Siemens SIPROTEC4 7SJ61 User manual

SIPROTEC4
Multifunction protection with
control
7SJ61...63, 7SJ65
Input/Output unit with local
control
6MD63
Communication module
PROFIBUS-DP
Bus mapping
Revision: 2.1
Edition: October 2001
C53000-L1840-B006-02
Preface
Data in the PROFIBUS-DP
messages 1
Standard mapping 2-1 2
Standard mapping 2-2 3
Standard mapping 2-3 4
Standard mapping 2-4 5
Glossary
Index
Cover

Non-liability clause Copyright
Although we have checked the contents of this publication for
conformance with the hardware and software described we
cannot guarantee complete conformance since differences
cannot be ruled out.
The information in this manual is checked at regular intervals,
and necessary corrections are included in the next releases.
Your suggestions are welcome.
Subject to change without prior notice.
Copyright ãSiemens AG 2001. All rights reserved.
Passing on or reproduction of this document, utilization and revelation
of its contents is not permitted without express permission.
Violations shall be cause for damage claims.
All rights reserved, in particular when a patent is issued or a general
model registered.
Registered trademarks
SIPROTECâund DIGSIâare registered trademarks of Siemens AG.
Other designations in this manual may be trademarks that if used by
third parties for their own purposes may violate the rights of the owner.
Siemens Aktiengesellschaft C53000-L1840-B006-02

7SJ61...7SJ63, 7SJ65, 6MD63 PROFIBUS-DP – Bus mapping
C53000-L1840-B006-02 i
Preface
Contents of this
manual The manual is devided into the following topics:
•Data in the PROFIBUS-DP messages
•Standard mapping 2-1
•Standard mapping 2-2
•Standard mapping 2-3
•Standard mapping 2-4
Additional
literature This manual describes the data in the PROFIBUS-DP messages of the
SIPROTEC devices 7SJ61...7SJ63, 7SJ65, 6MD63.
The following additional manuals inform you about the data types, bus
specific parameters and hardware description of the PROFIBUS-DP
slave modul and the function, operation, assembly and commissioning
of the SIPROTEC devices:
Manual Contents Order number
Overcurrent, overload and
motor protection with control
SIPROTEC 7SJ61
Function, operation, assembly
and commissioning of the
SIPROTEC device 7SJ61 C53000-G1140-C118-2
Multifunction protection with
control
SIPROTEC 7SJ62
Function, operation, assembly
and commissioning of the
SIPROTEC device 7SJ62 C53000-G1140-C121-2
Multifunction protection with
control
SIPROTEC 7SJ63
Function, operation, assembly
and commissioning of the
SIPROTEC device 7SJ63 C53000-G1140-C120-2
Multifunction protection with
control and small-signal
interface
SIPROTEC 7SJ65
Function, operation, assembly
and commissioning of the
SIPROTEC device 7SJ65 C53000-G1140-C144-1
Input/output unit with local
control
SIPROTEC 6MD63
Function, operation, assembly
and commissioning of the
SIPROTEC device 6MD63 C53000-C1840-C101-2
7SJ61...63, 7SJ65, 6MD63,
7UM61 PROFIBUS-DP -
Communication profile
Data types, bus specific para-
meters and hardware descrip-
tion of the PROFIBUS-DP slave
modul of the SIPROTEC
devices
C53000-L1840-B001-02

Preface
7SJ61...7SJ63, 7SJ65, 6MD63 PROFIBUS-DP – Bus mapping
C53000-L1840-B006-02
ii
The PROFIBUS-DP specification and the structure of the PROFIBUS-
DP messages are defined in the European standard EN 50170:
ØPROFIBUS Specification
Normative Parts of PROFIBUS-FMS, -DP., -PA
According to the European Standard
EN 50170 Volume 2
Edition 1.0, May 1998
PROFIBUS Nutzerorganisation e.V.
Order-No. 0.032 or 0.042 on CD ROM
Notes to this
manual This manual provides you with the following aids to make it easier to
locate the information you are looking for:
•At the beginning of this manual you will find a complete table of
contents plus separate lists of figures and tables contained in this
manual.
•In the individual chapters, you will find information in the left margin
of each page which will give you an overview of the contents of that
particular paragraph.
•Following the last chapter of this manual, you will find a glossary
containing definitions of technical terms and abbreviations used in
this manual.
•At the end of this manual, you will find a comprehensive index for
fast access to the information you need.
Validity This manual is valid for
•SIPROTEC devices 7SJ61...7SJ63, 7SJ65, 6MD63 with:
•firmware version 4.2 or higher (7SJ65: version 4.3 or higher)
and
•PROFIBUS-DP communication module version 01.01.02 or
higher.
For device parameterization DIGSI version 4.2 or higher has to be
used.
Training courses See our catalog of courses for a list of available courses or contact our
Training center in Nuremberg.
Questions If you have questions to the SIPROTEC devices, contact your Siemens
representative.

