Shuttle Spacewalker AV32 User manual

AV32
FC-PGA/PPGA Celeron
and FC-PGA Pentium III Processor
Based DDR/SDR Main Board
User's Manual

Shuttle®SpacewalkerTM AV32
PPGA/FC-PGA Celeron and FC-PGA Pentium III processor
based AGPset Mainboard
Manual Version 1.1
Copyright
Copyright©2001 by Shuttle®Inc. All Rights Reserved.
No part of this publication may be reproduced, transcribed, stored in a retrieval system,
translated into any language, or transmitted in any form or by any means, electronic,
mechanical, magnetic, optical, chemical, photocopying, manual, or otherwise, without
prior written permission from Shuttle®Inc.
Disclaimer
Shuttle®Inc. shall not be liable for any incidental or consequential damages resulting from the
performance or use of this product.
This company makes no representations or warranties regarding the contents of this manual.
Information in this manual has been carefully checked for reliability; however, no guarantee is
given as to the correctness of the contents. In the interest of continued product improvement,
this company reserves the right to revise the manual or include changes in the specifications
of the product described within it at any time without notice and without obligation to notify any
person of such revision or changes. The information contained in this manual is provided for
general use by the customers.
Trademarks
Spacewalker is a registered trademark of Shuttle Inc.
VIA is a registered trademark of VIA Corporation.
Intel, Pentium is a registered trademarks of Intel Corporation.
PS/2 is a registered trademark of IBM Corporation.
AWARD is a registered trademark of Award Software Inc.
Microsoft and Windows are registered trademarks of Microsoft Corporation.
General Notice: Other brand and product names used herein are for identification
purposes only and may be trademarks of their respective owners.
M411

- 1 -
WHAT’S IN THE MANUAL .....................................................................5
Quick Reference................................................................................................5
About This Manual ............................................................................................5
1 INTRODUCTION .................................................................................6
1.1 TO DIFFERENT USERS ..............................................................................6
First-TimeDIYSystemBuilder ..................................................................6
ExperiencedDIYUser ..............................................................................6
SystemIntegrator .....................................................................................6
1.2 ITEM CHECKLIST........................................................................................7
2 FEATURES..........................................................................................8
2.1 SPECIFICATIONS ........................................................................................8
3 HARDWARE INSTALLATION ...........................................................11
3.1 STEP-BY-STEP INSTALLATION ............................................................... 11
STEP1InstalltheCPU...........................................................................12
STEP 2 Set Jumpers..............................................................................13
STEP3InstallSDRAMSystemMemory .................................................13
STEP4InstallInternalPeripherals in SystemCase.................................14
STEP5MounttheMainboardontheComputerChassis ........................15
STEP6ConnectFront-panelSwitches/LEDs/Speaker/Audio/USB ........16
STEP 7 Connect IDE & Floppy Disk Drives............................................18
STEP8ConnectOther Internal Peripherals ............................................19
STEP9ConnectPowerSupply..............................................................19
STEP10InstallAdd-onCardsinExpansionSlots ..................................20
STEP11ConnectExternalPeripheralstoBack-panel............................21
STEP 12 First Time System Boot Up......................................................23
STEP13InstallDriver&SoftwareComponents......................................24
TABLE OF CONTENTS

- 2 -
3.2 JUMPER SETTINGS ..................................................................................25
JUMPER&CONNECTORGUIDE .........................................................26
Jumpers
USBWake-up Setting (JP6/JP7)............................................................29
FSB Speed Auto Configuration Setting (J1) ...........................................30
BIOSWriteProtection(J9) .....................................................................31
Clear CMOS (JP1).................................................................................31
Back-Panel Connectors
PS/2 Keyboard & PS/2 Mouse Connectors ............................................32
USB1/USB2PortConnectors.................................................................32
COM1/2Connector ................................................................................32
ParallelPortConnector...........................................................................32
Line-Out .................................................................................................33
Line-In ....................................................................................................33
Mic-In .....................................................................................................33
MIDI/GAMEPort.....................................................................................33
Front-Panel Connectors
ATXPowerOn/Off SwitchConnector(PWR_ON) ...................................34
EPMIConnector(EPMI) .........................................................................34
Green LED Connector (G LED) ..............................................................35
HDD LED Connector (HDD LED)...........................................................35
PWR LED Connector (PWR_ LED)........................................................35
HardwareResetConnector(RST) ..........................................................36
Speaker Connector (SPK)......................................................................36
Line-OutandMic-InHeader(J8) .............................................................36
ExtendedfourUSBConnectorHeader(JUSB1/JUSB2).........................37

