Siemens IM 328-N Operating and installation instructions

SINUMERIK 805SM/840C
Link to SINEC L2–DP
with IM 328–N Module
Description 07.96 Edition
Manufacturer Documentation

07.96 Edition
SINUMERIK 805SM/840C
Link to SINEC L2–DP
with IM 328–N Module
Description
Manufacturer Documentation
General 1
Hardware 2
Configuring the Modules 3
Abbreviations A
References B
Index C

SINUMERIKdocumentation
Printing history
Brief details of this edition and previous editions are listed below.
The status of each edition is shown by the code in the “Remarks” column.
Status code in the “Remarks” column.
ANew documentation.. . . .
BUnrevised reprint with new Order No.. . . .
CRevised edition with new status.. . . . If factual changes have been made on the page since the last edition, this is
indicated by a new edition coding in the header on that page.
Edition Order No. Remarks
08.93 6ZB5 430–0BH02–0AA0 A
11.94 6ZB5 430–0BH02–0AN0 Supplement
07.96 6ZB5 430–0BH02–1AA0 A
Siemens quality for software and training
to DIN ISO 9001, Reg. No. 2160–01
This publication was produced with Interleaf V 5.3
The reproduction, transmission or use of this document or its
contents is not permitted without express written authority.
Offenders will be liable for damages. All rights, including rights
created by patent grant or registration of a utility model or
design, are reserved.
Siemens AG 1996. All rights reserved.
Other functions not described in this documentation might be
executable in the control. This does not, however, represent an
obligation to supply such functions with a new control or when
servicing.
We have checked that the contents of this publication agree with the
hardware and software described herein. The information given in this
publication is reviewed at regular intervals and any corrections that
might be necessary are made in the subsequent printings.
Suggestions for improvement are welcome at all times.
Subject to change without prior notice.
Siemens–Aktiengesellschaft
Order No. 6ZB5 430–0BH02–1AA0
Printed in the Federal Republic of Germany
1
Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0
SINUMERIK 805SM / 840C (BS)
3ls

07.96 Description
i
Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0
SINUMERIK 805SM / 840C (BS)
PRELIMINARY REMARKS
Notes to the reader
This description is aimed at machine manufacturers and service personnel
and describes the use of the IM 328–N module in SINUMERIK and SIRO-
TEC as a slave in the ET 200 Distributed I/O System.
This manual provides information on
jumper settings on the module as well as interfaces and operating
elements
data required for configuring the module
installation and startup of the module
error messages and application examples
Note
The description of the ET 200 Distributed I/O System is to be found in:
Reference: /1/, ET 200 Distributed I/O System Manual
For the distributed I/O systems ET 200U, ET 200B and ET 200C etc. the
following separate manuals are available:
Reference: /2/, Distributed I/O System Manual
This description contains the information required for start–up and service.
A page for your corrections and suggestions is provided at the end of this
manual. Please fill in this form and send it back to us. This will help us to
improve the next edition.
So that you can find the information you need, this document not only con-
tains a table of contents, a list of figures and a list of tables, but in the appen-
dix you will also find:
1. A list of abbreviations
2. A list of references
3. An index
Target group
Contents
Objective
Corrections/
suggestions
Searching aids

07.96Description
ii 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved
SINUMERIK 805SM / 840C (BS)
Note
Text marked in this way is important information to which the reader must
pay special attention.
!Important
This symbol appears in documents wherever important information is given.
Ordering data option
This symbol indicates functions for which an ordering data option is required
(options). The function described can only be executed if the option designa-
ted is present.

07.96 Description
iii
Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0
SINUMERIK 805SM / 840C (BS)
Safety notes
!Warning
When electrical devices are in operation, certain parts of them are inevitably
subjected to hazardous voltages.
Improper interference with the device/system or failure to observe the
warning advice can result in serious physical injury or material damage.
Only appropriately trained personnel familiar with the assembly, installa-
tion, starting up or operation of the product are permitted to interfere with
this device/sytem.
!Warning
Qualified persons as referred to in the safety guidelines (in the documenta-
tion or affixed to the product itself) are persons who, for instance:
Have received training or instruction and authorization to energize and
de-energize, ground and tag electric circuits and equipment in accor-
dance with established safety practices.
Have received training or instruction in accordance with established
safety practices in the care, use and repair of appropriate safety
equipment.
Have received training or instruction in working with electrostatically
sensitive components or modules.
Have been instructed as operators to work with automation technology
equipment and are familiar with the contents in the Operator’s and/or
Programming Guide referring to operation.
Note
When planning, installing, starting up and operating the control, personnel
concerned must be familiar with the documentation relevant to their jobs.
Qualified
personnel