7SJ61...7SJ63, 7SJ65, 6MD63 PROFIBUS-DP – Bus mapping
C53000-L1840-B006-02 iii
Revision index
Modified chapters /
pages Edition Reasons of modification
1.0 First edition, Doc.-No.: C53000-L1840-B006-02
Aug 23rd, 2000
chap. 4.2.3.1
chap. 5
chap. 1.6
chap. 1.5.5
2.0 •Document also valid for 7SJ65 devices
•Allocation 3/0...3/7 for Standard mapping 2-3 corrected
•Standard mapping 2-4 added
•Chap. "Using device firmware version 4.3 or higher" added
•Description of "Error with a summary alarm" extended
Feb 22nd, 2001
chap. 1.4
chap. 4.2.3
chap. 2.1.3, 3.1.3
2.1 •Parameterization of the PROFIBUS-DP master: Order number of the
output module for standard mapping 2-3 corrected
•Offsets of metered measurands in Standard mapping 2-3 corrected
•Internal object no. for activation/deactivation of Automatic recloser
and Protection functions changed
Oct 31st , 2001

Revision index
7SJ61...7SJ63, 7SJ65, 6MD63 PROFIBUS-DP – Bus mapping
C53000-L1840-B006-02
iv

7SJ61...7SJ63, 7SJ65, 6MD63 PROFIBUS-DP – Bus mapping
C53000-L1840-B006-02 v
Table of contents
1 Data in the PROFIBUS-DP messages........................................................................... 1-1
1.1 Explanation..................................................................................................... 1-1
1.2 Messages in output direction: PROFIBUS-DP master to the SIPROTEC
device............................................................................................................. 1-3
1.3 Messages in input direction: SIPROTEC device to the PROFIBUS-DP
master............................................................................................................ 1-3
1.3.1 Annunciations................................................................................................. 1-3
1.3.2 Measured values............................................................................................ 1-4
1.3.3 Metered measurands..................................................................................... 1-5
1.4 Configuration data of the standard mappings 2-1 to 2-4................................ 1-6
1.5 Notes to SIPROTEC objects........................................................................ 1-10
1.5.1 Single commands......................................................................................... 1-10
1.5.2 Control mode REMOTE............................................................................... 1-11
1.5.3 Changing the setting group.......................................................................... 1-11
1.5.4 CFC-Incoming annunciations....................................................................... 1-12
1.5.5 Error with a summary alarm......................................................................... 1-12
1.5.6 Alarm summary event.................................................................................. 1-13
1.5.7 Stop data transmission................................................................................. 1-13
1.5.8 Fault locator: Fault location.......................................................................... 1-13
1.6 Using device firmware version 4.3 or higher................................................ 1-14
2 Standard mapping 2-1 ................................................................................................... 2-1
2.1 Message in output direction ........................................................................... 2-1
2.1.1 Double commands (with checkback indication)............................................. 2-1
2.1.2 Single commands (without checkback indication) ......................................... 2-1
2.1.3 Internal commands ........................................................................................ 2-2
2.1.4 Application logic CFC..................................................................................... 2-2
2.2 Message in input direction ............................................................................. 2-4
2.2.1 Annunciations................................................................................................. 2-4
2.2.1.1 Double commands – checkback signals.....................................................................2-4
2.2.1.2 Single commands – status..........................................................................................2-4
2.2.1.3 Input channels with allocation to the binary inputs and tagging..................................2-4
2.2.1.4 Application logic CFC..................................................................................................2-5