- 3 -
Internal Peripherals Connectors
EnhancedIDEPortsandFloppyConnectors ..........................................38
Other Connectors
ATX Power Supply Connector (J7)..........................................................39
CoolingFAN ConnectorsforCPUFANs(FAN1/FAN2),
& Chassis (FAN3) ..................................................................................39
SIR/CIRConnector(J2) ..........................................................................40
Wake-On-LANConnector (WOL1)..........................................................40
AudioConnectorTAD_In(JP3)(Green)..................................................41
AudioConnectorAUX_In(JP4)(White) ..................................................41
AudioConnectorCD_In(JP5)(Black) ....................................................41
3.3 SYSTEM MEMORY CONFIGURATION ......................................................42
InstallMemory.........................................................................................42
UpgradeMemory ...................................................................................42
4 SOFTWARE UTILITY .......................................................................43
4.1 Mainboard CD Overview ..........................................................................43
4.2 Install VIA 4 in 1 Driver .............................................................................44
4.3 Install Audio Device Software..................................................................45
4.4 View the User's Manual............................................................................46

- 4 -
5 BIOS SETUP.....................................................................................47
5.1 ENTER THE BIOS......................................................................................47
5.2 THE MAIN MENU .......................................................................................48
STANDARD CMOS FEATURES ................................................................50
ADVANCED BIOS FEATURES..................................................................54
ADVANCED CHIPSET FEATURES...........................................................58
INTEGRATEDPERIPHERALS...................................................................62
POWERMANAGEMENTSETUP ..............................................................67
PNP/PCICONFIGURATION .......................................................................72
PC HEALTH STATUS.................................................................................74
FREQUENCY/VOLTAGECONTROL..........................................................76
LOAD FAIL-SAFE DEFAULTS...................................................................77
LOADOPTIMIZEDDEFAULTS ..................................................................77
SET SUPERVISOR PASSWORD ..............................................................78
SET USER PASSWORD ...........................................................................78
SAVE & EXIT SETUP.................................................................................79
EXITWITHOUTSAVING.............................................................................79

- 5 -
Quick Reference
Hardware Installation >> Step-by-Step ................................................ Page 11
Jumper Settings >> A Closer Look ...................................................... Page 25
Software Utility >> How to Install ......................................................... Page 43
BIOS Setup >> How to Configure ........................................................ Page 47
About This Manual
For First-Time DIY System Builder......................................................... Page 6
For Experienced DIY User ...................................................................... Page 6
For System Integrator ............................................................................. Page 6
WHAT’S IN THE MANUAL

- 6 -
1INTRODUCTION
1.1 To Different Users
First-Time DIY System Builder
Welcome to the DIY world! Building your own computer system is not as
difficult as you may think. To make your first computer DIY experience
successful, right from the start, we ha e designed the Chapter 3 Hardware
Installation section in a step-by-step fashion for all the first-time DIY system
builders. Prior to installation, we also suggest you to read the whole manual
carefully to gain a complete understanding of your new Shuttle AV32
mainboard.
Experienced DIY User
Congratulate on your purchase of the Shuttle AV32 mainboard. You will find
that installing your new Shuttle AV32 mainboard is just easy. Bundled with an
array of onboard functions, the highly-integrated AV32 mainboard pro ides
you with a total solution to build the most stable and reliable system. Refer to
sections 3.2 Jumper Settings and Chapter 4 Software Utility to find out how to
get the best out of your new mainboard. Chapter 5 BI S Setup also contains
the rele ant information on how to tune up your system to achie e higher per-
formance.
System Integrator
You ha e wisely chosen Shuttle AV32 to construct your system. Shuttle AV32
incorporates all the state-of-the-art technology of the Apollo Pro266 chipset
from VIA. It integrates the most ad anced functions you can find to date in a
compact ATX board. Refer to sections 3.2 Jumper Settings and Chapter 4
Software Utility for an in-depth iew of system construction.

