Siemens FC72x User manual

FC72x / FT724
Fire control panel / fire terminal
Quick Reference Guide
IP6
A6V10211094_f_en_--
Building Technologies
2015-12-15 Control Products and Systems

Legal notice
2 | 62
Building Technologies
A6V10211094_f_en_
--
Fire Safety
2015
-
12
-
15
Legal notice
Technical specifications and availability subject to change without notice.
Transmittal, reproduction, dissemination and/or editing of this document as well as
utilization of its contents and communication thereof to others without express
authorization are prohibited. Offenders will be held liable for payment of damages.
All rights created by patent grant or registration of a utility model or design patent
are reserved.
Issued by:
Siemens Switzerland Ltd.
Building Technologies Division
International Headquarters
Gubelstrasse 22
CH-6301 Zug
Tel. [phone]
www.siemens.com/buildingtechnologies
Edition: 2015-12-15
Document ID: A6V10211094_f_en_--
© Siemens Switzerland Ltd, 2009

3 | 62
Building Technologies
A6V10211094_f_en_
--
Fire Safety
2015
-
12
-
15
Table of contents
1About this document .............................................................................5
1.1 Applicable documents................................................................................. 6
1.2 Download center......................................................................................... 7
1.3 Technical terms and abbreviations.............................................................. 7
1.4 Revision history .......................................................................................... 7
2Safety instructions ................................................................................8
2.1 Safety regulations for the method of operation ............................................ 9
2.2 Standards and directives complied with......................................................11
2.3 Responsibility of the operator.....................................................................11
3System overview ................................................................................ 12
3.1 Station overview ........................................................................................14
4Mounting ........................................................................................... 15
4.1 Mounting instructions.................................................................................16
5Installation ......................................................................................... 17
5.1 Position of printed circuit boards / components...........................................18
5.2 Power supply - mains voltage connection...................................................19
5.2.1 Emergency power supply............................................................21
5.3 Hardware components...............................................................................22
5.3.1 Periphery board ..........................................................................22
5.3.2 Relay for fault and alarm (RT activation)......................................24
5.3.3 Monitored outputs for alarm and fault (FT activation) ...................25
5.3.4 Connection of monitored acoustic signal transmitters ..................27
5.3.5 Configurable inputs/outputs and supply voltage Vsys ..................28
5.4 C-NET detector line ...................................................................................31
5.5 Connectable C-NET devices......................................................................32
5.6 C-NET topology and connection ................................................................36
5.7 Wiring principle behind C-NET devices ......................................................39
5.8 C-WEB network.........................................................................................40
6Indication and operating elements ........................................................ 43
6.1 Extra indication and operating devices.......................................................45
7Commissioning .................................................................................. 46
7.1 Activating access level...............................................................................47
7.1.1 Log in / Change access level.......................................................47
7.2 Auto-configuration of control panels ...........................................................48
7.2.1 Auto-configure line ......................................................................49
7.3 Displaying C-NET devices .........................................................................52
7.4 Entering/Changing customer text ...............................................................54
7.5 Setting the system time..............................................................................54
7.5.1 Setting time and date ..................................................................54
7.6 Changing access authorization PIN ...........................................................55
7.6.1 PIN administration.......................................................................55
7.7 Restart the station......................................................................................57

Building Technologies
A6V10211094_f_en_
--
Fire
Safety
2015
-
12
-
15
4 | 62
8Testing the installation .........................................................................59
8.1 Checking functions ....................................................................................59
Glossary .....................................................................................................60
Index .........................................................................................................61