Table of contents
7SJ61...7SJ63, 7SJ65, 6MD63 PROFIBUS-DP – Bus mapping
C53000-L1840-B006-02
vi
2.2.1.5 Diagnosis.....................................................................................................................2-5
2.2.1.6 Automatic recloser status............................................................................................2-6
2.2.1.7 Time overcurrent protection.........................................................................................2-6
2.2.1.8 Directional time overcurrent protection........................................................................2-7
2.2.1.9 Unbalanced load protection.........................................................................................2-7
2.2.1.10 Frequency protection ..................................................................................................2-7
2.2.1.11 Undervoltage and overvoltage protection ...................................................................2-8
2.2.1.12 Sensitive ground fault protection.................................................................................2-8
2.2.1.13 Circuit breaker failure protection.................................................................................2-8
2.2.1.14 Thermal overload protection .......................................................................................2-9
2.2.1.15 Motor start protection..................................................................................................2-9
2.2.1.16 Startup supervision .....................................................................................................2-9
2.2.1.17 Trip coil monitor...........................................................................................................2-9
2.2.1.18 Cold load pickup setup................................................................................................2-9
2.2.1.19 Measurement supervision.........................................................................................2-10
2.2.1.20 Set point alarms........................................................................................................2-10
2.2.1.21 Status annunciations.................................................................................................2-10
2.2.2 Measured values.......................................................................................... 2-11
2.2.2.1 Recorded measured values.......................................................................................2-11
2.2.2.2 Measured values – mean values...............................................................................2-11
2.2.3 Fault locator..................................................................................................2-12
2.2.4 Metered measurands................................................................................... 2-12
3 Standard mapping 2-2 ...................................................................................................3-1
3.1 Message in output direction ...........................................................................3-1
3.1.1 Double commands (with checkback indication)............................................. 3-1
3.1.2 Single commands (without checkback indication) .........................................3-1
3.1.3 Internal commands......................................................................................... 3-2
3.1.4 Application logic CFC..................................................................................... 3-2
3.2 Message in input direction.............................................................................. 3-4
3.2.1 Annunciations................................................................................................. 3-4
3.2.1.1 Double commands – checkback signals.....................................................................3-4
3.2.1.2 Single commands – status ..........................................................................................3-4
3.2.1.3 Input channels with allocation to the binary inputs and tagging ..................................3-4
3.2.1.4 Application logic CFC..................................................................................................3-5
3.2.1.5 Diagnosis.....................................................................................................................3-5
3.2.1.6 Automatic recloser status............................................................................................3-6
3.2.1.7 Time overcurrent protection.........................................................................................3-6
3.2.1.8 Unbalanced load protection.........................................................................................3-7
3.2.1.9 Sensitive ground fault protection.................................................................................3-7
3.2.1.10 Circuit breaker failure protection.................................................................................3-7
3.2.1.11 Thermal overload protection .......................................................................................3-7
3.2.1.12 Motor start protection..................................................................................................3-7
3.2.1.13 Startup supervision .....................................................................................................3-7
3.2.1.14 Trip coil monitor...........................................................................................................3-8