- 7 -
1.2 Item Checklist
Check all items with your AV32 mainboard to make sure nothing is missing.
The complete package should include:
!One piece of Shuttle AV32 Mainboard
!One piece of ATA100/66/33 Ribbon Cable
!One piece of Floppy Ribbon Cable
!One piece of twin ports USB Cable(optional)
!AV32 User’s Manual
!One piece of Bundled CD-ROM with containing:
"AV32 user’s manual on PDF format
"VIA4-IN-1driver
"VIA Audio driver
"AwardFlashingUtility
KBMS1 USB1 COM1PRINT
COM2
AUDIO
CD_IN
AUX_IN
TAD_IN
USB3 &4 USB5&6
FDDHDD
IR
CA37511D 0037 9248AF-151ICS
Panasoni c
CR2032
3V
JAPAN1
M
C
VT8233
003
9
C
DTAIWAN
13C001005
ACR1
PCI1 PCI2 PCI3 PCI4 PCI5
JP3
JP4
JP5
AGP1
J1
J7
FAN1
JUSB1
JP7
JP6
JUSB2
J2
J9
J5
1
1
11
1
1
RST
PWR_LED + - SPKJ8
1
1
1
1
1
1
11
JP1
FAN3
FAN2
DIMM1DIM2 DIMM2DIM1
FDD1 IDE2
IDE1
GLED +-
+- EPMI P WR_ONHDD LED
1
1
1
1
1-2 3-4 5-6 7-8
PGA370
A
W
AR
D
P
C
I
/
PNP
686
169332966
1998
C
WOL1
1
i nbond

- 8 -
AV32 mainboard is carefully designed for the demanding PC user who wants high perfor-
mance and maximum intelligent features in a compact package.
2.1 Specifications
!!
!!
!CPU Support
Support Socket370 package CPU with 66/100/133 MHz FSB.
Intel PPGA/FC-PGA Celeron processors: 300 ~ 800+ MHz.
IntelPentiumIII FC-PGAprocessors:500MHz~1.13+GHz.
VIACyrixIIIprocessors.
!!
!!
!Chipset
Features VIA Apollo Pro266, VT8633/VT8233 Chipset.
VT8633, Integrated high performance SDRAM and DDR DRAM controller.
!!
!!
!Jumperless CPU Configuration
Soft-configurationFSB(TheFSBspeedissoftwareconfigurablefrom 66MHz
to 166MHz by 1MHz step in the Frequency/Voltage Control of BIOS setup
program.)
!!
!!
!AC'97 Link for Audio and Telephony CODEC
AC'97 2.1 compliant
Spread independent PCI functions for Audio and Modem
!!
!!
!Versatile Memory Support
Two 184-pin DIMM slots to support up to 2GB of PC1600 or PC2100
compliantDDR SDRAM.
or two 168-pin DIMM slots to support up to 2GB of PC100 or PC133
compliantSDR SDRAM.
!!
!!
!PCI Expansion Slots
Providesfive32-bitPCIslots.
!!
!!
!ACR Expansion Slot
Provides one ACR (Advanced Communication Riser) slot.
!!
!!
!AGP Expansion Slot
Provides one 32-bit AGP slot which supports up to 4X AGP device.
2FEATURES