07.96Description
iv 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved
SINUMERIK 805SM / 840C (BS)
Danger notices
The notices and guidelines that follow are intended to ensure personal safety
and to protect the product described here or connected devices and machines
against damage.
The safety notices and guidelines intended to avert danger to human life and
health and to avoid material damage are emphasized in this Manual by the
terms defined below. The terms have the following meanings in the context
of this Manual and the notices on the product itself:
!Danger
This symbol means that death, serious injury or considerable material da-
mage will occur, if the precautionary measures indicated are not taken.
!Caution
indicates that personal injury or property damage can result if proper pre-
cautions are not taken.
!Warning
indicates that death, severe personal injury or substantial property damage
can result if proper precautions are not taken.
Intended use
The device/system or system component must be used only for the
applications specified in the Catalog and Reference Manual and only in
conjunction with such non-Siemens devices and components as have been
recommended and approved by Siemens.
The product described in the manual has been developed, manufactured,
tested and documented in compliance with the relevant safety standards.
Provided the handling instructions and safety guidelines described for
planning, assembling, proper operation and maintenance are observed, the
product will not normally be a source of danger leading to material
damage or physical injury.

07.96 Description
v
Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0
SINUMERIK 805SM / 840C (BS)
Notes on product planning
As the product is generally part of larger systems or plants, these notes are
intended as a guideline for safe integration of a product in its environment.
Note the following in particular:
Note
Even when a maximum of safety has been included in the design of automa-
tion equipment, e.g. by means of a multi-channel configuration, the instruc-
tions given in the documentation must be followed exactly because incorrect
handling can render ineffective the preventive measures incorporated to
protect against dangerous faults or create new sources of danger.
Active and passive faults in automation equipment
Depending on the paricular task for which the electronic automation
equipment is used, both active and passive faults can be dangerous
faults. In the case of a drive control, for example, active faults are ge-
nerally dangerous because they lead to unauthorized startup of the drive.
On the other hand, a passive fault can result in a dangerous operating state
not being reported to the operator.
This differentiation between possible faults and their task-related classifi-
cation as dangerous and non-dangerous faults is important for all the
safety considerations in respect of the product supplied.
!Warning
Wherever a fault in the automation equipment can cause serious material
damage or even physical injury, in other words wherever dangerous faults
can occur, additional external precautions must be taken or devices provided
which will insure or enforce safe operating conditions even in the event of a
fault (e.g. by means of independent limit switches, mechanical interlocks
etc.).
Note
The information contained in this documentation is checked and updated
regularly and can be changed at any time without further notice.

07.96Description
vi 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved
SINUMERIK 805SM / 840C (BS)
Technical notes
Before start–up, please set the assignments on the module and on the front
panel as required for the application or check that they are set.
The IM 328–N module can be operated as a slave in the ET 200 Distributed
I/O System.
From the point of view of the control, the module responds like an I/O mo-
dule.
The modules
IM 328–N, Slave, MLFB: 6FC5 012–0CA03–0AA0 (IM 328–N, new)
IM 328–N, Slave, MLFB: 6FC5 012–0CA01–0AA0 (IM 328–N, old), and
IM 329–N, Slave, MLFB: 6FC5 012–0CA02–0AA0 (master and slave)
have different applications as follows:
Table 1-1 Different applications between IM 328–N and IM329–N
Module
Use as IM 328–N
(... 0CA03 ...) IM 328–N (... 0CA01 ...) IM 329–N, Slave (... 0CA02 ...)
Slave
for SINEC L2–DP to
V3.x
X X
Slave
for SINEC L2–DP
(PROFIBUS–DP,
acc. to DIN E 19245,
part 3)
X X
Master X
For information on the IM 329–N see:
Reference: /7/, Description
Link to SINEC L2–DP with IM 329–N Module
SIMATIC, SINECand SINUMERIKare registered trademarks of
SIEMENS AG.
Checking the
assignments
Operating the
module
Response of the
module
Difference between
the IM 328–N and
IM 329–N modules
Trademarks