About this document
Applicable documents
1
5 |
62
Building Technologies
A6V10211094_f_en_
--
Fire Safety
2015
-
12
-
15
1About this document
Goal and purpose
These brief instructions aim to provide experienced and qualified installation and
operating staff with a guide on how to mount, install, commission and repair the
system.
Scope
These brief instructions are supplements to the documents provided for the
Cerberus PRO FS720 fire detection system and apply for the following products:
●Fire control panel FC722, FC724
●FT724 fire terminal
These brief instructions only apply to use with C-NET detector line cable and when
commissioning with auto-configuration. They do not include other applications
and/or components of extended networking.
The information contained in this document is valid for introduction package IP6.
Target groups
The information in this document is intended for the following target groups:
Target group Activity Qualification
Installation personnel ●Assembles and installs the
product components at the place
of installation.
●Carries out a function check
following installation.
●Has received specialist training in the
area of building installation technology
or electrical installations.
Operating personnel ●Carries out procedures to
correctly operate the product.
●No particular basic training is needed.
●Has been instructed by the
commissioning personnel.
Source language and reference document
●The source/original language of this document is German (de).
●The reference version of this document is the international version in English.
The international version is not localized.
Document identification
The document ID is structured as follows:
ID code Examples
ID_ModificationIndex_Language_COUNTRY
-- = multilingual or international
A6V10215123_a_de_DE
A6V10215123_a_en_--
A6V10315123_a_--_--
Date format
The date format in the document corresponds to the recommendation of
international standard ISO 8601 (format YYYY-MM-DD).

About this document
Applicable documents
1
6 | 62
Building Technologies
A6V10211094_f_en_
--
Fire Safety
2015
-
12
-
15
Conventions for text marking
Markups
Special markups are shown in this document as follows:
⊳Requirement for a behavior instruction
1.
2.
Behavior instruction with at least two operation sequences
– Version, option, or detailed information for a behavior instruction
⇨Intermediate result of a behavior instruction
⇨End result of a behavior instruction
●Numbered lists and behavior instructions with an operation
sequence
[➙ X] Reference to a page number
'Text' Quotation, reproduced identically
<Key> Identification of keys
>Relation sign and for identification between steps in a sequence,
e.g., 'Menu bar' > 'Help' > 'Help topics'
↑Text Identification of a glossary entry
Supplementary information and tips
The 'i' symbol identifies supplementary information and tips for an easier way
of
working.
1.1 Applicable documents
Document ID Title
A6V10210355 System description
A6V10210362 Planning
A6V10210390 Mounting / Installation
A6V10210416 Commissioning / Maintenance / Troubleshooting
A6V10210424 Configuration
A6V10229261 List of compatibility
A6V1021 0368 Product data
A6V10211118 Quantities Tool

About this document
Download center
1
7 |
62
Building Technologies
A6V10211094_f_en_
--
Fire Safety
2015
-
12
-
15
1.2 Download center
You can download various types of documents, such as data sheets, installation
instructions, and license texts via the following Internet address:
http://siemens.com/bt/download
κEnter the document ID in the 'Find by keyword' input box.
You will also find information about search variants and links to mobile
applications (apps) for various systems on the home page.
1.3 Technical terms and abbreviations
You will find details of technical terms and abbreviations in the 'Glossary' chapter.
1.4 Revision history
The reference document's modification index applies to all languages into which
the reference document is translated.
The first edition of a language version or a country variant may, for
example, have
the modification index 'd' instead of 'a' if the reference document already has this
modification index.
The table below shows this document's revision history:
Version Edition date Brief description
f 2015-12-15 Edition: Introduction Package IP6
●Referenced documents updated
●'Station overview' chapter: Ethernet switch (modular) integrated
●'C-WEB network' chapter: Data rate changed to 315 kbit/s
●C-NET detector line updated
e 2014-02-10 Information on voltage ranges revised in the chapter 'Configurable inputs/outputs
and supply voltage Vsys'
d 2013-11-14 Edition: Introduction Package IP5
●Change to date format according to ISO 8601
●C-NET devices added: FDCI723, FDM223-Ex, OOH740-A9-Ex, FDCL221-Ex,
FDA221, FDA241, FDM273, FDM243H
●License key (Sx) replaces license key (Lx)
CPR replaces CPD: The Construction Products Regulation (CPR 305/2011)
replaces the previous Construction Products Directive (CPD 89/106).
New:
●LED module FTO2008-A1 with 24 red/green and yellow LEDs each
c 2012-06 Edition: Introduction Package IP4
●C-NET devices updated
b 2010-07 ●Adaptation to MP3.0 XS
●Adaptation of naming
●Various minor corrections
a 2009-05 First edition MP1XS

