Group (G) and Channel (C)
• Device ID
The following icons appear to indicate transmitter settings:
• Battery runtime in hours and minutes or bar display
• Key: Displayed when encryption is enabled
• Lock: Displayed when controls are locked
• STD: Standard Transmission Mode
• HD: High Density Transmission Mode
• Box: When the box has an "x", Mute Mode is on and engaged. If the box
is empty, Mute Mode is on, but not engaged.
Shure
470.200MHz
7:45
Battery Installation
AA
SB900A

① Accessing the Battery Compartment
Press the side tabs on the bodypack and open the battery door as shown to access the battery compartment.
Shure IncorporatedAD1 AD1 Bodypack Transmitter
3/122017/08/03

② Installing Batteries
•AA Batteries: Place batteries (note polarity markings) and AA Adaptor as shown and close the door
•Shure SB900A Battery: Place battery as shown (note polarity markings). Remove the AA adapter and set it aside. Close the door to secure the battery.
Note: If using AA batteries, set the battery type using the transmitter menu.
Setting the AA Battery Type
To ensure accurate display of transmitter runtime, set the battery type in the transmitter menu to match the installed AA battery type.
Note: If a Shure SB900A rechargeable battery is installed, selecting a battery type is not necessary and the battery type will display Shure.
1. Navigate to the Utilities and select Battery.
2. Use the ▼▲ buttons to select the installed battery type:
⁃Alkaline = Alkaline
⁃NiMH = Nickel Metal Hydride
⁃Lithium = Lithium Primary
3. Press enter to save.
Battery
Battery: Alkaline
Battery
Battery: NiMH
Battery
Battery: Lithium
AA Battery Installation
Fully insert the batteries as shown to ensure proper battery contact and to allow the door to latch securely.
Correct Incorrect
Shure SB900A Rechargeable Battery
Shure SB900A lithium-ion batteries offer a rechargeable option for powering
the transmitters. Batteries quickly charge to 50% capacity in one hour and
reach full charge within three hours.
Single chargers and multiple bay chargers are available to recharge the
Shure batteries.
Caution: Only charge Shure rechargeable batteries with a Shure battery
charger.
Shure SB900A Runtime
35 mW10 mW2 mW
Up to 5 hoursUp to 9 hoursUp to 9 hours
Checking Battery Info
When using an SB900A rechargeable battery, the receiver and transmitter
home screens display the number of hours and minutes remaining.
Detailed information for the battery is displayed Battery menu of the transmit-
ter: Utilities>Battery
•Battery: The chemistry type of for the installed battery (Shure, Alkaline,
Lithium, NiMH)
•Bars: Indicates the number of bars displayed
•Time: Battery runtime
•Charge: Percentage of charge capacity
•Health: Percentage of current battery health
•Cycle: Record of the number of charging cycles for the installed battery
•Temp: Battery temperature in Fahrenheit and Celsius
Battery Info
Time: 8:15
Health: 98%
Charge: 97%
Important Tips for Care and Storage of Shure
Rechargeable Batteries
Proper care and storage of Shure batteries results in reliable performance
and ensures a long lifetime.
• Always store batteries and transmitters at room temperature
Shure IncorporatedAD1 AD1 Bodypack Transmitter
2017/08/034/12

• Ideally, batteries should be charged to approximately 40% of capacity
for long-term storage
• Periodically clean the battery contacts with alcohol to maintain ideal
contact
• During storage, check batteries every 6 months and recharge to 40% of
capacity as needed
For additional rechargeable battery information, visit www.shure.com.
AA Batteries and Transmitter Runtime
Transmitters are compatible with the following AA battery types:
• Alkaline
• Nickel Metal Hydride (NiMH)
• Lithium Primary
A 5-segment battery indicator representing the charge level of the transmitter
battery is displayed on the screens of the transmitter and receiver. The fol-
lowing tables contain the approximate remaining transmitter runtime in
hours:minutes.
Note: Battery runtimes vary by manufacturer, battery age, and environmental
conditions.
AA Batteries and Transmitter Runtime
Alkaline
Approximate
Runtime
Remaining
(hours:minutes)
Battery Indicator
8:00 - 6:00
> 4:00
> 1:45
≦ 1:45
≦ 0:45
≦ 0:15
NiMH (2700 mAh)
Approximate Runtime
Remaining (hours:minutes)
Battery Indicator
11:00 - 8:00
> 5:00
> 2:00
≦ 2:00
≦ 0:45
≦ 0:15
Lithium Primary (3500 mAh)
Approximate Runtime
Remaining (hours:minutes)
Battery Indicator
14:00 - 10:00
> 6:00
> 2:00
≦ 2:00
≦ 0:45
≦ 0:15
Menu Parameters
The Main menu organizes the available transmitter parameters into three
sub-menus:
•Radio
•Audio
•Utilities
Tip: Use the arrow buttons to scroll between the sub-menus.
Main
Radio
Tips for Editing Menu Parameters
• To access the menu options from the home screen, press the enter but-
ton. Use the arrow buttons to access additional menus and parameters.
• A menu parameter will blink when editing is enabled
• To increase, decrease or change a parameter, use the arrow buttons
• To save a menu change, press enter
• To exit a menu without saving a change, press exit
Shure IncorporatedAD1 AD1 Bodypack Transmitter
5/122017/08/03

