Siemens SIMATIC ET 200S User manual

Digital Electronic Module
2RO NO/NC DC24..48V/5A AC24..230V/5A
(6ES7132-4HB13-0AB0)
SIMATIC
Distributed I/O ET 200S
Digital Electronic Module
2RO NO/NC DC24..48V/5A AC24..230V/5A
(6ES7132-4HB13-0AB0)
Manual
08/2019
A5E48281338
-AA
Preface
1
Properties
2
Parameters
3
Diagnostics
4

Siemens AG
Large Drives Applications
Vogelweiherstr. 1
-15
90441 NÜRNBERG
GERMANY
A5E48281338-AA
Ⓟ
08/2019 Subject to change
Copyright © Siemens AG 2019.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

Digital Electronic Module 2RO NO/NC DC24..48V/5A AC24..230V/5A (6ES7132-4HB13-0AB0)
Manual, 08/2019, A5E48281338-AA 3
Table of contents
1 Preface ...................................................................................................................................................... 4
1.1 Preface......................................................................................................................................4
2 Properties .................................................................................................................................................. 6
2.1 Digital Electronic Module 2RO NO/NC DC24..48V/5A AC24..230V/5A (6ES7132-
4HB13-0AB0)............................................................................................................................6
3 Parameters.............................................................................................................................................. 11
4 Diagnostics.............................................................................................................................................. 12
4.1 Diagnostics using LED display ...............................................................................................12

Digital Electronic Module 2RO NO/NC DC24..48V/5A AC24..230V/5A (6ES7132-4HB13-0AB0)
4Manual, 08/2019, A5E48281338-AA
Preface
1
1.1 Preface
Purpose of the manual
This manual supplements the ET 200S Distributed I/O System Operating Instructions.
Functions which apply to the ET 200S in general are described in the ET 200S operating
instructions on the Internet (https://support.automation.siemens.com/WW/view/en/1144348).
The information in this document along with the operating instructions enables you to
commission the ET 200S.
Basic knowledge requirements
To understand these operating instructions you should have general knowledge of
automation engineering.
Scope of validity of the manual
This manual applies to this ET 200S module. It describes the components that are valid at
the time of publication.
Recycling and disposal
Due to the fact that it is low in contaminants, this ET 200S module is recyclable. For
environmentally compliant recycling and disposal of your electronic waste, please contact a
company certified for the disposal of electronic waste.
Additional support
If you have any questions relating to the use of the products described in this manual and do
not find the answers in this document, please contact your local Siemens representative or
office nearest to you on the Internet (https://www.automation.siemens.com/partner/).
A guide to the technical documentation for the various SIMATIC products and systems is
available on the Internet. (https://www.siemens.com/simatic-tech-doku-portal)
The online catalog and ordering system are available on the Internet
(https://www.siemens.com/automation/mall).
Training center
We offer courses to help you get started with the ET 200S and the SIMATIC S7 automation
system. Please contact your regional training center or the central training center in D-
90327, Nuremberg, Germany on the Internet (https://www.siemens.com/sitrain).

Preface
1.1 Preface
Digital Electronic Module 2RO NO/NC DC24..48V/5A AC24..230V/5A (6ES7132-4HB13-0AB0)
Manual, 08/2019, A5E48281338-AA 5
Technical Support
You can reach Technical Support for all industry automation products via the support request
Web form on the Internet (https://www.siemens.com/automation/support-request).
Additional information about Siemens Technical Support is available on the Internet
(https://www.siemens.com/automation/service).
Service & Support on the Internet
In addition to our documentation, we offer a comprehensive knowledge base on the Internet
(https://www.siemens.com/automation/service&support).
There you will find:
●Our Newsletter, which constantly provides you with the latest information about your
products.
●The right documentation for you using our Service & Support search engine.
●The bulletin board, a worldwide knowledge exchange for users and experts.
●Your local contact for Automation & Drives in our contact database.
●Information about on-site services, repairs, spare parts, and lots more.