Safety instructions
Revision history
2
8 | 62
Building Technologies
A6V10211094_f_en_
--
Fire Safety
2015
-
12
-
15
2Safety instructions
The safety notices must be observed in order to protect people and property.
The safety notices in this document contain the following elements:
●Symbol for danger
●Signal word
●Nature and origin of the danger
●Consequences if the danger occurs
●Measures or prohibitions for danger avoidance
Symbol for danger
This is the symbol for danger. It warns of risks of injury.
Follow all measures identified by this symbol to avoid injury or death.
Additional danger symbols
These symbols indicate general dangers, the type of danger or possible
consequences, measures and prohibitions, examples of which are shown in the
following table:
General danger Explosive atmosphere
Voltage/electric shock Laser light
Battery Heat
Signal word
The signal word classifies the danger as defined in the following table:
Signal word Danger level
DANGER DANGER identifies a dangerous situation, which will result directly in death or
serious injury if you do not avoid this situation.
WARNING WARNING identifies a dangerous situation, which may result in death or serious
injury if you do not avoid this situation.
CAUTION CAUTION identifies a dangerous situation, which could result in slight to
moderately serious injury if you do not avoid this situation.
NOTICE NOTICE
identifies possible damage to property that may result from non-
observance.
How risk of injury is presented
Information about the risk of injury is shown as follows:
WARNING
Nature and origin of the danger
Consequences if the danger occurs
●
Measures / prohibitions for danger avoidance

Safety instructions
Safety regulations for the method of operation
2
9 | 6
2
Building Technologies
A6V10211094_f_en_
--
Fire Safety
2015
-
12
-
15
How possible damage to property is presented
Information about possible damage to property is shown as follows:
NOTICE
Nature and origin of the danger
Consequences if the danger occurs
●
Measures /
prohibitions for danger avoidance
2.1 Safety regulations for the method of operation
National standards, regulations and legislation
Siemens products are developed and produced in compliance with the relevant
European and international safety standards. Should additional national or local
safety standards or legislation concerning the planning, mounting, installation,
operation or disposal of the product apply at the place of operation, then these
must also be taken into account together with the safety regulations in the product
documentation.
Electrical installations
WARNING
Electrical voltage
Electric shock
●Work on electrical installations may only be carried out by qualified
electricians or by instructed persons working under the guidance and
supervision of a qualified electrician, in accordance with the electrotechnical
regulations.
●Wherever possible disconnect products from the power supply when carrying
out commissioning, maintenance or repair work on them.
●Lock volt-free areas to prevent them being switched back on again by mistake.
●Label the connection terminals with external external voltage using a
'DANGER External voltage' sign.
●Route mains connections to products separately and fuse them with their own,
clearly marked fuse.
●Fit an easily accessible disconnecting device in accordance with IEC 60950-1
outside the installation.
●Produce earthing as stated in local safety regulations.
CAUTION
Noncompliance with the following safety regulations
Risk of injury to persons and damage to property
●
Compliance with the following regulations is required.
●Specialist electrical engineering knowledge is required for installation.
●Only an expert is permitted to carry out installation work.
Incorrect installation can take safety devices out of operation unbeknown to a
layperson.