7SJ61...7SJ63, 7SJ65, 6MD63 PROFIBUS-DP – Bus mapping
C53000-L1840-B006-02 vii
3.2.1.15 Cold load pickup.........................................................................................................3-8
3.2.1.16 Measurement supervision...........................................................................................3-8
3.2.1.17 Set point alarms..........................................................................................................3-8
3.2.1.18 Status annunciations ..................................................................................................3-9
3.2.2 Measured values.......................................................................................... 3-10
3.2.2.1 Recorded measured values......................................................................................3-10
3.2.2.2 Measured values – mean values...............................................................................3-10
3.2.3 Metered measurands................................................................................... 3-10
4 Standard mapping 2-3 ................................................................................................... 4-1
4.1 Message in output direction ........................................................................... 4-1
4.1.1 Double commands (with checkback indication)............................................. 4-1
4.1.2 Single commands (without checkback indication) ......................................... 4-1
4.1.3 Internal commands ........................................................................................ 4-2
4.1.4 Application logic CFC..................................................................................... 4-2
4.2 Message in input direction ............................................................................. 4-4
4.2.1 Annunciations................................................................................................. 4-4
4.2.1.1 Double commands – checkback signals.....................................................................4-4
4.2.1.2 Single commands – status..........................................................................................4-4
4.2.1.3 Input channels with allocation to the binary inputs and tagging..................................4-5
4.2.1.4 Application logic CFC..................................................................................................4-5
4.2.1.5 Diagnosis ....................................................................................................................4-6
4.2.1.6 Measurement supervision...........................................................................................4-6
4.2.1.7 Set point alarms..........................................................................................................4-6
4.2.1.8 Status annunciations...................................................................................................4-7
4.2.2 Measured values............................................................................................ 4-8
4.2.2.1 Recorded measured values........................................................................................4-8
4.2.2.2 Measured values – mean values.................................................................................4-8
4.2.3 Metered measurands..................................................................................... 4-9
5 Standard mapping 2-4 ................................................................................................. 5-11
5.1 Message in output direction ......................................................................... 5-11
5.1.1 Double commands (with checkback indication)........................................... 5-11
5.1.2 Single commands (without checkback indication) ....................................... 5-11
5.1.3 Internal commands ...................................................................................... 5-11
5.1.4 Application logic CFC................................................................................... 5-12
5.2 Message in input direction ........................................................................... 5-13
5.2.1 Annunciations............................................................................................... 5-13
5.2.1.1 Double commands – checkback signals...................................................................5-13
5.2.1.2 Single commands – status........................................................................................5-13
5.2.1.3 Application logic CFC................................................................................................5-13
5.2.1.4 Time overcurrent protection......................................................................................5-13

Table of contents
7SJ61...7SJ63, 7SJ65, 6MD63 PROFIBUS-DP – Bus mapping
C53000-L1840-B006-02
viii
5.2.1.5 Sensitive ground fault protection...............................................................................5-14
5.2.1.6 Thermal overload protection......................................................................................5-14
5.2.1.7 Directional time overcurrent protection......................................................................5-14
5.2.1.8 Diagnosis...................................................................................................................5-14
5.2.2 Measured values.......................................................................................... 5-15
5.2.3 Metered measurands................................................................................... 5-15
6 Glossary.......................................................................................................................... 6-1
7 Index................................................................................................................................ 7-1

7SJ61...7SJ63, 7SJ65, 6MD63 PROFIBUS-DP – Bus mapping
C53000-L1840-B006-02 1-1
1 Data in the PROFIBUS-DP messages
Data in the PROFIBUS-DP
messages 1
1.1 Explanation
Note
The examples shown in this chapter 1.1 do not necessarily correspond
to the real allocation of the objects in the bus mapping.
The chapters 2 to 5 define the data area of the PROFIBUS-DP
messages for data transfer between the PROFIBUS-DP slave of the
SIPROTEC device 7SJ61...7SJ63, 7SJ65, 6MD63 with the PROFIBUS-
DP master.
The listed SIPROTEC objects in the PROFIBUS-DP message data area
are sorted after byte offset, beginning with 0.
Variables with data
type greater than
or equal to 1 byte
The offset defines the start of the most significant byte in the message,
e.g.:
Offset Designation of the
SIPROTEC objects Comments Scaling (32767 corresponds to ...) Internal object no.
2 Ia Current in phase A 3276.7 A 601
The measured value “Ia“ is assigned to data byte 2 (most significant byte
of the measured value) and data byte 3 (least significant byte of the
measured value) in the PROFIBUS-DP message.

Data in the PROFIBUS-DP messages
7SJ61...7SJ63, 7SJ65, 6MD63 PROFIBUS-DP – Bus mapping
C53000-L1840-B006-02
1-2
Bit variables
(SP/SC, DP/DC) The offset indicates the byte, which contains the bit value and the
position of bit 0 of the bit variable, e.g. (input message):
Offset Designation of the
SIPROTEC objects Comments Internal object no.
0/0 Q0 ON/OFF
OFF
0/1 Q0 ON/OFF
ON
Circuit breaker –
17/4 Fail Ph. Seq. 1 = Failure: Phase Sequence 171
The checkback signal from the circuit breaker (as double-point indi-
cation) is located in data byte 0, bit positions 20(bit 0) and 21(bit 1).
The single-point indication "Fail Ph. Seq.“ is located in byte 17, bit
position 24.
The definitions of data types (single-point indication, double-point
indication, measured value, metered measurand etc.) are contained
in the manual "7SJ61...63, 7SJ65, 6MD63, 7UM61 PROFIBUS-DP -
Communication profile" (ref. to page i).

