Siemens SIMOTION D425 User manual

SIMOTION SIMOTIONCOUT D4x5
_
_____________
_
_____________
_
_____________
_
_____________
_
_____________
_
_____________
_
_____________
_
_____________
Preface
Description
1
Operator control (hardware)
2
Interfaces
3
Technical Data
4
Dimension drawings
5
Spare parts/accessories
6
Standards and approvals
A
ESD guidelines
B
SIMOTION
SIMOTION
D4x5
Manual
05/2009
Valid for SIMOTION D425, D435, D445, and D445-1

Legal information
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.
CAUTION
without a safety alert symbol, indicates that property damage can result if proper precautions are not taken.
NOTICE
indicates that an unintended result or situation can occur if the corresponding information is not taken into
account.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The device/system may only be set up and used in conjunction with this documentation. Commissioning and
operation of a device/system may only be performed by qualified personnel. Within the context of the safety notes
in this documentation qualified persons are defined as persons who are authorized to commission, ground and
label devices, systems and circuits in accordance with established safety practices and standards.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be adhered to. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of the Siemens AG. The remaining trademarks in this
publication may be trademarks whose use by third parties for their own purposes could violate the rights of the
owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Siemens AG
Industry Sector
Postfach 48 48
90026 NÜRNBERG
GERMANY
Copyright © Siemens AG 2009.
Technical data subject to change

D4x5
Manual, 05/2009 3
Preface
Content of the Manual
This document is part of the SIMOTION D4xx documentation package.
Scope
The SIMOTION D4x5 manual is applicable to the SIMOTION D425, SIMOTION D435,
SIMOTION D445/D445-1, and SIMOTION CX32 devices.
Standards
The SIMOTION system was developed in accordance with ISO 9001 quality guidelines.
Content of the manual
The following is a description of the purpose and use of the product manual:
● Description
Provides information about the SIMOTION system and its integration in the automation
environment.
● Operator control (hardware)
Provides information about the structure and architecture of the devices.
● Interfaces
Provides information about the different interfaces of the devices, their pin assignment,
and possible applications.
● Technical data
Provides information about the properties and features of the devices.
● Dimension drawings
● Spare parts/accessories
Provides information about spare parts and accessories of the SIMOTION D4x5 and
SIMOTION CX32.
● Appendix
Provides information about the various standards and specifications fulfilled by the
device.
● Index for locating information.

Preface
D4x5
4 Manual, 05/2009
SIMOTION Documentation
An overview of the SIMOTION documentation can be found in a separate list of references.
This documentation is included as electronic documentation with the supplied SIMOTION
SCOUT.
The SIMOTION documentation consists of 9 documentation packages containing
approximately 80 SIMOTION documents and documents on related systems (e.g.
SINAMICS).
The following documentation packages are available for SIMOTION V4.1 SP4:
● SIMOTION Engineering System
● SIMOTION System and Function Descriptions
● SIMOTION Service and Diagnostics
● SIMOTION Programming
● SIMOTION Programming - References
● SIMOTION C
● SIMOTION P350
● SIMOTION D4xx
● SIMOTION Supplementary Documentation
Hotline and Internet addresses
Siemens Internet address
The latest information about SIMOTION products, product support, and FAQs can be found
on the Internet at:
● General information:
– http://www.siemens.de/simotion (German)
– http://www.siemens.com/simotion (international)
● Downloading documentation
Further links for downloading files from Service & Support.
http://support.automation.siemens.com/WW/view/en/10805436
● Individually compiling documentation on the basis of Siemens contents with the My
Documentation Manager (MDM), refer to http://www.siemens.com/mdm
My Documentation Manager provides you with a range of features for creating your own
documentation.
● FAQs
You can find information on FAQs (frequently asked questions) by clicking
http://support.automation.siemens.com/WW/view/en/10805436/133000.
Additional support
We also offer introductory courses to help you familiarize yourself with SIMOTION.