- 9 -
!!
!!
!I/O Interface
ProvidesavarietyofI/Ointerfaces:
"1 × Floppy interface for 3.5-inch FDD with 720KB, 1.44MB, or 2.88MB
formatorfor5.25-inchFDD with 360K or 1.2MB format.
"1 × PS/2 mouse connector.
"1 × PS/2 Keyboard connector.
"2 × DB9 Serial connectors 16550 UART compatible.
"1 × Infrared communication port .
(Serial port COM2 can also be redirected to an external IrDA Adapter
forwirelessconnection.)
"1 × DB25 Parallel port supporting Standard Parallel Port (SPP),
Enhanced Parallel Port (EPP), and Extended Capabilities Port (ECP)
datatransmissionschemes.
"1×Line-Outport.
"1×Line-Inport.
"1×Mic-Inport.
"1×MIDI/GAMEport.
!!
!!
!6 USB Supported Onboard
"2 × USB connectors on back-panel and two 10-pin header for optional
USB cable to extend another 4 USB ports .
!!
!!
!PCI Bus Master IDE Controller Onboard
TwoUltraDMA 100/66/33 BusMasterDual-channelIDE portsprovidesupport
to a maximum of four IDE devices (one Master and one Slave per channel).
The IDE Bus implements the data transfer speed up to 100/66/33MB/sec and
also supports Enhanced PIO Modes 0~4.
80-pin Cable Backward Compatible Legacy ATAPI Devices, ATAPI IDE CD-
ROM, CD-R, CD-RW, and LS-120 Supports.
!!
!!
!ATX Power Supply Connector
ATX power supply unit can be connect to the onboard 20-pin ATX power
connector,supportingSuspend and Soft-On/Off by dual-function power
button.
!!
!!
!Advanced Configuration and Power Interface
Features four power saving modes: Snoop, Suspend to RAM, Suspend to
Disk,andSoft-Off.ACPIprovidesmoreefficientEnergySavingsFeatures
controlled by your operating system that supports OS Direct Power Manage-
ment(OSPM)functionality.

- 10 -
!!
!!
!System BIOS
Provides licensed Award BIOS V6.0 PG on 2Mb Flash EEPROM and
supportsGreenPC,DesktopManagementInterface(DMI).
!!
!!
!ATX Form Factor
System board conforms to the ATX specification.
Board dimension: 305mm × 245mm.
!!
!!
!Advanced Features
"Dual Function Power Button - The system can be in one of two states;
one is Suspend mode and the other is Soft-Off mode. Pushing the power
button for less than 4 seconds places the system into Suspend mode.
When the power button is pressed for longer than 4 seconds, the system
enterstheSoft-Offmode.
"Wake-on-LAN (WOL) - The onboard WOL connector can be attached to
a network card that supports this function to wake up the system via LAN.
"Modem Ring Power-On - The system can be powered on automatically
by the activation of modem ring.
"CPU Clock Setting-Thisitemallows userstoadjustCPUHostClockin BIOS.
"CPU Vcore Setting- This item allows users to adjust CPU Vcore in BIOS.
!!
!!
!Intelligent Features
"Voltage Monitoring - Monitorsvarious voltages of key elements, such as
theCPU, and other critical systemvoltage levels to ensure stablecurrent
passing through mainboard components. System voltages include Vcore
on CPU, and +5V, +12V, -5V, -12V on system etc.
"Fan Status Monitoring - To prevent CPU from overheating, the CPU fan is
monitored for RPM and failure. (CPU Cooling FAN with RPM sensor is
required.)
"Temperature Monitoring -Thisitemallowsuserstomakesurewhether
the CPU or system runs in a suitable temperature.

- 11 -
3HARDWAREINSTALLATION
Before removing or installing any of these devices including CPU, DIMMs, Add- n
Cards, Cables, please make sure to unplug the onboard power connector.
This section outlines how to install and configure your AV32 mainboard. Refer to the
following mainboard layout to help you identify arious jumpers, connectors, slots, and
ports. Then follow these steps to guide you through a quick and correct installation of
your system.
3.1 Step-by-Step Installation
Accessories Of AV32
KBMS1
USB1
COM1 PRINT
COM2
AUDIO
CD_IN
AUX_IN
TAD_IN
USB3&4 USB5&6
FDD HDD
IR
CA37511D
0037
9248A F-1 51
1+5
Panasonic
CR2032
3V
JAPAN1
M
C
VT8233
00 39C D TA IW AN
13 C00 1005
AC R1
PC I1
PC I2
PC I3
PC I4
PC I5
JP3
JP4
JP5
AG P1
J1
J7
FAN1
JUSB 1
JP7
JP6
JUSB 2
J2
J9
J5
1
1
11
1
1
RST
PW R _LE D
+ - SPK J8
1
1
1
1
1
1
11
JP1
FAN3
FAN2
DIMM1DIM2 DIMM2DIM1
FDD 1 IDE 2
IDE 1
GLED
+ -
+ -
EPM I PW R _ONHDD
LED
1
1
1
1
1-2
3-4
5-6
7-8
2/)!%
)9)4,
PC I/PNP 68 6
169 332 966
199 8
C
WOL1
1
inbond
RichTek
R T9231
CS2EV1
PS/2 Keyboard/Mouse
Connectors
USB Wake-up - JP 6
ATX Power Connector
Parallel Connector
Ser al Port
Connector (COM1)
Ser al Port
Connector (COM2)
L ne-In/L ne-Out/M c-In
Game/MIDI Connectors
System Clock - J1
Floppy Connector
BIOS Wr te Protect on - J9
Front Panel Connector - J5
Two E-IDE Connectors
FAN3
FAN1
Socket 370 FAN2
F ve PCI Slots
One ACR Slot
One 4 x AGP Slot
VIA VT8633 Ch pset
USB Connectors
L-OUT & MIC-IN Connectors header - J8
IR Connector - J2 Clear CMOS - JP 1
I/O Controller
CD Aud o Connectors
Onboard CODEC
Wake-On-LAN Connector - WOL1
Programmable
2Mb Flash EEPROM
Extended four USB Connectors
header - JUSB1/2
Two 168-p n SDRAM DIMM Slots
Two 184-p n DDR DIMM Slots
USB Wake-up - JP7