Safety instructions
Safety regulations for the method of operation
2
10 | 62
Building Technologies
A6V10211094_f_en_
--
Fire Safety
2015
-
12
-
15
Mounting, installation, commissioning and maintenance
●If you require tools such as a ladder, these must be safe and must be intended
for the work in hand.
●When starting the fire control panel ensure that unstable conditions cannot
arise.
●Ensure that all points listed in the 'Testing the product operability' section below
are observed.
●You may only set controls to normal function when the product operability has
been completely tested and the system has been handed over to the customer.
Testing the product operability
●Prevent the remote transmission from triggering erroneously.
●If testing building installations or activating devices from third-party companies,
you must collaborate with the people appointed.
●The activation of fire control installations for test purposes must not cause
injury to anyone or damage to the building installations. The following
instructions must be observed:
–Use the correct potential for activation; this is generally the potential of the
building installation.
–Only check controls up to the interface (relay with blocking option).
– Make sure that only the controls to be tested are activated.
●Inform people before testing the alarm devices and allow for possible panic
responses.
●Inform people about any noise or mist which may be produced.
●Before testing the remote transmission, inform the corresponding alarm and
fault signal receiving stations.
Modifications to the system design and the products
Modifications to the system and to individual products may lead to faults,
malfunctioning and safety risks. Written confirmation must be obtained from
Siemens and the corresponding safety bodies for modifications or additions.
Modules and spare parts
●Components and spare parts must comply with the technical specifications
defined by Siemens. Only use products specified or recommended by
Siemens.
●Only use fuses with the specified fuse characteristics.
●Wrong battery types and improper battery changing lead to a risk of explosion.
Only use the same battery type or an equivalent battery type recommended by
Siemens.
●Batteries must be disposed of in an environmentally friendly manner. Observe
national guidelines and regulations.
Disregard of the safety regulations
Before they are delivered, Siemens products are tested to ensure they function
correctly when used properly. Siemens disclaims all liability for damage or injuries
caused by the incorrect application of the instructions or the disregard of danger
warnings contained in the documentation. This applies in particular to the following
damage:
●Personal injuries or damage to property caused by improper use and incorrect
application
●Personal injuries or damage to property caused by disregarding safety
instructions in the documentation or on the product
●Personal injury or damage to property caused by poor maintenance or lack of
maintenance

Safety instructions
Standards and directives complied with
2
11 |
62
Building Technologies
A6V10211094_f_en_
--
Fire Safety
2015
-
12
-
15
2.2 Standards and directives complied with
A list of the standards and directives complied with is available from your Siemens
contact.
2.3 Responsibility of the operator
A fire detection installation is a piece of safety engineering equipment designed to
protect people, buildings and equipment through early detection of fires and
alarming.
The fire detection installation has to be maintained in order to satisfy this
requirement. Within the European Union, the maintenance intervals are defined in
the EN 54 standard and/or are also governed by national and local requirements.
Maintenance is required in order for the fire detection installation to function
correctly. The fire detection installation consists of components the function of
which may be impaired by ambient conditions and aging.
Maintenance of a fire detection installation is governed by the EN54 standard.
Manufacturer's recommendations
The following work should be carried out at regular intervals to maintain the fire
detection system:
●Visual check for damage on the devices or possible sources of error
●Quarterly inspection of system parts including test triggering of fire alarm
●Annual maintenance including inspection work, checking the power supply and
emergency power supply
●Replacement of batteries by the date stated by the battery manufacturer at the
latest (printed on battery)
●Keep a logbook to document system messages, isolations and maintenance
work.
The frequency of
inspections and service work is dependent on the ambient
conditions.
If using fire detection systems in critical ambient conditions, e.g. in rooms with a
high concentration of dust, high air humidity or large temperature fluctuations,
shorter inspection intervals may be needed.