Data in the PROFIBUS-DP messages
7SJ61...7SJ63, 7SJ65, 6MD63 PROFIBUS-DP – Bus mapping
C53000-L1840-B006-02 1-3
1.2 Messages in output direction: PROFIBUS-DP master to the
SIPROTEC device
The messages in PROFIBUS-DP output direction (ref. to chap. 2.1, 3.1,
4.1 and 5.1) allow:
•command outputs through the output relays of the SIPROTEC
device (external commands),
•manipulation of taggings (internal commands), which can be
changed by PROFIBUS-DP.
Note
The allocation of the output relays to the switching devices and to the
output channels is defined during parametrization of the SIPROTEC
devices.
Depending on the device composition there may be less than indicated
output relays (and corresponding PROFIBUS-DP message positions)
available in the SIPROTEC device.
1.3 Messages in input direction: SIPROTEC device to the PROFIBUS-
DP master
The messages in PROFIBUS-DP input direction (ref. to chap. 2.2, 3.2,
4.2 and 5.2) allow:
•polling of switching devices‘ status and binary inputs,
•transmission of annunciations, measurands and meter values to the
PROFIBUS-DP master.
1.3.1 Annunciations
Note
The allocation of the input channels to the binary inputs is defined during
parameterization of the devices.
Depending on the device composition and the existing protection
packages not all of the indicated binary inputs or protection
annunciations (and corresponding PROFIBUS-DP message positions)
may be available in the SIPROTEC device.

Data in the PROFIBUS-DP messages
7SJ61...7SJ63, 7SJ65, 6MD63 PROFIBUS-DP – Bus mapping
C53000-L1840-B006-02
1-4
1.3.2 Measured values
Note
Depending on the device composition not all of the indicated analog
inputs (and corresponding PROFIBUS-DP message positions) may be
available in the SIPROTEC device.
The given scaling values for the measured values in the standard
mappings apply to installations with the following nominal operating
values:
Nominal operating voltage of primary equipment (parameter address 1101):
è1.0 ... 10 (32) kV
Nominal operating current of primary equipment (parameter address 1102):
è10 ... 1000 A
Product of:
•Voltage transducer – Primary voltage (parameter address 0202) and
•Ratio factor Vph/Vdelta (parameter address 0206)
è>1.0 ... 10 (32) kV
Product of:
•Current transducer – Rated primary current (parameter address 0204) and
•Ratio factor IN/Iph (parameter address 0207) or (dependent on the device type)
•Ratio factor INs/Iph (parameter address 0208)
è0.0 ... 1000 A
Power values:
•Product of Nominal operating voltag and Nominal operating current of primary
equipment multiplied by 3
è>1.0 ... 10 (32) MW (MVAR)
Note
Changes of the scaling of the measured values are possible in
adaptation to the concrete installation enviroment. You find information
about this in the manual "7SJ61...63, 7SJ65, 6MD63, 7UM61
PROFIBUS-DP - Communication profile " (ref. to page i).

Data in the PROFIBUS-DP messages
7SJ61...7SJ63, 7SJ65, 6MD63 PROFIBUS-DP – Bus mapping
C53000-L1840-B006-02 1-5
1.3.3 Metered measurands
Scaling The scaling of the metered measurands, which are derived from
measured values, refers to:
60000 impulses per hour for V = Vnom and I = Inom
Vnom = NOMINAL OPERATING VOLTAGE OF PRIMARY EQUIPMENT
(parameter address = 1101)
Inom = NOMINAL OPERATING CURRENT OF PRIMARY EQUIPMENT
(parameter address = 1102)
Example In the parameter set is configured:
Inom = 100 A und Vnom = 12.00 kV,
60000 impulses correspond so that:
1 h * 100 A * 12 kV * 3= 2078.46 kWh
Note
•The type of the update (cyclic, with or without deletion) and the
update interval must be programmed for the metered measurands
(except for the operating hours meter) with the parameterization
software DIGSI.
•The scaling of the metered measurands at binary inputs ("Wp(puls)"
and "Wq(puls)") depends on the externally connected pulse
generator.

