Siemens FC901 User manual

FC2005/FC901
System installation instruction
Wiring diagram
Software clearance declaration
Fire Safety & Security Products
Building Technologies
FC901 FC2005

Accessories and separate parts
Accessory
items Content Installation instruction Qty
1
2
3
4
5
6
7
8
9
10
11
S1
S2
1.1
1.2
2.2
2.1
2.3
3.1
3.2
3.3
4.1
4.2
5.1
5.2
Cable between batteries, refer to figure 1 1
Cable between batteries and main board, refer to figure 1,figure 2 1
Cable between City tie board and main board, refer to figure 2 1
Earth cable between enclosure and main board, refer to figure 1 and
figure 2 1
Grounding cable for front door and power supply,
refer to figure 1 2
Battery bracket left, refer to figure 1 1
Battery bracket right, refer to figure 1 1
Cable ties 10
No.8 screws, refer to figure 1 12
No.4 screws, refer to figure 2 2
Spacer for City tie board, refer to figure 2 2
Battery cell, refer to figure 1 2
Power supply, refer to power supply installation instruction sheet
delivered with power supply 1
Assembling notes
1. Mount the batteries with battery brackets.
2. Mount the power supply MOV, then mount the power supply to the enclosure.
3. Mount the City tie module onto the main board according to the Figure 2 (City tie module is optional).
4. Connect the cables to the corresponding position marked on the drawing
(The power supply input cable and output cable are not included in the FC901 and FC2005 package).
4. Tie the cables to the enclosure with cable tie, refer to the Figure 1(Cable tie features).
5. Mount the Main board assembly onto the Enclosure according to Figure 3.
6. Mount the Lock pin to the Front door axis(Both are included in the Enclosure package)
S3 Front door hinge axis lock pin, refer to Detail A 2
S4 Front door hinge axis, refer to Detail A 2
Document ID: A5Q00039713A
Page 1/12 02.2012
Fire Safety & Security Products
Building Technologies FC2005/FC901 installation instruction
S5 2
EOL for NAC, refer to Detail C
Note: Item 3,6,7,11,S1and S2 are not delivered with the FC901 and FC2005.And should be ordered separately.
FC2005/FC901 installation instruction
12 Power supply MOV(Metal Oxide Varistor), refer to figure 2 1

Battery, Power supply and City tie PCB assembly installation instruction
FC2005/FC901 installation instruction
Pay attention to the battery polarity at 2.1 and 2.2
Brownout
S1
9
7
6
GNDGND +26
S2
Figure 1 Installation instruction(Front view with front door open)
1.1 1.22.1 2.2
4.1 and 5.1(1)
5.1(2)
5.2(1)
5.2(2)
Power supply
DC output
Cable tie feature
Detail A
Detail A Front door hinge and lock pin installation instruction
S3
Figure 2 Installation instruction(Main board assembly back view)
10
11
3.2
3.3
3.1
4.2
2.3
Power supply DC input
City tie
module
Detail B
Document ID: A5Q00039713A
Page 2/12 02.2012
Fire Safety & Security Products
Building Technologies FC2005/FC901 installation instruction

Detail B City tie cabling
X2 Output 2
Connect to 3.2
X3 Output 1
Connect to 3.3
From left to right:
TP1295,TP1294,TP1293,TP1292
3.1
From 1 to 4
TP1295,TP1294,TP1293,TP1292
1234
City tie cable,Main board and EOL installation instruction
FC2005/FC901 installation instruction
Figure 3 Main board assembly installation instruction
9
Detail C
Detail C NAC EOL installation instruction
N_BN
-
N_BP
+
N_AN
-
N_AP
+
S5
Document ID: A5Q00039713A
Page 3/12 02.2012
Fire Safety & Security Products
Building Technologies FC2005/FC901 installation instruction

Power supply MOV(Metal Oxide Varistor) Installation instruction
Step 1: Bend the MOV connector pin
refer to the picture for an example
Step 2: Fix or weld the MOV onto the power input
connector.Take the picture as reference
Step 3: Fix the AC input cable and screws on
the connector. Take the picture as reference
FC2005/FC901 installation instruction
Document ID: A5Q00039713A
Page 4/12 02.2012
Fire Safety & Security Products
Building Technologies FC2005/FC901 installation instruction

Installation instruction without Trim kit
18 1/8” 5 7/64”
16 ½”
8 1/4”
Mount Control Unit at
a convenient height
for access to display
and controls
CerberusTM
FC2005/FC901 installation instruction
Document ID: A5Q00039713A
Page 5/12 02.2012
Fire Safety & Security Products
Building Technologies FC2005/FC901 installation instruction

Installation instruction with Trim kit
21 1/4”
4 1/4” MAX
19 5/8”
8 1/4”
Mount Control Unit at
a convenient height
for access to display
and controls
CerberusTM
FC2005/FC901 installation instruction
Document ID: A5Q00039713A
Page 6/12 02.2012
Fire Safety & Security Products
Building Technologies FC2005/FC901 installation instruction

