SI Solo/Pro 2 User manual

Solo / Pro 2
Installation Instructions
24v DC Motors

Thank you for purchasing an SI product. If you have
any questions or need any assistance with your
Solo Pro, we would love to help you.
Technical Support: 512.832.6939
Hours of Support: 7:30am - 5pm CST
screeninnovations.com
[email protected]
Solo Pro 2Solo 2
Please use these QR Codes to access the updated
installation instructions and video tutorials.

CONTENTS
Initial Consideration ................................................... 1
Parts in the Box - 24v DC RTS .................................. 2
Parts in the Box - 24v DC 485 ....................................3
Spacer Blocks and Leveling Shims ........................ 4
Pre-wire 24v DC RTS .................................................. 5
Pre-wire 24v DC 485 ................................................... 6
Power Wire distance chart ........................................ 7
Installation .................................................................... 8 - 16
24v DC RTS
Running ........................................................................17
Programming ..............................................................18 - 19
Pairing another RF Remote ......................................20
24v DC 485
Programming with SIFI .............................................21 - 24
Programming with Limit Setting Tool.....................25 - 27
Programming with USB Programming cable........28- 29
Control with 3rd Party - (Wet Contact) - Fontus...30 - 31
Control with 3rd Party - (Dry Contact) - Fontus 32 - 33

CONTENTS
Control with 3rd Party - (IR) - Fontus ........................... 34 - 35
Control with 3rd Party - (IR) - Fontus
-programming ................................................................. 36 - 37
Control with 3rd Party - Fontus Keypad Application 38 - 39
Control with 3rd Party - Fontus Keypad and
Contact Closure Application.......................................... 40 - 41
Control with 3rd Party - via Serial.................................. 42
Control with 3rd Party - via SIFI..................................... 43 - 44
Control with 3rd Party - via DCT with 12v & IR............45
Mounting Accessories ..................................................... 46
Motor Accessories 24v DC RTS ..................................... 47
Motor Accessories 24v DC 485...................................... 48
Storage and Transport ...................................................... 49 - 50
Care and Maintenance .......................................................51
Troubleshooting ................................................................. 52 - 55
Warranty .............................................................................. 56 - 57

1
INITIAL CONSIDERATIONS
Thank you for your purchase of Solo/Pro 2. The
screen is mountable outdoors, but is not waterproof.
It has not been designed to be run or left in the rain or
condensing humidity. Also avoid water spray, splash
and extreme heat or cold. Protect your Solo/Pro 2 and
you can expect years of quality use.
For a quick install it is recommended you run
appropriate wire to the installation location before
installing the screen. See the Pre-Wire sections for
your particular control method for details.
The Short Throw material is not 100% opaque.
Light sources behind the screen may be visible in
the viewing surface.
Initial Considerations

2
24v DC RTS
PWR Solo/Pro 2 screen
RF Remote
24v DC Power
Supply
Parts in the box
24v DC RTS - Parts in the Box
(2) Ceiling/Wall
Locking brackets
Terminal block
receptacle and bracket
(6) Wood
fasteners
(6) Leveling Shims

3
(6) Wood
fasteners
24v DC Power
Supply
24v DC 485
Additional accessories required for 485 control (pg 38)
Parts in the box
Solo/Pro 2 screen
485
PWR
24v DC 485 - Parts in the Box
(2) Ceiling/Wall
Locking brackets USB Programming Kit
Terminal block
receptacle and bracket
(6) Leveling
Shims

4
Spacer Blocks & Leveling Shims
SPACER BLOCKS & LEVELING
SHIMS
Spacer Blocks are used
to clear an obstruction on
the wall. Connect spacer
block to each wall bracket
before installation.
Leveling Shims are used
if the ceiling or other
mounting surface is out
of level or plumb. Connect
to ceiling brackets before
installation.