Data in the PROFIBUS-DP messages
7SJ61...7SJ63, 7SJ65, 6MD63 PROFIBUS-DP – Bus mapping
C53000-L1840-B006-02
1-6
1.4 Configuration data of the standard mappings 2-1 to 2-4
There are three standard mappings (standard mapping 2-1 to standard
mapping 2-4) available for the SIPROTEC devices 7SJ61...7SJ63,
7SJ65, 6MD63 for parameterization with DIGSI version 4.2 or higher
which differ in the data size of the PROFIBUS-DP messages.
Standard
mapping 2-1 The standard mapping 2-1 contains:
Output direction:
•7 double-point commands
•29 single-point commands
Input direction:
•7 double-point indications
•146 single-point indications,
•25 measured values (integer)
•6 metered measureands (unsigned long)
•Fault locator: Fault location (integer)
•Counter of operating hours (unsigned long)
Standard
mapping 2-2 The standard mapping 2-2 contains:
Output direction:
•7 double-point commands
•29 single-point commands
Input direction:
•7 double-point indications
•114 single-point indications
•10 measured values (integer)
•2 metered measurands (unsigned long)
•Counter of operating hours (unsigned long)
Standard
mapping 2-3 The standard mapping 2-3 contains:
Output direction:
•8 double-point commands
•24 single-point commands
Input direction:
•8 double-point indications
•64 single-point indications
•21 measured values (integer)
•6 metered measurands (unsigned long)
•Counter of operating hours (unsigned long)

Data in the PROFIBUS-DP messages
7SJ61...7SJ63, 7SJ65, 6MD63 PROFIBUS-DP – Bus mapping
C53000-L1840-B006-02 1-7
Standard
mapping 2-4 The standard mapping 2-4 contains:
Output direction:
•3 double-point commands
•5 single-point commands
Input direction:
•3 double-point indications
•26 single-point indications
•8 measured values (integer)
•2 metered measurands (unsigned long)
PROFIBUS-DP
configuration data Standard mapping 2-1: 1FH 1FH 1FH 1FH 1FH 1FH 13H 28H
(100 bytes input- and 9 bytes output direction)
Standard mapping 2-2: 1FH 1FH 1FH 28H
(48 bytes input- and 9 bytes output direction)
Standard mapping 2-3: 1FH 1FH 1FH 1FH 1FH 27H
(80 bytes input- and 8 bytes output direction)
Standard mapping 2-4: 1FH 1BH 21H
(28 bytes input- and 2 bytes output direction)
PROFIBUS-DP
master At the configuration of a PROFIBUS-DP slave of the SIPROTEC devices
in the parameterization system of the PROFIBUS-DP masters are to
select the following modules for the 7SJ61...7SJ63, 7SJ65, 6MD63
standard mappings and to allocate associated addresses in the I/O
addressing range of the PROFIBUS-DP master:
Standard mapping 2-1:
Module Order number Input
address Output address
0 Input – 16 Bytes Addr_Ix
1 Input – 16 Bytes Addr_Ix+16
2 Input – 16 Bytes Addr_Ix+32
3 Input – 16 Bytes Addr_Ix+48
4 Input – 16 Bytes Addr_Ix+64
5 Input – 16 Bytes Addr_Ix+80
6 Input – 4 Bytes Addr_Ix+96
7 Output – 9 Bytes Addr_Ox
Standard mapping 2-2:
Module Order number Input
address Output address
0 Input – 16 Bytes Addr_Ix
1 Input – 16 Bytes Addr_Ix+16
2 Input – 16 Bytes Addr_Ix+32
3 Output – 9 Bytes Addr_Ox