Preface
D4x5
Manual, 05/2009 5
For more information, please contact your regional Training Center or the main Training
Center in 90027 Nuremberg, Germany.
Information about training courses on offer can be found at:
www.sitrain.com
Technical support
If you have any technical questions, please contact our hotline:
Europe / Africa
Phone [phone] (subject to charge)
Fax [phone]
€0.14/min from German wire-line network, mobile phone prices may differ.
Internet http://www.siemens.com/automation/support-request
Americas
Phone [phone]
Fax [phone]
E-mail mailto:[email protected]
Asia / Pacific
Phone [phone]
Fax [phone]
E-mail mailto:support.asia.automatio[email protected]
Note
Country-specific telephone numbers for technical support are provided under the following
Internet address:
http://www.automation.siemens.com/partner
Questions about this documentation
If you have any questions (suggestions, corrections) regarding this documentation, please
fax or e-mail us at:
Fax [phone]
E-mail mailto:[email protected]

Preface
D4x5
6 Manual, 05/2009
Product disposal
SIMOTION D is an environmentally friendly product. It includes the following features:
● In spite of its excellent resistance to fire, the flame-resistant agent in the plastic used for
the housing does not contain halogens.
● Identification of plastic materials in accordance with DIN 54840
● Less material used because the unit is smaller and with fewer components thanks to
integration in ASICs.
For state-of-the art environmentally friendly recycling and disposal of your old modules,
contact your local Siemens representative. Contact details can be found in our contacts
database on the Internet at:
http://www.automation.siemens.com/partner/index.asp
Further information / FAQs
You can find further information on this manual under the following FAQs:
http://support.automation.siemens.com/WW/view/de/27585482
You can also find additional information:
● SIMOTION Utilities & Applications: SIMOTION Utilities & Applications will be included in
the SIMOTION SCOUT scope of delivery and, along with FAQs, also contain free utilities,
e.g. calculation tools, optimization tools etc. as well as application examples (ready-to-
apply solutions such as winders, cross cutters or handling).
● The latest SIMOTION FAQs are online at
http://support.automation.siemens.com/WWview/de/10805436
● SIMOTION SCOUT online help
● For additional documentation (separate document), please refer to the list of references.

D4x5
Manual, 05/2009 7
Table of contents
Preface ...................................................................................................................................................... 3
1 Description................................................................................................................................................. 9
1.1 System overview............................................................................................................................9
1.2 System components ....................................................................................................................13
1.3 I/O integration...............................................................................................................................17
1.4 Representation of SIMOTION D425 and SIMOTION D435 ........................................................18
1.5 Representation of SIMOTION D445 ............................................................................................19
1.6 SIMOTION D445-1 image............................................................................................................21
1.7 Nameplates..................................................................................................................................22
1.8 Safety notes .................................................................................................................................24
1.9 CompactFlash card......................................................................................................................25
1.9.1 Usage and function of the CompactFlash Card...........................................................................25
1.9.2 CompactFlash card......................................................................................................................27
2 Operator control (hardware)..................................................................................................................... 29
2.1 Overview of operator control and display elements.....................................................................29
2.2 Operator control elements ...........................................................................................................31
2.2.1 Service and operating mode switch.............................................................................................31
2.2.2 RESET button ..............................................................................................................................33
2.3 LED displays ................................................................................................................................34
3 Interfaces................................................................................................................................................. 37
3.1 Interface overview........................................................................................................................37
3.2 DRIVE-CLiQ interfaces ................................................................................................................38
3.3 Ethernet interfaces.......................................................................................................................39
3.4 Digital inputs/digital outputs .........................................................................................................42
3.4.1 Features.......................................................................................................................................42
3.4.2 Using the digital inputs/outputs....................................................................................................45
3.5 Power supply................................................................................................................................46
3.6 PROFIBUS DP interfaces ............................................................................................................47
3.7 Slot for CompactFlash Card.........................................................................................................50
3.8 Measuring sockets .......................................................................................................................50
3.9 USB interfaces .............................................................................................................................51
3.10 Option slot....................................................................................................................................51
4 Technical Data......................................................................................................................................... 53
4.1 Technical data D4x5 ....................................................................................................................53