Digital Electronic Module 2RO NO/NC DC24..48V/5A AC24..230V/5A (6ES7132-4HB13-0AB0)
6Manual, 08/2019, A5E48281338-AA
Properties
2
2.1 Digital Electronic Module
2RO NO/NC DC24..48V/5A AC24..230V/5A
(6ES7132-4HB13-0AB0)
Properties
●Digital electronic module with two relay outputs
●Output current 5 A per output
●Substitute value
●Suitable for solenoid valves, DC contactors, and indicator lights
●Isolated from the supply voltage
●Normally opened and normally closed contacts
Note
If you connect an extra
-low voltage system (SELV/PELF) on one channel of the relay
subassembly, you can only use an extra
-low voltage system (SELV/PELF) on the other
channel.
General terminal assignment
Note
Terminals 4, 8, A4, A8, A3 and A7 are only available at specified terminal modules.
Pin assignment for 2RO NO/NC DC24..48V/5A AC24..230V/5A (6ES7132-4HB13-0AB0)
Terminal
Assignment
Terminal
Assignment
Notes
1
Common
0
5
Common
1
•Commonn, NOCnor NCCn, channel n
•n.c.: Not connected (max. 30 VDC can be connected)
•AUX1: Protective-conductor terminal or potential bus (freely
usable up to 230 VAC)
2
Normally open
contact0
6
Normally
open contact1
3
Normally
closed contact0
7
Normally
closed con-
tact
1
4
n.c.
8
n.c.
A4
AUX1
A8
AUX1
A3
AUX1
A7
AUX1

Properties
2.1 Digital Electronic Module 2RO NO/NC DC24..48V/5A AC24..230V/5A (6ES7132-4HB13-0AB0)
Digital Electronic Module 2RO NO/NC DC24..48V/5A AC24..230V/5A (6ES7132-4HB13-0AB0)
Manual, 08/2019, A5E48281338-AA 7
Usable terminal modules
Usable terminal modules for 2RO NO/NC DC24..48V/5A AC24..230V/5A (6ES7132-4HB13-0AB0)
TM-E15C26-A1
(6ES7193-4CA50-
0AA0)
TM-E15C24-A1
(6ES7193-4CA30-
0AA0)
TM-E15C24-01
(6ES7193-4CB30-
0AA0)
TM-E15C23-01
(6ES7193-4CB10-
0AA0)
Spring terminal
TM-E15S26-A1
(6ES7193-4CA40-
0AA0)
TM-E15S24-A1
(6ES7193-4CA20-
0AA0)
TM-E15S24-01
(6ES7193-4CB20-
0AA0)
TM-E15S23-01
(6ES7193-4CB00-
0AA0)
Screw-type terminal
TM-E15N26-A1
(6ES7193-4CA80-
0AA0)
TM-E15N24-A1
(6ES7193-4CA70-
0AA0)
TM-E15N24-01
(6ES7193-4CB70-
0AA0)
TM-E15N23-01
(6ES7193-4CB60-
0AA0)
Fast Connect
Block diagram
Figure 2-1 Block diagram of the 2RO NO/NC DC24..48V/5A AC24..230V/5A

Properties
2.1 Digital Electronic Module 2RO NO/NC DC24..48V/5A AC24..230V/5A (6ES7132-4HB13-0AB0)
Digital Electronic Module 2RO NO/NC DC24..48V/5A AC24..230V/5A (6ES7132-4HB13-0AB0)
8Manual, 08/2019, A5E48281338-AA
Technical specifications 2RO NO/NC DC24..48V/5A AC24..230V/5A (6ES7132-4HB13-0AB0)
Dimensions and weight
Width (mm)
15
Weight
Approx. 50 g
Module-specific data
Supports isochronous operation No
Number of outputs
2
Cable length
•Unshielded Max. 600 m
•Shielded Max. 1000 m
Parameter length
3 bytes
Address space
1 byte
Address space (packed)
2 bits
Voltages, currents, potentials
Rated supply voltage L+ (from the power module)
24 V DC
Reverse polarity protection Current per channel
Yes
•Up to 50°C Max. 5 A
•Up to 60°C Max. 4 A
Electrical isolation
•Between the channels Yes
•Between channels and backplane bus Yes
•Between channels and supply voltage Yes
•Between the supply voltage and backplane
bus
Yes
Permissible potential difference
•Between channels and backplane bus 240 VAC
•Between channels and supply voltage 240 VAC
Insulation tested
•Between the supply voltage and backplane
bus
500 VDC
•Between channels and backplane bus 2500 VDC
•Between channels and supply voltage 2500 VDC
Current consumption
•From the power supply L+ max. 30 mA
•From backplane bus max. 10 mA
Power dissipation of the module
Typically 0.6 W