- 12 -
Step 1
Install the CPU:
1. Locate the CPU ZIF (Zero Insertion Force) socket on the upper-right
sector of your mainboard (between the back-panel connectors and the
DIMM memory slots).
2. Pull the CPU ZIF socket le er slightly sideways away from the socket
to unlock the le er, and then bring it to an upwardly ertical position.
3. Place your PPGA/FC-PGA370 processor in the ZIF socket. Note that the
CPUs edges ha e been purposely designed non-symmetrically to pre ent
from inserting the processor in the wrong direction. The following diagram
demonstrates the correct placement of the CPU in the ZIF socket. You can
see that the two blunt-edged corners should face towards the socket-le er.
4. Slightly push the PPGA/FC-PGA370 processor into the socket without
applying excessi e force while making sure there is no gap between CPU
and socket. Then lower the socket-le er all the way down to its horizontal
position and lock it to secure the CPU in place.
5. The PPGA/FC-PGA370 processor requires a set of heatsink/fan to ensure
proper cooling of the processor. If heatsink/fan ha e not been already
mounted on your CPU, you must purchase the heatsink/fan separately
and ha e it installed. Plug the cable throught the heatsink/fan in the CPU
fan power connector located nearby. Note that there are se eral types of
CPU fan connectors. Normally, if your mainboard supports the hardware
monitoring function, a 3-pin fan power connector should allow your system
to detect the CPU fans speed . The CPU fan can also run with a 2-pin fan
power connector, howe er, detection of CPU fans speed is not supported.
Another type of CPU fan may feature a large 4-pin fan power connector,
which does not support CPU fan's speed detection and must be directly
connected to the systems power supply unit. Please refer to the following
diagram.
2/) !% 2/) !%
Lever BlankBlank Notch Notch
PPGA CPU
2/) !%
Pen tium MAL AY
RB80526P Y 550256
Q944A036-0393 S L3R3
®
FC-PGA CPU

- 13 -
Step 2.
Set Jumpers
This mainboard is jumperless! The default jumper settings ha e been set for
the common usage standard of this mainboard. Therefore, you do not need
to reset the jumpers unless you require special adjustments as in any of the
following cases:
1. O er-clock your CPU
2. Clear CMOS
For first-time DIY system builders, we recommend that you do not change the
default jumper settings if you are not totally familiar with mainboard configu-
ration procedures. The factory-set default settings are tuned for optimum
system performance. For the ad anced users who wish to customize their
system, section 3.2 Jumper Settings will pro ide detailed information on how
to configure your mainboard manually.
Step 3.
Install DDR or SDR SDRAM System Memory
To insert memory module(s) in any one or two DIMM slot(s). Please note
that modules are directional and will not go in the DIMM slots unless prop-
erly oriented. After the module is fully inserted into the DIMM slots, lift the
clips of both sides of the DIMM slot to lock the module in place.
SDR SDRAM DDR SDRAM