Table of contents
D4x5
8 Manual, 05/2009
4.2 Clock ........................................................................................................................................... 58
4.3 D4x5 power supply...................................................................................................................... 59
4.4 Information on insulation tests, safety class, and degree of protection ...................................... 60
4.5 Input and output circuit................................................................................................................ 61
5 Dimension drawings ................................................................................................................................ 63
5.1 Dimension drawing of D425 and D435 ....................................................................................... 63
5.2 Dimension drawing of D445........................................................................................................ 64
5.3 D445-1 dimension drawing ......................................................................................................... 65
5.4 CAD data, dimension drawings, and circuit-diagram macros..................................................... 66
6 Spare parts/accessories .......................................................................................................................... 67
6.1 Supplemental system components .............................................................................................67
6.2 Fan/battery module ..................................................................................................................... 68
6.2.1 Cooling SIMOTION D4x5 and buffering data.............................................................................. 68
6.2.2 Installing the fan/battery module ................................................................................................. 70
6.2.3 Replace battery in the fan/battery module .................................................................................. 71
6.3 Terminal board TB30 .................................................................................................................. 72
6.4 CBE30 communication board ..................................................................................................... 73
6.5 Terminal module TM31 ............................................................................................................... 74
6.6 Terminal module TM41 ............................................................................................................... 75
6.7 Terminal Module TM54F............................................................................................................. 75
6.8 Terminal modules TM15 and TM17 High Feature ...................................................................... 76
6.9 CUA31/CUA32 control unit adapter............................................................................................ 77
6.10 DMC20 DRIVE-CLiQ hub............................................................................................................ 78
6.11 Controller Extension CX32.......................................................................................................... 79
6.12 Available spare parts and accessories ....................................................................................... 81
A Standards and approvals......................................................................................................................... 83
A.1 General rules............................................................................................................................... 83
A.2 Safety of electronic controllers.................................................................................................... 84
A.3 Electromagnetic compatibility ..................................................................................................... 86
B ESD guidelines ........................................................................................................................................ 87
B.1 ESD definition ............................................................................................................................. 87
B.2 Electrostatic charging of individuals............................................................................................ 87
B.3 Basic measures for protection against discharge of static electricity ......................................... 88
Index........................................................................................................................................................ 89

D4x5
Manual, 05/2009 9
Description 1
1.1 System overview
Overview
SIMOTION D is a drive-based version of SIMOTION based on the SINAMICS S120 drive
family.
With SIMOTION D, the SIMOTION PLC and motion control functionalities as well as the
SINAMICS S120 drive software run on shared control hardware.
SIMOTION D is available in two versions:
● SIMOTION D410 is a compact control unit for single-axis applications and is snapped on
to the SINAMICS S120 PM340 Power Module in blocksize format.
● SIMOTION D4x5 is a control unit for multi-axis applications in SINAMICS S120 booksize
format and is offered in several performance variants:
– SIMOTION D425 (BASIC performance) for up to 16 axes
– SIMOTION D435 (STANDARD performance) for up to 32 axes
– SIMOTION D445/D445-1 (HIGH Performance) for up to 64 axes
Compared with SIMOTION D445, SIMOTION D445-1 offers an improvement in PLC
and motion control performance of approximately 30%, depending on the application.
Consequently, SIMOTION D445-1 is the preferred solution for new applications as of
V4.1 SP2.
This manual describes the SIMOTION D4x5 for multi-axis applications. Separate manuals
are available for the SIMOTION D410 single-axis module.
Like SINAMICS S120, SIMOTION D also follows the Totally Integrated Automation (TIA)
concept. TIA is characterized by integrated data management, configuration, and
communication for all products and systems. Thus, an extensive toolbox of automation
modules is also available for SIMOTION D.
Note
In order to cover all versions of SIMOTION D for multi-axis applications, the product will be
referred to as "D4x5". Specific product designations will be used for information that applies
only to one product version, e.g., D435.
Application
SIMOTION D4x5 is ideally suited to applications with many coordinated axes with high clock-
pulse rates.
Typical applications include:
● Compact multiple-axis machines
● High-performance applications with short machine cycles