FC2005/FC901 SYSTEM CONNECTION DIAGRAM
Environm ental SLC Addressable Device Circuits
Operating temperature - 32 - 120°F (0 - 49°C) 32 VDC Max
Relative humidity - Up to 93% @ 90°F (32°C) Pow er limited
To be installed in a indoor dry protected environment only Supervised
Max. current: 0.07A(RMS)
Prim ary Pow er Supply Maximum w ire loop resistance: 50Ω
Input: 120VAC, 60 Hz or 220 VAC, 50 Hz Tw o Style 4 Class B or one Style 6 Class A circuit
@ 2.0A Max. Max. 50 addressable devices
Supervised City Tie Circuits
Output: 26VDC @ 6.5A Max. Supply Input:
Max current: 6.5A (2 hours Max.) Voltage: 26 VDC
Filtered and Regulated 18 – 28 VDC for battery
Current: Max. 0.4A
Secondary Pow er Supply Supervised
24V lead-acid battery set Output:
Max. charged voltage: 27.8 VDC City Tie-Output 1
Automatic low battery disconnect voltage: 19.2±0.1VDC Normal output voltage: 19-28VDC (open circuit condition)
Max. charge current: 0.45A Supervisory current: 1mA
Battery capacity:12AH to 18AH Maximum trip current: 400mA
Supervised Maximum coil plus w ire resistance: 22.5Ω
Auxiliary Pow er Outputs Leased line-Output 1
- Non-resettable pow er output Normal output voltage:19-28VDC (open circuit condition)
Pow er limited Trouble output voltage: 0V
Alarm status: 0.75A
Alarm output voltage:-(19-28)VDC (open circuit condition)
Normal stand by: 0.05A Maximum w ire resistance: 2-5KΩ
Voltage: 19 to 28VDC Maximum short circuit current: 25mA
Ripple: 0.1 VAC
Special Application Leased line-Output 2
Normal output voltage: 19-28VDC (open circuit condition)
- Resettable pow er output Supervisory output voltage: -(19-28)VDC (open circuit condition)
Pow er limited Maximum w ire resistance: 2-5KΩ
Alarm status: 0.75A Maximum short circuit current: 25mA
Normal stand by: 0.05A
Voltage: 19 to 28VDC DACT Circuits
Ripple: 0.1 VAC Pow er limited
Special Application Supervised for short or open circuit conditions
Compliance to FCC part 68
Status Relays Support RJ31X connection
Non-pow er limited Compatible Digital Alarm Communication Receiver (DACR) list,
One programmable relay
Three non-programmable relays: Trouble, Supervisory, Alarm
Contact rating: 2A, 30VDC maximum
Form C contact
Notification Appliance Circuits
Pow er limited
Supervised
Current Draw Maximum Line Resistance
2.5A 3.2Ω
2.0A 4.0Ω
1.5A 5.3Ω
1.0A 8.0Ω
0.5A 16.0Ω
Alarm voltage: 16 to 32VDC
Maximum ripple: 0.1VAC
Used for special application only
Tw o Style Y/Class B or one Style Z/Class A
Total Max. Current: 2.5A
Device m odule Manufacture
MX8000 Honeyw ell
DACT compatibility list
CAUTION – To reduce the risk of fire, use only No. 26 AWG
or larger telecommunication line cord.
FC2005/FC901 SYSTEM GENERAL SPECIFICATION
Document ID: A5Q00039713A
Page 7/12 02.2012
Fire Safety & Security Products
Building Technologies FC2005/FC901 installation instruction

FC2005/FC901 SYSTEM CONNECTION DIAGRAM
FC2005/FC901 SYSTEM CONNECTION DIAGRAM
EARTH
S_BN
S_BP
EARTH
S_AN
S_AP
X2_P
X2_N
X1_P
X1_N
EARTH
SE_B
SE_A
GND1
EARTH
PR_B
PR_A
GND1
CT_P
CT_N
LL_SP
LL_SN
N_BP
N_BN
N_AP
N_AN
DACT
PORT1
DACT
PORT2
S_NO
S_CO
S_NC
U_NO
U_CO
U_NC
A_NO
A_CO
A_NC
T_NC
T_CO
T_NO
Battery connector
12AH - 18AH@24VDC
Supervised, Non power limited
USB type B plug
DC power input
6.5A@26VDC
SLC loop Auxiliary power Series interface circuit
City tie or
lease line
Notification Application
Circuits(NAC) DACT Relays
Note: All the wiring must be in according with local codes and National Electric Code.
Document ID: A5Q00039713A
Page 8/12 02.2012
Fire Safety & Security Products
Building Technologies FC2005/FC901 installation instruction

FC2005/FC901 SYSTEM CONNECTION DIAGRAM
FC2005/FC901 SYSTEM CONNECTION DIAGRAM
SLC loop connections
Supervised and power limited, detail device compatibility list refer to user manual Appendix B
Auxiliary power
Non supervised and power limited
Class A
...
50 max devices
0.07A@6-32 VDC
Note: The earth gets connected to the
shield (if used)
EARTH S_BN S_BP EARTH S_AN S_AP EARTH S_BN S_BP EARTH S_AN S_AP 0.07A@6-32 VDC
50 max devices
... ...
0.07A@6-32 VDC
Class B
Note: The earth gets connected
to the shield (if used)
X2_P X2_N X1_P X1_N
Conventional detectors
Alarm 0.75A @19-28VDC
Normal 0.05A @19-28VDC
Auxiliary power output 2
(Resettable, power limited)
Power -
Power +
Alarm 0.75A @19-28VDC
Normal 0.05A @19-28VDC
Auxiliary power output 1
(Non-resettable, power limited)
+-+-
Max. current= 0.75A Max. current= 0.75A
24V
applicance
Document ID: A5Q00039713A
Page 9/12 02.2012
Fire Safety & Security Products
Building Technologies FC2005/FC901 installation instruction