- 14 -
Step 4
Install Internal Peripherals in System Case
Before you install and connect the mainboard into your system case, we
recommend that you first assemble all the internal peripheral de ices into the
computer housing, including but not limited to the hard disk dri e (IDE
/HDD), floppy disk dri e (FDD), CD-ROM dri e, and ATX power supply unit.
This will greatly facilitate in making the connections to the mainboard de-
scribed below.
To install IDE & FDD dri es, follow this procedure:
1. Set the required jumpers on board each de ice according to the
instructions pro ided by the manufacturer. (IDE de ices, HDD, and
CD-ROM ha e to set jumpers on Master or Sla e mode depending
on your willing to install more than one de ice for each kind.)
2. Connect IDE cable and FDD cable on the back-panel of the internal
peripheral de ices to the corresponding headers on board. Note that the
cable should be oriented with its colored stripe (usually in red or magenta)
connected to pin#1 both on the mainboard IDE or FDD connector and on
the de ice as well.
3. Connect an a ailable power cable through your system power supply unit
to the back-panel of each peripheral de ice. Note that the power cable
is directional and cannot fit in if it is not properly positioned.

- 15 -
Step 5
Mount the Mainboard on the Computer Chassis
1. You may find that there are a lot of different mounting hole positions
both on your computer chassis and on the mainboard. To choose a
correct mounting hole, the key point is to keep the back-panel of the
mainboard in a close fit with your system case, as shown below.
2. After deciding on the proper mounting holes, position the studs between
the frame of chassis and the mainboard. The studs are used to fix the
mainboard and to keep a certain distance between the system chassis
and the mainboard, in order to a oid any electrical shortage between the
board and the metal frame of chassis. (If your computer case is already
equipped with mounting studs, you will need to tighten screws to attach
the mainboard.)
Note: In most computer housings, you will be able to find 4 or more
attachment points to install mounting studs and fix the mainboard.
If there arent enough matching holes, then make sure to install at
least 4 mounting studs to ensure proper attachment of the
mainboard.

- 16 -
Step 6
Connect Front-Panel Switches/LEDs/Speaker/Audio/USB
connectors
You can find there are se eral different cables already existing in the system
case and originating from the computers front-panel de ices (HDD LED,
Power LED, Reset Switch, PC Speaker, or USB de ices etc.) These cables
ser e to connect the front-panel switches, LEDs, USB, Line-Out, and Mic-In
connectors to the mainboards front-panel connectors group (J5, J8, JUSB1,
and JUSB2), as shown below.
1. ATX Soft Power On/Off (PWR_ON)
2. EPMI
(Hardware System Management
Interface)
J5
1RST
PWR_LED
+ - SPK
GLED
+ -
+ -
EPMI PWR_ONHDD
LED
J5
1RST
PWR_LED
+ - SPK
GLED
+ -
+ -
EPMI PWR_ONHDD
LED
USB3&4 USB5&6
JUSB1 JUSB2 J8
1
J5
1RST
PWR_LED
+ - SPK
GLED
+ -
+ -
EPMI PWR_ONHDD
LED

- 17 -
3. Green_LED (GLED)
4. HDD_LED (HDD LED)
5. Power-LED (PWR_LED)
6. Hardware Reset Switch (RST)
7. PC Speaker (SPK)
J5
1RST
PWR_LED
+ - SPK
GLED
+ -
+ -
EPMI PWR_ONHDD
LED
J5
1RST
PWR_LED
+ - SPK
GLED
+ -
+ -
EPMI PWR_ONHDD
LED
J5
1RST
PWR_LED
+ - SPK
GLED
+ -
+ -
EPMI PWR_ONHDD
LED
J5
1RST
PWR_LED
+ - SPK
GLED
+ -
+ -
EPMI PWR_ONHDD
LED
J5
1RST
PWR_LED
+ - SPK
GLED
+ -
+ -
EPMI PWR_ONHDD
LED

- 18 -
8. Line-Out and Mic-In header
9. Extended four USB connectors header
Step 7
Connect IDE & Floppy Disk Drives
1. IDE cable connector
2. FDD cable connector
GROUND GROUND USBD3+ USBD3- +5V
+5V
USBD2-
USBD2+
GROUND GROUND
USB3(USB5)
USB4(USB6)
JUSB1(JUSB2) 1
ELOUT
EROUT
AGND
EMIC_VCC
EMIC_IN
1
HDD
11
IDE2 IDE1
FDD
1
FDD1