07.96 Description
vii
Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0
SINUMERIK 805SM / 840C (BS)
Contents
1 General 1-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 Hardware 2-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1 Hardware of the module 6FC5 012–0CA03–0AA0 2-1. . . . . . . . . . . . . . . .
2.1.1 Jumper settings 2-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1.2 Elements on the front plate 2-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1.3 Technical data 2-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2 Hardware of the module 6FC5 012–0CA01–0AA0 2-9. . . . . . . . . . . . . . . .
2.2.1 Jumper settings 2-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.2 Elements on the front plate 2-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.3 Technical data 2-16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 Configuring the Modules 3-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1 COM ET 200 parameterization software 3-1. . . . . . . . . . . . . . . . . . . . . . . . .
3.1.1 Installation 3-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1.2 COM ET 200 parameterization software 3-2. . . . . . . . . . . . . . . . . . . . . . . . .
3.2 Description of the DP standard slaves 3-5. . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.1 Notes on parameterization of the slaves 3-5. . . . . . . . . . . . . . . . . . . . . . . . .
3.2.2 Configuration example for slave 3-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.3 Procedure for Installation and Startup 3-8. . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.4 Example of Application 3-9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.5 Status display messages 3-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.6 Diagnostics functions in the S5 program of the master 3-16. . . . . . . . . . . . .
3.3 Description of the L2-DP slave up to V3.x 3-22. . . . . . . . . . . . . . . . . . . . . . . .
3.3.1 Notes on parameterization of the slaves 3-22. . . . . . . . . . . . . . . . . . . . . . . . .
3.3.2 Configuration example 3-24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.3 Procedure for installation and startup 3-25. . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.4 Fault during data transmission 3-26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.5 Messages via status display 3-27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.6 Diagnostics functions in the S5 program of the master 3-28. . . . . . . . . . . . .
A Abbreviations A-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B References B-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C Index Index-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1
07.96 Description
1-1
Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0
SINUMERIK 805SM / 840C (BS)
General
The SINEC L2-DP field bus is a distributed I/O version of the SINEC L2 and
is designed for minimum response times in the communication with distribu-
ted I/O devices.
The ET 200 distributed I/O system for SIMATIC S5 uses the SINEC L2-DP
field bus. The system is based on the PROFIBUS-DP communications
standard (DIN E 19245, Part 3) and works on the master/slave principle.
The following devices can be master stations:
+
ÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉ
SIMATIC S5
115U
135U
155U
with IM 308–B
IM 308–C interface
Programming device
PG 730, PG 750 or PG 770
with CP 5410–S5DOS/ST
interface
SINUMERIK
or
SIROTEC
SINUMERIK 805SM
SINUMERIK 840C
SIROTEC ACR 20
with module IM 329–N, master
or other master stations with PROFIBUS–DP
Fig. 1-1 Master stations
SINEC L2–DP
Field bus
Distributed I/O
system ET 200
Master stations
1 General
1

1
07.96Description
1-2 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved
SINUMERIK 805SM / 840C (BS)
The following devices can be slave stations:
SINUMERIK
or
SIROTEC
SINUMERIK 805SM
SINUMERIK 840C
SIROTEC ACR 20
with module IM 328–N
Distributed I/O devices
e.g.
ET 200B
ET 200U
ET 200C
S5–95U–DP
or other PROFIBUS–DP slaves
Fig. 1-2 Slave stations
The diagram below gives an example of how to connect the master and slave
stations to the SINEC L2-DP field bus:
SINUMERIK
or
SIROTEC
ET 200
SINEC L2–DP field bus
SIMATIC
S5–155U
CP 5410–B interface module
Master IM 308–B interface module
Slaves
IM 328–N interface module
(SINEC L2–DP slave module)
ET 200 ET 200 ET 200ET 200
Programming device
Fig. 1-3 Using the module IM 328-N as a slave
J
Slave stations
Example
1 General

2
07.96 Description
2-1
Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0
SINUMERIK 805SM / 840C (BS)
Hardware
2.1 Hardware of the module 6FC5 012–0CA03–0AA0
SPC
Dual
port
RAM
(DPR)
FEPROM
Quarz Quarz
Bus connector
DC/DC
converter
Slave
S3. 1
8
ON S2. 1
8
ON
Interface
Interface X112
and LEDs have
no function if
they exist
Station
address
for slave
Units place
100
Tens place
Hundreds place
101
100–199
0–99
FAULT
(red LED)
RUN
(green LED)
X21
3
5
3
5
Status display
Slave
X112
X111
X999
Switch position
always down
µP
Fig. 2-1 Module IM 328–N with the order number: 6FC5 012–0CA03–0AA0
2.1 Hardware of the module 6FC5 012–0CA03–0AA0
2

