Siamp SCU 350 User manual

BATICUVETTE/BIDET
SCU 350
ASSEMBLY INSTRUCTIONS

2
DESCRIPTION
o n
l
m
c
d
e
h
i
fg
b
k
p
j
a

3
Tools required:
• Set of keys from 8 to 19mm
• Metal saw
• Drill with a bit diameter 8mm
• Leveller
• Pencil & ruler
• Measuring tape
• Hammer
• Screwdriver
Advice:
• Keep this notice for any future maintenance
Read the instructions supplied with
the bowl, the cover, the tank and the
pressurised water supply system before
starting installation work.
Elbow bend xation clip
Elbow bend xation
Pipe xation clip
Pipe xation
Fixation screw and washer ( x4)
Bowl xing strip (x2), length 400mm
Flexible sleeve (x 2)
Bowl xing kit
Metal pegs (x6)
Adjustable legs (x2)
Punch screw
Wall brackets (x2)
Washer (x4)
Wall screw (x4)
Wall plugs (x4)
Collar bidet (x1)
a l
b m
c n
d o
e p
f
g
h
i
Evacuation kit elbow bend Ref. 92 4000-07
Evacuation kit straight Ref. 92 4010-07
ACCESSORIES (not supplied)
Evacuation kit
Elbow bend pipe
Straight pipe
Evacuation
pipe
Evacuation
pipe
j
k

4
TYPES OF INSTALLATION
USEFUL MEASUREMENTS
I
I - Minimum depth of the frame =
140mm
II - Thickness of the cladding
Y – 400 – 80- x mm
Or, x = thickness of the cera-
mics at the bowl xation level
This calculation does not take
into account any constraints
due to the tank or pressurised
water supply.
III - Height : adjustable from
325 to 525mm
IV - Height of the bowl :
400mm (nished oor)
V - maximum thickness of the
nished oor = 185mm
III
VIV
➊ Fixed to a thin partition wall ➋Built in to the rising column
II
y x

5
I - ASSEMBLING THE BOWL FIXATION RODS
II - ADJUSTING THE FRAME HEIGHT
➊ Measure the between-axis of the bowl (A)
➋ Place the rods (f) in the holes in the frame
corresponding to the between-axis and x them
in place with 2 nuts.
➊ Place the frame in its nal position
➋ Unscrew the 4 nuts (k)
➌Adjust the leg heights so that the top of the bowl is at about
400 mm from the nished oor
➍Check that the frame is horizontally level, and screw the
nuts back in.
 If the frame is fixed onto a bare floor, the maximum
thickness of the finished floor should not exceed
185 cm.
A
➊➋
k
f

6
III - PREPARING THE FIXATION
IV - PREPARING THE BOWL WATER SUPPLY
➊Mark the drilling points
➋Remove the frame and drill to a depth of 55 mm at
maximum, using an 8 mm diameter drill bit for ground
metal plugs. For wall plugs use a 10 mm diameter drill
bit, and drill to a depth of 70 mm
➌Move the frame back in place, position the metal pegs
(i) in the holes without any effort
➊Measure the diameter of the feeder pipe at the place where it
will be attached to the xation clip.
➋ Put the xation clip into place (b) using 2 screws and washers
(e) and adjust the height according to the measured diameter.
Marks are engraved on the clip to guide you.
➊
➋
➌
x 6
i
➊
➋
b
e
x 4
o
BOWL installation beginning page 6
BIDET installation beginning page 12

7
V - PREPARING THE BOWL EVACUATION CONNECTION
➊Measure the diameter of the evacuation pipe at the place
where it will be attached to the xation clip.
➋ Attach the xation clip using 2 screws and washers (e) and
adjust the height according to the measured diameter.
Marks are engraved on the clip to guide you.
➋
➋
➋
➋
d
e

8
VII - CONNECTING THE WATER SUPPLY AND BOWL EVACUATION
➊Put the evacuation pipe into place
➋ Attach the pipe using the xation clip (c)
➌Put the elbow bend supply pipe into place
➍ Attach the elbo bend pipe using the xation clip (a)
If you need to unclip, wing nuts are attached to the
xing clips to do this.
c
a
d
b
Wing nuts
Wing nuts
VI - PUTTING THE FRAME INTO PLACE
➊ Put the frame into its nal place and
attach it with the metal pegs, they must
be inserted into the holes without any
effort.
i
n

9
VIII - WATER TRIALS
➊Insert the water supply pipe and the evacuation
pipe into the holes on the bowl.
➋Place the bowl in the frame
➌ Turn the water on and ush
➍Check that the arrival and evacuation pipes are
sealed (watertight)
➎Take the bowl off again
➊
➋
➍
➎
Do the nishings if necessary

10
X - CONNECTING THE BOWL
➍ Carry over this measurement (L) and increase it by
3mm at the end (on the frame side) of each pipe. For
example, if L = 50mm, shorten the pipe by 53mm
➎Cut the pipes with a metal saw
➏ Smoothen the cuts with a le
➐ Measure the thickness of the back of the bowl (B)
➑ If necessary, cut the xation rods (I) so that the part
which sticks out from the wall is equal to (B) + 20mm.
➒ Shorten the exible sleeves so that the part which
sticks out from the wall is equal to (B) – 15mm
➊Using a ruler placed as in the drawing below, make a
mark on the bowl side of the 2 supply pipes.
➋Take the pipes off the bowl and insert them into the
frame. Using a ruler placed as in the drawing below,
make a mark on the wall side of the 2 pipes.
➌ For each of the pipes, measure the distance (L)
between the 2 marks
Read the instructions for the bowl and lid before starting.

11
f
g
B + 20 mm
➓Insert the water supply and
evacuation pipes into the bowl.
Then place the bowl on the two
xation rods.
To make insertion of the supply
and evacuation pipes easier, use
soapy water.
B
XI - ATTACHING THE BOWL
➊When the bowl has been correctly
positioned, attach it using the kit h),
taking care to put the parts on in the
correct order
i = centering washer
ii = metal washer
iii = nut
iv = cover
iii iii iv
X - CONNECTING THE BOWL (continued)

You have just installed a “baticuvette” toilet from SIAMP’s range and we would like
to thank you for putting your trust in us.
We are specialists in bathroom technical equipment and accessories and have taken
the utmost care in the design and manufacturing of this product, which we guarantee
for 10 years, excluding rubber parts and man hours.
For any more information or requests, please contact your sales outlet.
Or contact us directly at:
Réf. 50 6098 01
IV - BIDET CONNECTION
VI - WATER TRIAL
V - PUTTING THE FRAME INTO PLACE
VII - FINAL INSTALLATION
➊Mount bidet collar onto frame.
Install bidet water supply and drain.
Install bidet directly onto frame but without
cladding. Make a water test checking no water
leakage is occurring. Uninstall bidet from the
frame.
➊ Put the frame into its nal place and attach it with
the metal pegs, they must be inserted into the
holes without any effort.
Create cladding. Install Bidet.
12
Siamp Ltd, Unit C2, Meadowbank Business Park, Tweedale Way
Hollinwood, Oldham, Grater Manchester, OL9 8EH
T : 0161 681 2120 F : 0161 681 2130 E : [email protected]
Technical support : [email protected] W : www.siamp.co.uk