SI ZERO EDGE PRO User manual

INSTALLERS: PLEASE BE SURE TO LEAVE THIS
MANUAL WITH THE OWNER. THANK YOU!
ZERO EDGE PRO
Owner’s Manual
TM

Screen Innovations warrants its products, to the original purchaser only, to be
free from defects in materials and workmanship for a period of one (1) year
from the date of purchase by the original purchaser provided they are properly
operated according to Screen Innovations’ instructions and are not damaged
due to improper handling or treatment after shipment from the factory.
This warranty does not apply to equipment showing evidence of misuse, abuse,
or accidental damage, or which has been tampered with or repaired by a person
other than authorized Screen Innovations personnel.
Screen Innovations’ sole obligation under this warranty shall be to repair or to
replace (at Screen Innovations’ option) the defective part of the merchandise.
Returns for service should be made to your Screen Innovations’ dealer. If it is
necessary for the dealer to return the screen or part to Screen Innovations,
transportation expenses to and from Screen Innovations are payable by the pur-
chaser and Screen Innovations is not responsible for damage in shipment. To
protect yourself against damage or loss in transit, insure the product and prepay
all transportation expenses.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
WARRANTIES AS TO FITNESS FOR USE AND MERCHANT ABILITY. Any implied warranties of tness
for use, or merchantability, that may be mandated by statute or rule of law are limited to the one (1)
year warranty period. This warranty gives you specic legal rights, and you may also have other
rights, which vary from state-to-state. NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES
RESULTING FROM INTERRUPTION IN OPERATION OF EQUIPMENT, OR FOR INCIDENTAL, DIRECT, OR
CONSEQUENTIAL DAMAGES OF ANY NATURE.
In the event that there is a defect in materials or workmanship of a Screen Innovations product, you
may contact our Sales Partners at 9715-B Burnet Road Suite 400, Austin, TX 78758, [phone].
IMPORTANT: THIS WARRANTY SHALL NOT BE VALID AND SCREEN INNOVATIONS SHALL NOT BE
BOUND BY THIS WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH SCREEN
INNOVATIONS’ WRITTEN INSTRUCTIONS.
Keep your sales receipt to prove the date of purchase and your original ownership.
LIMITED ONE YEAR WARRANTY
ON SCREEN INNOVATIONS PRODUCTS
TM
APPLY S/N
STICKER HERE

TM
ZERO EDGE PRO
3
?
512-832-6939
SCREENINNOVATIONS.COM
9715-B Burnet Road Suite 400, Austin,TX 78758

TM
4
ZERO EDGE PRO
Table of Contents
SUGGESTED PROJECTOR PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
STANDARD FRAME PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
STANDARD FRAME ASSEMBLY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
SPLIT FRAME PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
SPLIT FRAME ASSEMBLY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
LED LIGHTS ATTACHMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
BLACK DIAMOND OR SHORT THROW ATTACHMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
SLATE OR PURE ATTACHMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
BLACK BACKER ATTACHMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
MAESTRO ATTACHMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
BLACK BACKER ATTACHMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
SMALL TRIM ATTACHMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
MEDIUM OR LARGE TRIM ATTACHMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
LOGO ATTACHMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
TRIM REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
WALL INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
FLOWN INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
IR LIGHTING HEX CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
IP CONTROLLED LIGHTING SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

TM
ZERO EDGE PRO
5
SUGGESTED PROJECTOR PLACEMENT
11°
11°
SCREEN
Better
Best
Good
36”-42”
(91cm - 106cm)

TM
6
ZERO EDGE PRO
SPLIT
STANDARD 7
12
PRE ASSEMBLED 39

TM
7
STANDARD
STANDARD FRAME PARTS LIST
2X
1X
Hardware Kit
1X
1X
2X
2X
(LED Lights Only)
Wall Brackets Mounting
Screws
4X
1/4-20 x 1/4’’
Screws
(Small trim only)
4X Thin Corner
Brackets
4X Thick Corner
Brackets
1/8’’ & 5/32’’
Hex Keys
Bungees
(Maestro only)
SI Attachment Bands
(Black Diamond and Short
Throw Only)
4X Gloves
1/2’’ Small trim
option
1 1/2’’ or 2’’
trim option
Acrylic Logo