Menu Map
Radio
Group Channel
Frequency
RF Power
RF Output
Level
Audio
Oset
Pad
Polarity
MuteMode
Tone
Utilities
Dev ID
Lock
Marker
About
Battery
Reset All
Radio Menu
G: and C: Group and Channel
Press the enter button to enable editing of a group (G:) or channel (C:). Use
the arrow buttons to adjust the values.
Frequency
Press the enter button once to edit the first 3 digits, or twice to edit the second
3 digits.
RF Power
Higher power settings can extend the range of the transmitter.
RF Output
• On: RF signal is active
• Mute: RF signal is inactive
Audio Menu
Pad
Adjust the pad to avoid overloading the audio input. Select -12 dB or Off.
Offset
Adjust Offset level to balance mic levels when using two transmitters for fre-
quency diversity or when assigning multiple transmitters to receiver slots.
Adjustment range: -12 dB to +21 dB.
Polarity
Selectable polarity assignment for LEMO connector transmitters:
•Pos: Positive pressure on microphone diaphragm produces positive
voltage on pin 2 (with respect to pin 3 of XLR output) and the tip of the
TRS output.
•Neg: Positive pressure on microphone diaphragm produces negative
voltage on pin 2 (with respect to pin 3 of XLR output) and the tip of the
TRS output.
MuteMode
When enabled, the power switch is configured as a mute switch for the audio:
• Power switch on: audio signal on
• Power switch off: audio signal muted
Tone
Transmitter will generate a continuous test tone. The tone can be set to 400
Hz or 1000 Hz.
Level
When enabled, allows for adjustment of the output level of the test tone.
Utilities Menu
Dev ID
Assign a device ID of up to 9 letters or numbers.
Lock
Locks the transmitter controls and power switch.
Marker
When enabled, press the enter button to drop a marker in Wireless Work-
bench.
Battery
Displays battery information:
•Battery: The chemistry type of for the installed battery (Shure
Rechargeable, Alkaline, Lithium, NiMH)
•Bars: Indicates the number of bars displayed
•Time: Battery runtime
•Charge: Percentage of charge capacity
•Health: Percentage of current battery health
•Cycle: Record of the number of charging cycles for the installed battery
•Temp: Battery temperature in Fahrenheit and Celsius
About
Displays transmitter information:
•FW: Installed firmware
•HW: Hardware version
•SN: Serial number
Reset All
Restores all transmitter parameters to factory settings.
IR Sync
Use IR Sync to form an audio channel between the transmitter and receiver.
Note: The receiver band must match the band of the transmitter.
1. Select a receiver channel.
Shure IncorporatedAD1 AD1 Bodypack Transmitter
2017/08/036/12

2. Tune the channel to an available frequency using group scan or manually turn to an open frequency.
3. Power on the transmitter.
4. Press the SYNC button on the receiver.
5. Align the IR windows between the transmitter and the receiver so that the IR LED illuminates red. When complete, Sync Success! appears. The transmitter
and receiver are now tuned to the same frequency.
<15 cm (6 in.)
AD4Q
Axient Digital
Wireless Receiver
POWER
PUSH
CONTROL
NAVIGATE
IR RF
A B
OL
AUDIO
SYNC
4
RX 4RF
A B
OL
AUDIO
SYNC
3
RX 3RF
A B
OL
AUDIO
SYNC
2
RX 2RF
A B
OL
AUDIO
SYNC
1
RX 1
ULXD4
Digital Wireless Receiver
sync
Sync Success!
Note:
Any change to the encryption status on the receiver (enabling/disabling encryption) requires a sync to send the settings to the transmitter. New encryption keys
for the transmitter and receiver channel are generated on every IR sync, so to request a new key for a transmitter, perform an IR sync with the desired receiver
channel.
Setting the Frequency Manually
The transmitter can be manually tuned to a specific frequency, group, or
channel
1. Navigate to the Radio menu.
2. To manually select a frequency, scroll to G: and C: to edit the group and
channel, or to the frequency parameter .
3. Press enter to enable editing.
4. Use the ∧∨ buttons to adjust the group, channel, or frequency.
5. Press enter to save, and then press exit when finished.
RADIO
G: 1 C:1
470.700 MHz
RF Power: 10mW
Wearing the Bodypack Transmitter
Clip the transmitter to a belt or slide a guitar strap through the transmitter clip
as shown.
For best results, the belt should be pressed against the base of the clip.
Tip: The clip can removed and rotated 180 degrees to increase mounting
options.
RF Mute
RF Mute prevents transmission of the audio by suppressing the RF signal,
while allowing the transmitter to remain powered-on. The home screen dis-
plays RF Mute in this mode.
Shure IncorporatedAD1 AD1 Bodypack Transmitter
7/122017/08/03