System overview
Responsibility of the operator
3
12 | 62
Building Technologies
A6V10211094_f_en_
--
Fire Safety
2015
-
12
-
15
3System overview
The FC720 Cerberus PRO fire control panels can be operated as standalone
panels or networked into a fire detection system. Up to 32 stations (fire control
panels, fire terminals) are networked via the C-WEB/SAFEDLINK system bus. The
Cerberus PRO fire control panels support operation of the C-NET detector line.
1 FC722 or FC724 fire control panel in Comfort housing
2 FC722 fire control panel in the Standard housing
3 FT724 fire terminal
4 Laptop or PC with Cerberus-Engineering-Tool software
5 C-NET detector line
6Periphery e.g. RT alarm transmission installation or acoustic signal
transmitter etc.
b
e
1
2
3
j
l
n
4
5
6
h
i
u
7
8
9
q
0
#
C
Ce rb er us
TM
a
b
d
e
1 2 3
n
o
4 5 6
g
h
u
7 8 9
p
q
0 #
C
Cer ber us
TM
a
b
d
e
1
2
3
n
o
4
5
6
g
h
u
7
8
9
p
q
0
#
C
Cer ber us
TM
a
b
d
e
1
2
3
n
o
4
5
6
g
h
u
7
8
9
p
q
0
#
C
Cer ber us
TM

System overview
Responsibility of the operator
3
13 |
62
Building Technologies
A6V10211094_f_en_
--
Fire Safety
2015
-
12
-
15
C-NET detector line
The C-NET is a monitored bus line using 2-wire technology, to which up to 252
devices per loop or 32 devices per stub can be connected. C-NET line devices are
automatic fire detectors, manual call points, I/O components, transponders, and
indication and operating devices such as floor repeater terminals. With the
exception of the FDCIO223 transponder, which requires its own power supply, all
C-NET line devices are also supplied with operating voltage via the C-NET. There
is a line separator integrated in each line device. In the event of a C-NET fault
(short-circuit/wire break), the defective line segment is isolated by two neighboring
line separators. When using a loop, the connected devices remain ready to detect.
With a stub, the faulty line segment is isolated after the line separator. The fault is
displayed on the station.
C-WEB/SAFEDLINK
Up to 32 Cerberus PRO stations can be networked via the C-WEB to form a
system. Redundant operations are guaranteed by the network's ring topology.
Thanks to the C-WEB, system-wide alarming and access to individual fire detection
system devices is possible. There may be a distance of up to 1000 m in the C-
WEB between two stations. At greater distances, special repeaters or even optical
waveguide connections can be used. A second network card can also be fitted for
stricter fail-safe requirements (EN54).
The network connection can also be realized by the Ethernet with limitations.
However this does not satisfy the requirements of EN54.
More details of networking can be found in the system documentation.

System overview
Station
overview
3
14 | 62
Building Technologies
A6V10211094_f_en_
--
Fire Safety
2015
-
12
-
15
3.1 Station overview
FC722
fire control panel
(2-loop)
FC724
fire control panel
(4-loop)
FT724
fire terminal
Max. C-NET addresses 252 * 504 * ―
Without loop extension 2 loops * 4 loops * ―
With loop extension 4 loops * 8 loops * ―
Supply
Power supply 70/150 W 150 W optional (70 W)
Batteries (capacity) max. 2x 26 Ah max. 2 x 26 Ah optional (7 Ah)
External DC supply 24 V ― ― redundant
Operating unit integrated integrated integrated
Inputs and outputs
RT alarm, relay 1 1 ―
RT fault, relay 1 1 ―
RT alarm monitored 1 1 ―
RT fault monitored 1 1 ―
Outputs for monitored, acoustic
signal transmitter
1 2 ―
Freely configurable
inputs/outputs
8 12 ―
Options
Loop extension (C-NET) max. 1 max. 2 ―
Network module (SAFEDLINK) max. 2 max. 2 max. 2
Ethernet switch (modular) max. 1 max. 1 external
Repeater (SAFEDLINK) max. 1* max. 1* max. 1*
RS232 / RS485 module max. 2 max. 2 max. 2
Fire brigade periphery module
[DE]
1 1 ―
Event printer 1 1 1
LED module; 24 red/green and
yellow LEDs each
max. 5 max. 5 max. 5
EVAC-NL operating unit [NL] max. 1 max. 1 max. 1
Sounder module max. 2 max. 2 ―
RT interface [NL] max. 1 max. 1 ―
License keys max. 1 max. 1 max. 1
Key switch
(Kaba type)
max. 1 max. 1 max. 1
* Note system limits!
The description of system components and options does not form part of these
brief instructions (For detailed information, refer to the system documentation).
[DE] option for Germany [NL] option for the Netherlands