2
07.96Description
2-2 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved
SINUMERIK 805SM / 840C (BS)
2.1.1 Jumper settings
The module can be used in the control systems listed. The control type must
be set with switches S2.5, S2.6, S2.7 and S2.8 as follows:
S2.5 S2.6 S2.7 S2.8
SINUMERIK 805SM OFF ON OFF ON
SIROTEC ACR 20 ON ON ON ON
SINUMERIK 840C ON ON ON ON
Note
The IM 328–N module can only be used for SINUMERIK 805SM in the
central controller.
Switches S2.1 and S2.2 must be set according to the table below in order to
set the address range of 4, 8, 16 or 32 input or output bytes.
Address range S2.1 in position S2.2 in position
4 bytes OFF OFF
8 bytes OFF ON
16 bytes ON OFF
32 bytes ON ON
Note
Address range of, for example, 4 bytes means that 4 input bytes and 4 output
bytes are available with the same base address.
The following switches are used to set the module numbers (base address)
S3.1 to S3.8 for an address range of 4 bytes
S3.2 to S3.8 for an address range of 8 bytes
S3.3 to S3.8 for an address range of 16 bytes
S3.4 to S3.8 for an address range of 32 bytes
Selecting the
control system
(S2.5, S2.6, S2.7
and S2.8)
Setting of address
range (number of
input and output
bytes) (S2.1 and
S2.2)
Setting the base
address
(S3.1 to S3.8)
2.1 Hardware of the module 6FC5 012–0CA03–0AA0

2
07.96 Description
2-3
Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0
SINUMERIK 805SM / 840C (BS)
Note
The switches not required for the 8, 16 and 32-byte address ranges are irrele-
vant and any setting is permissible.
Switch S2.1 = OFF and S2.2 = OFF
Baseaddress S3.8 S3.7 S3.6 S3.5 S3.4 S3.3 S3.2 S3.1
0 ON ON ON ON ON ON ON ON
4 ON ON ON ON ON ON ON OFF
8 ON ON ON ON ON ON OFF ON
12 ON ON ON ON ON ON OFF OFF
16 ON ON ON ON ON OFF ON ON
: : : : : : : : :
1020 OFF OFF OFF OFF OFF OFF OFF OFF
Significance 29
=512 28 =256 27 =128 26 =64 25 =32 24 =16 23 =8 22 =4
Switch S2.1 = OFF and S2.2 = ON
Baseaddress S3.8 S3.7 S3.6 S3.5 S3.4 S3.3 S3.2 S3.1
0 ON ON ON ON ON ON ON x
8 ON ON ON ON ON ON OFF x
16 ON ON ON ON ON OFF ON x
24 ON ON ON ON ON OFF OFF x
32 ON ON ON ON OFF ON ON x
: : : : : : : :
1016 OFF OFF OFF OFF OFF OFF OFF x
Significance 29
=512 28 =256 27 =128 26 =64 25 =32 24 =16 23 =8
x: Switch position of no significance
Base address for
4–byte address range
Base address for
8–byte address range
2.1 Hardware of the module 6FC5 012–0CA03–0AA0

2
07.96Description
2-4 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved
SINUMERIK 805SM / 840C (BS)
Switch S2.1 = ON and S2.2 = OFF
Baseaddress S3.8 S3.7 S3.6 S3.5 S3.4 S3.3 S3.2 S3.1
0 ON ON ON ON ON ON x x
16 ON ON ON ON ON OFF x x
32 ON ON ON ON OFF ON x x
48 ON ON ON ON OFF OFF x x
54 ON ON ON OFF ON ON x x
: : : : : : :
1008 OFF OFF OFF OFF OFF OFF x x
Significance 29
=512 28 =256 27 =128 26 =64 25 =32 24 =16
x: Switch position of no significance
Switch S2.1 = ON and S2.2 = ON
Baseaddress S3.8 S3.7 S3.6 S3.5 S3.4 S3.3 S3.2 S3.1
0 ON ON ON ON ON x x x
32 ON ON ON ON OFF x x x
64 ON ON ON OFF ON x x x
96 ON ON ON OFF OFF x x x
: : : : : :
992 OFF OFF OFF OFF OFF x x x
Significance 29
=512 28 =256 27 =128 26 =64 25 =32
x: Switch position of no significance
Note
Base addresses are only possible for 4-byte, 8-byte, 16-byte or 32-byte steps
depending on the address range. For example, an address range of 32 bytes
permits only 0, 32, 64, 96 etc. as initial addresses.
Address range = 8 bytes and the base address is to be 24 ⇒
S2.1 = OFF and S2.2 = ON
S3.8, S3.7, S3.6, S3.5, S3.4 = ON and S3.3, S3.2 = OFF
The assigned input and output area is from IB 24/QB 24 to IB 31/QB 31.
Base address for
16–byte address range
Base address for
32–byte address range
Example of address
setting
2.1 Hardware of the module 6FC5 012–0CA03–0AA0