TM
8
STANDARD
Flying Mount Only
2X Flown Ceiling
Mount
2X Flown
Cable
LED Remote
?
?
?
?
LED IR Controlled Only
2X Flown Screen
Mount
If IP controlled LED lights are ordered, Phillips Hue hub must be
purchased and set up separately. See page 46 for IP lighting Instructions.

TM
9
STANDARD
1
2
Thin Bracket
Thick Bracket
Insert the thin corner brackets into the outside channels and the thick corner brackets
into the inside channels of the vertical frames. Then slide into the channels in the
horizontal frames.
STANDARD FRAME ASSEMBLY

TM
10
STANDARD
4
3
Make sure the points on the frame pieces line up. Then nger tighten 2 of the set screws
to lock in the corners.

TM
11
STANDARD
5
6
A = B
A B
18 20
LED
Measure the diagonals to check if frame is square. If one diagonal is longer then push
on the corners at that diagonal. Tighten all set screws once the diagonals are equal to
within 1/8’’.

TM
12
SPLIT
SPLIT FRAME PARTS LIST
1X 1X
1X 1X
2X
2X 2X
2X
1X
Hardware Kit
1X
(LED Lights Only)
Wall Brackets Mounting
Screws
8X
1/4-20 x 1/4’’
Screws
(Small Trim Only)
4X Thin Corner
Brackets
4X Thick Corner
Brackets
4X Gloves
4X
1/4-20 Wing
nuts
4X
1/4-20 Thumb
Screws
2X Vertical
Support
Brackets
1/8’’ & 5/32’’ or
3/32’’ Hex Keys
1/2’’ Small trim
option
1 1/2’’ or 2’’
Trim option
Acrylic Logo
Bungees
(Maestro only)
SI Attachment
Bands
(Black Diamond and
Short Throw Only)

TM
13
SPLIT
Acrylic Logo
Flying Mount Only
2X Flown Ceiling
Mount
2X Flown
Cable
LED Remote
?
?
?
?
LED IR Controlled Only
2X Flown Screen
Mount
If IP controlled LED lights are ordered, Phillips Hue hub must be
purchased and set up separately, see page 46 for IP lighting Instructions.

TM
14
SPLIT
1
2
Thin Bracket
Thick Bracket
Insert the thin corner brackets into the outside channels and the thick corner brackets
into the inside channels of the vertical frames. Then slide into the channels in the
horizontal frames.
SPLIT FRAME ASSEMBLY

TM
15
SPLIT
3
4
Slide the horizontal frame pieces together and secure with the splice bars. Then attach
the vertical support to the frame as shown.

TM
16
SPLIT
5
6
Make sure the points on the frame pieces line up. Then nger tighten 2 of the set screws
to lock in the corners.

TM
17
SPLIT
7
8
A = B
A B
18 20
LED
Measure the diagonals to check if frame is square. If one diagonal is longer then push
on the corners at that diagonal. Tighten all set screws once the diagonals are equal to
within 1/8’’.

TM
18
ZERO EDGE PROLED LIGHTS ATTACHMENT
1
NOTE: Steps 1 and 2 will have already been completed if possible to be shipped that
way. If so skip to step 3.
Connect the lighting harness with the included screws to the nuts in the frame piece
with the lights attached to it.
2
Plug in the lights to the controller plugs.
If IP controlled LED lights are ordered, Phillips Hue hub must be
purchased and set up separately, see page 50 for IP lighting Instructions.

TM
ZERO EDGE PRO
19
3
Press in the lights to the channel on the frame. Do not crease the lights at the corners.

TM
20
ZERO EDGE PRO
Material?
BLACK DIAMOND or
SHORT THROW
21
MAESTRO
29
SLATE or PURE
25