Description
1.1 System overview
D4x5
10 Manual, 05/2009
● Compact machines
– Including the complete machine control in the drive
– With extensive connection possibilities for communication, HMI and I/O
● Distributed drive concepts
– Applications with many axes
– Synchronization of several SIMOTION D Control Units using distributed synchronous
operation
Versions
The individual versions - SIMOTION D425 (BASIC Performance), SIMOTION D435
(STANDARD Performance), and SIMOTION D445/D445-1 (HIGH Performance) - differ in
terms of their PLC performance and motion control performance. The main distinguishing
features are:
SIMOTION D425 SIMOTION D435 SIMOTION D445/D445-1
Maximum number of axes 16 32 64
Minimum servo/interpolator
cycle clock
2.0 ms 1.0 ms 0.5 ms
DRIVE-CLiQ interfaces 4 4 6
SIMOTION D4x5 features PLC and motion control performance (open-loop control and
motion control) for up to 16, 32 or 64 axes, as required.
Due to the following functional improvements, for new applications we recommend using
SIMOTION D445-1 (V4.1 SP2 or higher) instead of SIMOTION D445:
● an increase of around 30% in PLC and motion control performance, depending on the
application
● Less mounting depth (mounting is possible even without spacers)
● Double-fan/battery module for higher availability
● Further information (http://support.automation.siemens.com/WW/view/en/31507782).
The computing functions integrated into the drive allow the D4x5 Control Unit to operate up
to six servo, four vector or eight V/f axes.
The drive control supports servo control (for maximum dynamic response), vector control (for
maximum torque accuracy) and V/f control.
Note
With the SIZER configuration tool, you can easily configure the SINAMICS S120 drive family
including SIMOTION.
It provides you with support for selecting and dimensioning the components required for a
Motion Control task.
You can also determine the possible number of axes and the resulting load with SIZER in
accordance with your performance requirements.

Description
1.1 System overview
D4x5
Manual, 05/2009 11
Hardware components: SIMOTION runtime system and SINAMICS drive control
As the central hardware, SIMOTION D uses the SIMOTION D4x5 as a Control Unit
consisting of the SIMOTION runtime system and the SINAMICS drive control. The Control
Unit uses the SINAMICS Integrated drive with various SINAMICS S120 drive modules (Line
and Motor Modules) to perform open-loop and closed-loop control of the axis grouping. A
range of additional SINAMICS S120 components, such as SMx encoder systems or terminal
modules can be connected via DRIVE-CLiQ. With a few exceptions (e.g. no basic positioner
EPos, no Basic Operator Panel BOP20, etc.) the drive control integrated in SIMOTION D
has the same control characteristics and performance features as the SINAMICS S120
CU320 Control Unit. The EPos functionality is provided by the SIMOTION technology
functions. The functionality of SIMOTION D can be expanded with the distributed I/O via
PROFIBUS or with the CBE30 Ethernet Communication Board via PROFINET IO.
The following figure shows a typical SIMOTION D axis grouping.
'5,9(&/L4,2GHYLFHV
7HUPLQDOPRGXOHV
'5,9(&/L4
'5,9(&/L4
3RZHU
ᆰᆱᆲᆲ
ᆳ
ᆳ
Figure 1-1 Example of a SIMOTION D4x5 axis assembly
A SIMOTION D axis grouping generally consists of the following elements:
● SIMOTION D (Control Unit) (1)
This unit contains the programmable runtime system of SIMOTION and the drive software
of SINAMICS S120. In principle, SIMOTION D is capable of controlling multiple
axes/drives.
● One SINAMICS infeed (Line Module) (2)
This module generates a DC link from the supply system.