Data in the PROFIBUS-DP messages
7SJ61...7SJ63, 7SJ65, 6MD63 PROFIBUS-DP – Bus mapping
C53000-L1840-B006-02
1-8
Standard mapping 2-3:
Module Order number Input
address Output address
0 Input – 16 Bytes Addr_Ix
1 Input – 16 Bytes Addr_Ix+16
2 Input – 16 Bytes Addr_Ix+32
3 Input – 16 Bytes Addr_Ix+48
4 Input – 16 Bytes Addr_Ix+64
5 Output – 8 Bytes Addr_Ox
Standard mapping 2-4:
Module Order number Input
address Output address
0 Input – 16 Bytes Addr_Ix
1 Input – 12 Bytes Addr_Ix+16
5 Output – 2 Bytes Addr_Ox
Addr_Ix and Addr_Ox indicate arbitrary (as a rule even) addresses in the
I/O addressing range of the PROFIBUS-DP master.
Addr_Ix (base address of the inputs) is identical with offset 0 of the
PROFIBUS-DP message data of the SIPROTEC device in input
direction (ref. to chap. 2.2, 3.2, 4.2 and 5.2).
Addr_Ox (base address of the outputs) is identical with offset 0 of the
PROFIBUS-DP message data of the SIPROTEC device in output
direction (ref. to chap. 2.1, 3.1, 4.1 and 5.1).
Note
There is dependently on the PROFIBUS-DP master in addition possibly
the demand to put the base address of the inputs on a value divisible by
four so that accesses on the metered measurands (unsigned long
values, ref. to chap. 2.2.4, 3.2.3, 4.2.3 and 5.2.3) can be correctly
carried out in the PROFIBUS-DP master.
Compatibility to
DIGSI 4.1 standard
mappings
The standard mappings 1 to m (m = device type dependent number of
standard mappings) enclosed to DIGSI 4.1 can be replaced by the
standard mappings 2-1 to 2-3 to make customizations of the allocation
and scaling possible.
The following relations are valid:
corresponds to DIGSI 4.1 mapping
DIGSI 4.2 mapping in the size in the measured
value scaling
Standard mapping 2-1 Standard mapping 1 to 4 of
the devices 7SJ62/63 Standard mapping 1 of the device 7SJ62/63
Standard mapping 2-2 Standard mapping 1 and 2 of
the device 7SJ61 Standard mapping 1 of the device 7SJ61
Standard mapping 2-3 Standard mapping 1 to 3 of
the device 6MD63 Standard mapping 1 of the device 6MD63

Data in the PROFIBUS-DP messages
7SJ61...7SJ63, 7SJ65, 6MD63 PROFIBUS-DP – Bus mapping
C53000-L1840-B006-02 1-9
The DIGSI 4.1 standard mappings are not component of this
documentation. You find associated information in the following
manuals:
Manual Contents Order number
PROFIBUS-DP
Bus mapping
7SJ61
Data in the PROFIBUS-DP messages
of the SIPROTEC device 7SJ61 C53000-L1840-B002-01
PROFIBUS-DP
Busmapping
7SJ62/63
Data in the PROFIBUS-DP messages
of the SIPROTEC devices 7SJ62/63 C53000-L1840-B003-01
PROFIBUS-DP
Bus mapping
6MD63
Data in the PROFIBUS-DP messages
of the SIPROTEC device 6MD63 C53000-L1840-B004-01

Data in the PROFIBUS-DP messages
7SJ61...7SJ63, 7SJ65, 6MD63 PROFIBUS-DP – Bus mapping
C53000-L1840-B006-02
1-10
1.5 Notes to SIPROTEC objects
This chapter contains notes for the use and evaluation of certain
SIPROTEC objects.
The description of the standard mappings (ref. to chap. 2 to 5)
contains the pre-allocation of the mapping files at delivery or first
assignment of a mapping in DIGSI to the SIPROTEC device.
Changes of the allocation and the scaling of the measured values
are possible in adaptation to the concrete installation enviroment.
You find information about this in the manual "7SJ61...63, 7SJ65,
6MD63, 7UM61 PROFIBUS-DP - Communication profile" (ref. to
page i).
If a mapping file is assigned to a SIPROTEC device and if the data
size of the PROFIBUS-DP message of this SIPROTEC device is
changed by choice of a new mapping file then assignments which
are not available in the existing mapping file remain unassigned
furthermore.
1.5.1 Single commands
The command output mode (pulse output, continuous output) is
changeable for the single commands using parameterization software
DIGSI. The command output modes indicated in the standard mappings
are predefined.
The switching direction OFF for single commands with pulse output is
not permitted and is rejected in the SIPROTEC device.
References Standard mapping 2-1: ref. to chap. 2.1.2
Standard mapping 2-2: ref. to chap. 3.1.2
Standard mapping 2-3: ref. to chap. 4.1.2
Standard mapping 2-4: ref. to chap. 5.1.2