2
07.96 Description
2-5
Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0
SINUMERIK 805SM / 840C (BS)
!Danger
An incorrect setting of the base address (e.g. dual address assignment or
address conflict with other I/O modules) results in “wrong signal states” and
can cause an undefined behaviour of the control and the machine!
These switches are assigned as follows:
Switch Position
2.3 ON
2.4 OFF
With this jumper you can set the type of communication with which the mo-
dule is to be operated.
Table 3-1 Setting for the type of communication
X999 Meaning
Module is operated as a SINEC L2–DP slave (standard DP)
(see Section 3.2).
Module is operated as a SINEC L2–DP slave up to V 3.x
(see Section 3.3).
The module behaves like the 6FC5 012–0CA01–0AA0 module.
In assigning the slaves, please note that the following I/O ranges are availa-
ble on the SIROTEC ACR 20, SINUMERIK 805SM and SINUMERIK 840C
controls:
SINUMERIK
805SM (SW4) SIROTEC ACR 20 (SW5) SINUMERIK 840C (SW4)
Inputs IB 0 to IB 47 I 1 to I 1024
(IB 0 to IB 127) IB 0 to IB 127
Outputs QB 0 to QB 47 Q 1 to Q 1024
(QB 0 to QB 127) QB 0 to QB 127
Physical
interface
without process
image
– – PB 0 to PB 255
For the allocation of the I/O range for each control see:
Switches S2.3
and S2.4
Jumper
X999
I/O ranges
2.1 Hardware of the module 6FC5 012–0CA03–0AA0

2
07.96Description
2-6 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved
SINUMERIK 805SM / 840C (BS)
Reference: /3/, SINUMERIK 805SM, –TW,
Interface Description, Part 2 – Connection Conditions
Reference: /4/, SIROTEC ACR 20, Configuration Instructions
Note
The I/O range must be addressed without gaps with SIROTEC ACR 20
Reference: /5/, SINUMERIK 840C
Interface Description, Part 2 – Connection Conditions
2.1 Hardware of the module 6FC5 012–0CA03–0AA0

2
07.96 Description
2-7
Siemens AG 1996 All Rights Reserved 6ZB5 430–0BH02–1AA0
SINUMERIK 805SM / 840C (BS)
2.1.2 Elements on the front plate
The rotary switch is used to set the units place (first switch from top) and the
tens place (second switch from top) of the station address.
The hundreds place of the station address depends on the setting of the toggle
switch (upper position = 1 x 100, lower position = 0 x 100). Valid station ad-
dresses are between 3 and 124.
Note
The software limits the station address to the range from 3 to 124.
A change in station address does not become active until after a restart of
the control.
The status display (FAULT and RUN LED) can indicate the following states
of the SINEC L2-DP slave module.
RUN
(green LED) FAULT (red LED) Remark
off on The module is being initialized
(this state lasts for a short period of time only)
on off Normal operating state, slave in cyclic operation
other states Fault
(for L2–DP, DP standard, see Section 3.2.5)
(for L2–DP to V3.x see Section 3.3.5)
Via the interface X111 (SUB–D, socket, 9–way), the slave is connected to the
SINEC L2–DP field bus.
Note
To connect up to the SINEC L2–DP field bus, the bus connectors with the
following order numbers are required:
Order number Designation
6ES5 762–2AA12 SINEC L2 bus connector (degree of protection IP 20, without
heavy–duty thread socket)
6ES5 762–2AA21 SINEC L2 bus connector (degree of protection IP 20, with
heavy–duty thread socket)
For information about the bus cable and the bus connector see:
Reference: /1/, ET 200 Distributed I/O System Manual
Station address
Status display of
the slave (LEDs)
Interface for slave
2.1 Hardware of the module 6FC5 012–0CA03–0AA0

2
07.96Description
2-8 6ZB5 430–0BH02–1AA0 Siemens AG 1996 All Rights Reserved
SINUMERIK 805SM / 840C (BS)
2.1.3 Technical data
6FC5 012–0CA03–0AA0
Type Value
PCB format Double-height Eurocard format
(160 x 233.4 mm)
Width of front panel 1 1/3SPS, metal (1 SPS = 15.24 mm)
Front connector 9–pin, SUB–D female connector
(bus interfaces)
Degree of protection IP 00 to DIN 40050
Permissible ambient temperature
during operation 0 to + 55 °C
Transport and storage temperature – 40 to + 70 °C
Humidity class F to DIN 40040
Shock resistance Class 12 to SN 29010
Mass 340 g
Power supply + 5 V (+/– 5%), 1.1 Amax
Order No.
2.1 Hardware of the module 6FC5 012–0CA03–0AA0