Mounting
Station overview
4
15 |
62
Building Technologies
A6V10211094_f_en_
--
Fire Safety
2015
-
12
-
15
4Mounting
Before mounting and installation, check all the fire detection installation
components visually for damage caused by improper transport and handling.
Figure 1: Unpacking and checking
Components with clear signs of damage must not be used in the station or
operated as fire detection installation components. When assembling the station
and its modules, observe national and local standards and requirements. The
following mounting instructions refer to the specifications of the EN 54 standard
and the manufacturer's recommendations. The site chosen to assemble the station
and associated components must match the planning documents for the fire
detection installation.
C
Cerberus
TM

Mounting
Mounting instructions
4
16 | 62
Building Technologies
A6V10211094_f_en_
--
Fire Safety
2015
-
12
-
15
4.1 Mounting instructions
The station's equipment pack contains an mounting model with the dimensions
needed and details of the mounting points to assist with mounting.
The station must be assembled in a dry, clean and well vented room.
The station must be assembled at a distance of least one door leaf width from the
room's entrance. Select the height of mounting such that the display and optical
indications are approx. 1.6 -1.7m above where the observer stands.
The station and its components should be protected from dampness and interfering
external influences such as dust, great temperature fluctuations and mechanical
stress.
The station must be assembled in a place freely accessible to authorized staff and
the emergency services.
A level, non-vibrating wall surface with load bearing capacity and suitable mounting
materials (e.g. screws and plugs) are needed to secure the station to the wall.
The mounting surface and selected mounting must be suitable for the weight of the
equipped station incl. the batteries used.
The station may only be fitted using the 19" method if using the associated
components.
Mounting is not permitted in rooms with high levels of electromagnetic interference,
e.g. in control rooms or right next to power cables and inductive loads.
WARNING
Electric shock
Mounting and installation work may only be undertaken by qualified staff and
when the system is de-energized.
NOTICE
Damage resulting from electrostatics
Take appropriate EMC protective measures when handling electronics modules.

Installation
Mounting instructions
5
17 |
62
Building Technologies
A6V10211094_f_en_
--
Fire Safety
2015
-
12
-
15
5Installation
The following installation instructions refer to the specifications of the EN 54
standard and the manufacturer's recommendations. The installation may only be
undertaken by an electrician. Detailed instructions can be found in the system
documentation.
●Use a suitable cable, e.g., NYM 3 x 1.5 mm2(max. 2.5 mm²) or a cable type
with similar performance features to connect the AC voltage from the line
supply.
●The line voltage fuse must be designed for a current level of 10 A.
●The mains connection cable must be routed into the control panel housing from
above or from the rear.
●Provide a suitable mains separator or an appropriately labeled automatic cutout
for the mains voltage connection.
●The nominal voltage required (AC 230 V or AC 115 V) is stated on the control
panel type plate.
●Use a separate residual current unit for residual current circuit breakers.
Depending on the installation conditions, voltage surge protection (primary
protection) is required for the mains connection.
Planning and system limits
Before the installation, check whether the system's planning is suitable for the
system limits. This applies e.g. to all technical data and details of cable lengths,
number of line devices, number of networked stations, battery capacity and
compliance with requirements from standards and national guidelines and local
requirements.
Details of planning can be found in the system documentation.
Information about lightning protection
Further information and detailed specifications relating to producing a lightning
protection concept can be found in the relevant literature and associated
standards.
WARNING
High voltage! Danger to life!
Risk of electric shock
●Mounting and installation work may only be undertaken by qualified staff and
when the system is de-energized.
●Only use cable openings or the edge protection strips provided to protect
cables.
NOTICE
Overvoltage
Damage possible
●Observe the nominal voltage required (AC 230 V) as per the control panel
type plate!
●The fuses used and stated in the factory must not be bypassed or replaced
with any type other than that stated.
●Take appropriate EMC protective measures when handling electronics
modu
les.