Properties
2.1 Digital Electronic Module 2RO NO/NC DC24..48V/5A AC24..230V/5A (6ES7132-4HB13-0AB0)
Digital Electronic Module 2RO NO/NC DC24..48V/5A AC24..230V/5A (6ES7132-4HB13-0AB0)
Manual, 08/2019, A5E48281338-AA 9
Dimensions and weight
Status, interrupts, diagnostics
Status display
Green LED per channel
Diagnostics functions
No
Status, interrupts, diagnostics
Status display
Green LED per channel
Diagnostics functions
No
Data for selecting an actuator
Output current
•Continuous thermal current Max. 5 A
•Minimum load current 8 mA
Connecting two outputs in parallel
•For redundant control of a load No
•To increase performance No
Control of a digital input
Yes
Switch rate
•For resistive load 2 Hz
•On inductive load 0.5 Hz
•For lamp load 2 Hz
Limitation (internal) of the voltage induced on
circuit interruption
No
Short-circuit protection of the output
1
No
1The relay outputs must be fused externally with 6 A. For installation in a hazardous area as speci-
fied by the National Electric Code (NEC) the fuse must only be removed with a suitable tool if the
subassembly is not in an explosive area.

Properties
2.1 Digital Electronic Module 2RO NO/NC DC24..48V/5A AC24..230V/5A (6ES7132-4HB13-0AB0)
Digital Electronic Module 2RO NO/NC DC24..48V/5A AC24..230V/5A (6ES7132-4HB13-0AB0)
10 Manual, 08/2019, A5E48281338-AA
Switching capacity and lifetime of the contacts
With an external protective circuit, the contacts will last longer than specified in the following
table.
The normally open and normally closed contacts of the relay have a different lifetime. The
table shows the switching capacity and lifetime of the contacts.
Table 2- 1 Switching capacity and lifetime of the contacts
Resistive load
Voltage
Current
Duty cycles (typ.)
Normally open con-
tact
Duty cycles (typ.)
Normally closed
contact
For resistive load
24 V DC
5.0 A
0.1 million
0.15 million
4.0 A
0.2 million
0.175 million
2.0 A
0.45 million
0.3 million
0.5 A
1.4 million
1.1 million
0.1 A
1.5 million
1.5 million
48 VDC
2.0 A
0.15 million
0.11 million
1.0 A
0.3 million
0.2 million
0.5 A
0.6 million
0.6 million
0.1 A
0.8 million
0.6 million
48 VAC
2.0 A
0.45 million
0.35 million
60 VAC
2.0 A
0.45 million
0.35 million
120 VAC
5.0 A
0.1 million
0.1 million
3.0 A
0.2 million
0.2 million
2.0 A
0.4 million
0.3 million
1.0 A
0.8 million
0.6 million
0.5 A
1.5 million
1.0 million
230 VAC
5.0 A
0.1 million
0.1 million
3.0 A
0.2 million
0.2 million
2.0 A
0.4 million
0.3 million
1.0 A
0.8 million
0.6 million
0.5 A
1.5 million
1.0 million
For inductive load in
accordance with IEC
947-5-1 DC 13/ AC
15
24 V DC
2.0 A
0.1 million
0.1 million
1.0 A
0.2 million
0.2 million
0.5 A
0.5 million
0.5 million
48 VDC
2.0 A
0.07 million
0.05 million
1.0 A
0.15 million
0.1 million
0.5 A
0.4 million
0.25 million
48 VAC
1.0 A
0.5 million
0.3 million
60 VAC
1.0 A
0.5 million
0.3 million
120 VAC
2.0 A
0.1 million
0.1 million
1.0 A
0.3 million
0.1 million
0.5 A
0.9 million
0.6 million
0.1 A
1.5 million
1.0 million
230 VAC
2.0 A
0.1 million
0.1 million
1.0 A
0.5 million
0.3 million
0.5 A
0.9 million
0.6 million
0.1 A
1.0 million
1.0 million