RADIO
RF Output: Mute
1. From the Radio menu, navigate to RF Output.
2. Choose one of the following options:
⁃On: RF signal is active
⁃Mute: RF signal is disabled
3. Press enter to save.
Turning the transmitter off and on, or replacing the battery will restore RF
Output to On.
Power-on RF Mute
Power-on RF Mute places the transmitter in RF Mute mode immediately
when turned on.
• Starting with the transmitter off, press and hold the exit button, and then
switch on the power
• Continue to hold the exit button until the RF Muted message appears on
the home screen
Input Overload
The OVERLOAD message is displayed when the audio input experiences a
high-level signal. The power LED will turn red as an additional indicator of
an overload. Reduce the input signal or enable the input pad to remove the
overload.
Shure
OVERLOAD
7:45
Matching Audio Levels with Offset
When linking two or more transmitters to a receiver, there may be a difference
in volume levels between microphones or instruments. If this occurs, use the
Offset function to match the audio levels and eliminate audible volume differ-
ences between transmitters. If using a single transmitter, set Offset to 0 dB.
1. Turn on the first transmitter and perform a sound check to test the audio
level. Turn off the transmitter when finished.
2. Turn on the second transmitter and perform a sound check to test the
audio level. Repeat for any additional transmitters.
3. If there is an audible difference in the sound level between the transmit-
ters, navigate to the Offset menu (Audio>Offset) in the transmitter to in-
crease or decrease the Offset in realtime to match the audio levels.
Audio
Offset: +1dB
Tone Generator
The transmitter contains an internal tone generator that produces a continuous
audio signal. The tone is helpful when conducting a sound check or for trou-
bleshooting the audio signal chain. The level of the tone is adjustable from
-60 dB to 0 dB and the frequency can be set to 400 Hz or 1000 Hz.
1. From the Audio menu select Tone.
2. Set the frequency to 400 Hz or 1000 Hz.
3. Select Level and use the arrow buttons adjust the value between -60 dB
and 0 dB.
Tip: Always start with the level set to -60 dB to avoid overloading speakers
or headphones.
Turn off the tone by selecting Off from the menu or by cycling the transmitter
power.
AUDIO
Mute Mode: Off
Tone: 400Hz
Level: -60db
Specifications
Mic Offset Range
-12 to 21 dB (in 1 dB steps)
Shure IncorporatedAD1 AD1 Bodypack Transmitter
2017/08/038/12

Battery Type
Shure SB900A Rechargeable Li-Ion or LR6 AA batteries 1.5 V
Battery Runtime
@ 10 mW
up to 9 hoursShure SB900A
up to 8 hoursalkaline
0
Dimensions
86 mm x 66 mm x 23 mm (3.4 in. x 2.6 in. x 0.9 in.) H x W x D
Weight
155 g (5.0 oz.), without batteries
Housing
Cast Metal
Audio Input
Connector
4-Pin male mini connector (TA4M) or Lemo Connector
Configuration
Unbalanced
Impedance
1 MΩ,
Maximum Input Level
1 kHz at 1% THD
8.5 dBV (7.5 Vpp)Pad Off
20.5 dBV (30 Vpp)Pad On
Preamplifier Equivalent Input Noise (EIN)
System Gain Setting ≥ +20
-120 dBV, A-weighted, typical
RF Output
Connector
SMA
Antenna Type
1/4 wave
Impedance
50 Ω
Occupied Bandwidth
<200 kHz
Modulation Type
Shure Axient Digital Proprietary
0See Battery Runtime Chart
Shure IncorporatedAD1 AD1 Bodypack Transmitter
9/122017/08/03

Power
2 mW, 10 mW, 35 mW
1
Frequency Bands and Transmitter RF Power
RF Power (mW)***Frequency Range (MHz)Band
2/10/35470 to 510G53
2/10/20
479 to 565
G54
2/10/35
470 to 636*
G55
2/10/35
470 to 636
G56
2/10/35
470 to 616*
G57
2/10/35
510 to 530
G62
2/10/35
520 to 636
H54
2/10/35
606 to 698*
K53
2/10/35
606 to 663**
K54
2/10/35
606 to 694
K55
2/10/35
606 to 714
K56
2/10/35
606 to 790
K57
2/10/35
622 to 698
K58
2/10/35
630 to 787
L54
2/10/35
794 to 806
R52
2/10
806 to 810
JB
2/10
925 to 937.5
X51
2/10/35
941 to 960
X55
Note: *with a gap between 608 to 614 MHz.
Note: **with a gap between 608 to 614 MHz and a gap between 616 to 653 MHz.
Note: ***power delivered to the antenna port.
Frequency Range
Gamme de frequences
Gamme di frequenza
Gama de frequencias
Frequenzbereich
Country Code
Code de Pays
Codice di paese
Código de país
Länder-Kürzel
*A, B, BG, CH, CY, CZ, D, DK, EST, F
*FIN, GB, GR, H, HR, I, IRL, IS, L, LT
*M, N, NL, P, PL, RO, S, SK, SLO, TR
*all other countries
* This equipment may be capable of operating on some frequencies not authorized in your region. See Licensing Information.
1See Frequency Range and Output Power table, varies by region
Shure IncorporatedAD1 AD1 Bodypack Transmitter
2017/08/0310/12