Installation
Position of printed circuit boards / components
5
18 | 62
Building Technologies
A6V10211094_f_en_
--
Fire Safety
2015
-
12
-
15
5.1 Position of printed circuit boards / components
Figure 2: Position of components in housing (Standard) for FC722
Figure 3: Position of components in housing (Comfort) for FC722 or FC724
1 Batteries 6 Mains connection terminals (L1,N,PE)
2 Power supply (70 W) 7 Loop extension option (C-NET) 1 x for FC722, 2 x for FC724
3 Power supply (150 W) 8 Shield connection terminal blocks or cable kit option
(communication)
4 Periphery board (2 loops) 9 Space for more options, e.g. fire brigade periphery module
5Periphery board (2 loops or 4
loops)
10 Type plate
You will find further information on removing the FC722 and FC724 stations and
the housings and options available in the system documentation.
After mounting the type plate must be stuck to the outside of the housing in a
clearly visible location and the mounting date added.

Installation
Power supply
-
mains voltage connection
5
19 |
62
Building Technologies
A6V10211094_f_en_
--
Fire Safety
2015
-
12
-
15
5.2 Power supply - mains voltage connection
When supplied from the factory, the power supply's internal cabling is already
connected.
Power units available
24 V DC/2.5 A, power 70 W, max. battery capacity which can be connected 17 Ah
24 V DC/5 A, power 150 W, max. battery capacity which can be connected 45 Ah
Figure 4: Mains connection in Standard and Comfort housings
1 EMC-critical zone (no high-voltage power permitted) 4 Cable strain relief for mains supply line
2Mains connection from below (not permitted when batteries
are fitted)
5Mains connection from above
(recommended)
3 Power supply terminals 6 EMC boundary
●The network cables must be inserted from above.
●The mains lead must be placed along the left side of the housing (observe
EMC zone boundary).
●Signal and control lines must only be fed into the housing on the right from
above or from the rear.
●Batteries must be installed in the correct positions.
●No cable openings should be made in the base of the housing, unless an
additional empty housing is mounted below the station to accommodate the
batteries.
●The mains connection voltage needed (230 V AC/115 V AC) can be found on
the station's type plate.
2
3
5 6
1
4
2
3
4
5
1
6

Installation
Power supp
ly
-
mains voltage connection
5
20 | 62
Building Technologies
A6V10211094_f_en_
--
Fire Safety
2015
-
12
-
15
Connecting mains voltage
WARNING
Voltage
Electric shock
●Before connecting the mains voltage ensure that it is not energized and is
locked to prevent it being
activated.
Figure 5: Mains connection for Standard and Comfort housings
1Mains cable (supplied from above), 3 x 1.5 mm2
e.g. NYM cable type
6Cable tie
2 Strain relief clamp PE Protective conductor (terminal on the left)
3 Ground on the rear panel N Neutral conductor (terminal in the middle)
4 Disconnect terminal L1 External conductor (terminal on the right, with
mains disconnector)
5 Primary cabling for power supply
1. Lay the mains cable (1) along the left side of the housing.
2. Insulate the mains cable as needed and connect it to the power supply
terminals (PE, L1, N). Use cable end sleeves for wires.
3. Fixate the cable with the strain relief clamp (2).
4. Secure the cable with cable ties (6).
L1
N
PE
4
1
6
3
L1
N
PE
1
2
3
5
5
2
4