5
PRE-WIRE - 24v DC RTS
1. Run 2 conductor wires to the left side of screen
cassette installation location (refer to pg. 11). Follow
the power wire distance chart (refer to pg. 7) to
ensure use of the correct wire gauge.
2. Terminate the wires with the provided terminal block
as shown below.
+ 24 VDC
- 24 VDC
V+
V-
+
-
G
Not
used
Pre-Wire - 24v DC RTS

6
+ 24 VDC
- 24 VDC
Data +
Data -
Data ground
V+
V-
+
-
G
PRE-WIRE - 24v DC 485
1. Run minimum 5 conductor wire to the left side of
screen cassette installation location (refer to pg. 11).
To be sure you have the correct wire, order directly
from SI (Part # - Non-Plenum - 800269/ 9020126
and Plenum rated - 9020127). If you are using third
party wire, follow the power wire distance chart
(refer to pg. 7) to ensure use of the correct wire
gauge for the 24 VDC wires.
2. Terminate the wires with the provided terminal
blocks shown below.
Pre-Wire - 24v DC 485

7
Do not use any combination above the line.
over 100
100
90
80
70
60
50
45
40
35
30
25
20
15
10
5
Distance
(ft.) 12 14 16 18 20 22 24
Standard Cu Wire Guage (min.)
POWER WIRE DISTANCE CHART
Power Wire Distance Chart

8
Proper mounting preparation will ensure a great
installation. Mounting brackets must be level to each
other, as well as plumb. They must be screwed into
structural members of some kind, such as ceiling joists
or wall studs. You may use the wood screws provided,
or other anchors (not provided) capable of carrying the
load, that are suitable to the substrate.
DO NOT MOUNT TO HOLLOW SHEET ROCK.
1. The drop is adjustable in the field between 0'' and
the MAX DROP (12'', 24'', or 36'', 2'' for short throw)
ordered for your screen. Use the drawing (refer to
pg. 9) to pick a bracket height that will allow you to
extend your screen to achieve the desired vertical
position of your viewing area.
INSTALLATION
Solo/Pro 2 - Installation

9
Solo/Pro 2 - Installation
13
4"
View Height
Drop
3.43”
(87mm)
2.02”
(51mm)
4.88”
(124mm)
3.43”
(87mm)
2.01”
(51mm)
3.78”
(96mm)
2.87”
(73mm)
2.85”
(72mm)
1.61”
(41mm)
Bracket
size
Small Medium Large

10
2. Determine the desired horizontal viewing position
centerline of the projected viewing area.
3. The Solo/Pro 2 screen must be installed with the
brackets no more than 4 inches from each end of
the cassette. Measure the overall length of the
cassette to determine the min and max horizontal
spacing of the mounts. Mark the location of the
brackets over a stud or ceiling joist and within an
appropriate distance from the ends. If the location
of the stud or ceiling joist does not allow the center
of the screen to match the projector lens' center,
another board or plate will have to be installed on
the wall or ceiling to take the mount fasteners.
Solo/Pro 2 - Installation

11
Solo/Pro 2 - Installation
wire
exits back
corner
of the
cassette
Cassette Length
View Width
Brackets secured to Wall or
Ceiling Structural Supports
Screen Centerline Structural Supports
1" Min to 4" Max
pull wire
through the
hole in gray
zone

12
4. Secure the brackets to the wall or ceiling structural
supports using appropriate fasteners. Make sure the
brackets are along the same level line. Install the
terminal block bracket next to the left bracket. This
bracket is used to hold the power and/or controls
terminal block easily out of sight.
Solo/Pro 2 - Installation
terminal block bracket

13
5. Ensure the wall bracket lever is down.
6. Connect the screen terminal block to the pre-wire
terminal block. Then press the connected terminal
block into the mount.
Solo/Pro 2 - Installation
Proper position
for installing
screen

14
7. Hang the screen on the mounting brackets ensuring
that all hooks are engaged in the channel in the back
of the cassette.
Solo/Pro 2 - Installation
Hanging the screen, will require 2 people.