Siamp Optima 49 User manual

✘
✘✘ ✔
Vitra S20 Troubleshooting
Sticking or not flushing
Passing water
First check that the valve position is as shown above,
the valve should be clear of the cistern wall, if not
remove the valve and re-position.
If the valve position is correct, check the valve settings
are still in the factory set positions detailed in the table
(right).
If the problem persists please contact Siamp Aftersales
on 0161 681 2120 or [email protected]
No Description Setting Figure
1 Stirrup Position 7 (number 6 will be visible) A
2 Lift Rod Position 5 (4 holes above will be visible) B
3 Overflow Factory set. D will be visible B
4 Residual Water 0 C
5 Short flush cursor 10 D

Fig A.
Stirrup in position 7.
(number 6 will be visible)
Fig B.
Lift Rod in position 5
(4 holes visible above)
Overflow tube pre-cut at D
Fig C.
Residual Water set at 0
Fig D.
Short flush cursor set at 10
Vitra S20 Troubleshooting
Sticking or not flushing
Passing water

OPTIMA 49
ASSEMBLY INSTRUCTIONS
Button
Short flush
Long flush
Optional escutcheon
(not always supplied)
Lift rod
Residual sliding valve
Strainer
Strainer nut
Pan gasket
Strainer gasket
Valve gasket
Stirrup
catch clip
Overflow
Stirrup
Ref.: 50 5498 01
a
b
c
d
e
f
g
h
i
k
l
m
GB
Short
flush
cursor
j
N 50N 100

I - PREPARING THE MECHANISM
II - INSTALLATION
Check the position of the stirrup
If the stirrup (m) is correctly positioned
on the basis of the below table, proceed
to step ➏. Otherwise, carry out all of the
following steps:
➊Unclip the lift rod (c)
➋Remove the stirrup (m) , by pressing on
the two catch clips (k)
➌Cut the overflow (l) if necessary according
to the table
➍Reposition the stirrup in its seat and slide
it to the required position (desired setting
notch number visible)
➎Clip lift rod (c) back into the hole of the
overflow (l) which has the same number as
that of the setting notch
➏Unscrew the strainer nut (f)
Measure the cistern
-H (from the top of the lid to the inside base of the cistern)
-D (diameter of the hole in the lid)
Height Hof cistern
Diameter D Diameter D
of hole in lid of hole
18 to 38 mm in lid
and 38 to
45 to 50 mm 44 mm
11 430 to 417 448 to 435
10 416 to 405 434 to 423
9 404 to 393 422 to 411
8 392 to 381 410 to 399
7 380 to 369 398 to 387
6 368 to 357 386 to 375
5 356 to 345 374 to 363
4 344 to 333 362 to 351
3 332 to 321 350 to 339
2 320 to 309 338 to 327
1 308 to 297 326 to 315
Mini 296 to 282 314 to 300
No. of notch visible on lift rod
H
D
➌
➍
➎
Stirrup notch Cut on overflow tube
3 C mark visible
2 F mark visible
1 I mark visible
Mini L mark visible
Position the mechanism
in the cistern and secure
it in place with the nut (f)
Manually screw the
flush valve nut (f) until
it is in contact with
the ceramic. If
necessary give an
extra quarter turn
(maximum) with the
appropriate spanner.
NB : Excessive
tightening can damage
the mechanism and
would not be covered by
the guarantee.
➊
➋
➊+ ➋=
Visible stirrup notch
no. 4 = position of lift rod no. 4

IV - SETTING WATER LEVELIII - ASSEMBLING BOWL AND CISTERN
V - INSTALLATION OF BUTTON
VI - MAINTENANCE
Bottom of cistern
Wall of bowl
Conical seal
Hexagon nut
Washer
Wing nut
Washer
➊Fix screws at the bottom
of the cistern (see order of
parts below)
➋Position the latex foam
gasket on the nut (f)
➌Position the cistern on
the bowl and secure it
with wing nuts
Changing the valve gasket
➊After having opened
the cistern, turn the
mechanism 90° to
separate it from its
strainer
➋Change the valve
gasket
➌Reposition the
mechanism, locking it
into the strainer
➍Close the cistern
again.
Valve gasket
Strainer
After having connected your ballcock to the water
supply, open the tap and set the level of the long flush
using the ballcock (see overleaf).
Note: The max. water level should be 20 mm lower
than the overflow tube (l).
To adjust the water level of the short flush, slide the
cursor along (j). Immerse the cursor of 40 mm.
Note : The closer the cursor is to 18, the more
water will be flushed.
➊Once the set-up has been completed, put on the lid
on the cistern
➋If the hole in the lid (D) is > 38 mm and < 45 mm,
remove the escutcheon (b)
➌Position the button on the lid and screw until tight.
20 mm
Overflow
Max.
water level
In some (rare) cases, the residual water level
(amount of water remaining after the long flush)
must be increased to ensure more efficient
cleaning. To do this, move the sliding valve (d) to
the left (the more it is open, the more the residual
water increases).
Note: Increasing the residual water reduces the
volume of water flushed. If necessary, readjust the
max. water level using the ballcock.
M6x78 screw
WATER LEVEL MAX 6L - MIN 4.5L PER FLUSH

Fiber gasket
INSTALLING THE FLOAT VALVE
ROBECO 06 and STANDARD 15EL
MAINTENANCE (95L & 99B)
4, quai Antoine 1er - BP 219 - MC 98007 MONACO Cedex
Tél. [phone] - Fax : [phone] - E-mail: [email protected]
➊Position valve
➋Fasten with nut
➌Connect to water supply
➍Adjust water level with the adjustment screw
➊Position valve
➋Fasten with nut
➌Connect to water supply
➍Adjust water level with the adjustment screw
(15 EL) or by bending the rod (06)
COMPACT 99B and HANDY 93B
COMPACT 95L
Adjustment screw
Insert rod
as far as
possible Locking nut
Fiber gasket
Adjustment screw
Locking nut
Fiber gasket
Adjustment
screw
Locking nut
Locking nut
Gasket/filter
Adjustment screw
Filter
Membrane
Membrane
Manually screw the backnut until it is in contact with the
ceramic. If necessary give an extra quarter turn (maximum).
N.B.: Excessive tightening can damage the mechanism and
would not be covered by the guarantee.
Ensure tightness of connection to cistern with filter gasket.
WARNINGS:
1 - Do not overtight in any case.
2 - Do not use any sealing paste and/or compound in any
case
3 - Do not use connector handling the internal part of the
inlet valve.
SIAMP will be not responsible in case these warnings
are not respected.
N 50N 100
Siamp UK Ltd - Unit C2 - Meadowbank Business Park - Tweedale Way
Hollinwood - Oldham - Greater Manchester - OL9 8EH
Telephone : [phone] - Fax : [phone] - [email protected]