Description
1.1 System overview
D4x5
12 Manual, 05/2009
● SINAMICS power units (Motor Modules) (3)
These modules are used to control motors.
It is also possible to operate SINAMICS PM340 Power Modules with the SINAMICS
Control Unit adapter (CUA). A separate infeed is then unnecessary.
● DRIVE-CLiQ components (4)
In SINAMICS S120/SIMOTION D, the individual components of the drive system
communicate with each other via DRIVE-CLiQ. In addition to power components,
encoder systems and special DRIVE-CLiQ I/O devices can also be linked via DRIVE-
CLiQ.
Extension of the drive computing performance
The motion control performance of a SIMOTION D4x5 can be utilized in full by expanding
the computing performance at the drive in two different ways:
● Over PROFIBUS or PROFINET, SINAMICS S120 CU320/CU310 Control Units complete
with further SINAMICS S120 drive modules can be connected.
● With SIMOTION D435 and D445/D445-1, the CX32 Controller Extension can be
connected over DRIVE-CLiQ. This module is extremely compact and can control up to
6 servo, 4 vector or 8 V/
f axes.
Software components: SIMOTION runtime system and SINAMICS drive control
The basic functionality of SIMOTION D is supplied on a Compact Flash card containing the
following:
SIMOTION runtime system including the following functions:
● User-programmable runtime system (IEC 61131)
● Various runtime levels (tasks)
● PLC and arithmetic functionality
● Motion control functions
● Communication functions
SINAMICS S120 drive control including the following functions:
● Closed-loop current and torque control
● Closed-loop speed control
● Closed-loop infeed

Description
1.2 System components
D4x5
Manual, 05/2009 13
1.2 System components
Central components
SIMOTION D4x5 communicates with automation components via the following interfaces:
● PROFIBUS DP
● Ethernet
● PROFINET (when using a CBE30)
● DRIVE-CLiQ (DRIVE Component Link with IQ)
SIMOTION D features a SINAMICS Integrated drive element. Communication with the
SINAMICS Integrated is via PROFIBUS mechanisms (DP Integrated).
The most important components of the system and their functions are shown below.
Table 1- 1 Central components
Component Function
SIMOTION D4x5 controller ... is the central motion control module.
This module contains the programmable SIMOTION runtime for the
SIMOTION D4x5 and the SINAMICS S120 drive software.
You can use the integrated high-speed digital I/Os as:
•Homing inputs
•Inputs for measuring inputs
•User-addressable process inputs/outputs
•Outputs for fast output cams
The measuring sockets can output any analog signals.
System software The basic functionality of SIMOTION D is supplied on a Compact Flash
card containing the following:
•SIMOTION runtime (kernel)
•Drive software of SINAMICS S120 - implements all drive functions
Power supply ... provides the electronic power supply for SIMOTION D, e.g. via the
SITOP power supply.
PROFIBUS DP
The control unit can communicate with the following components via the PROFIBUS DP
interfaces:
Table 1- 2 Components on PROFIBUS DP
Component Function
Programming device (PG/PC) ... configures, parameterizes, programs, and tests with the
"SIMOTION SCOUT" engineering system (ES)
SIMATIC HMI device ... is used for operating and monitoring functions. This is not an
essential requirement for the operation of a Control Unit.
Other controllers (e.g.
SIMOTION or SIMATIC)
.. e.g. higher-level controller (plant controller); modular machine
concepts with multiple controls, distributed across individual machine
modules

Description
1.2 System components
D4x5
14 Manual, 05/2009
Component Function
Distributed I/O systems
SIMATIC ET 200M Modular I/O system for control cabinet installation and high channel
density
SIMATIC ET 200S Finely scalable I/O system for control cabinet configuration and
particularly time-critical applications; including motor starters, safety
technology and individual grouping of load groups
SIMATIC ET 200pro Modular I/O system with IP65/67 degree of protection for machine-
related applications with no control cabinet; with features such as
compact designs, integrated PROFIsafe safety technology,
PROFINET connection and live module replacement.
SIMATIC ET 200eco I/O system with IP65/67 degree of protection for cabinet-free use
close to the machine with flexible and fast ECOFAST or M12
connection methods
Other PROFIBUS I/O
Gateways •DP/AS-Interface link 20E and DP/AS-Interface link Advanced for
the PROFIBUS DP gateway to AS-Interface
•DP/DP coupler for connecting two PROFIBUS DP networks
Drive interfaces •ADI4 (Analog Drive Interface for 4 axes) for connection of drives
with analog ± 10 V setpoint interface or for external encoders
•IM174 (Interface Module for 4 axes) for connection of drives with
analog ± 10 V setpoint interface, for external sensors, or for
connection of stepper drives with pulse-direction interface
Drive units with
PROFIBUS DP interface
(e.g., SINAMICS S120)
... convert speed setpoints into signals for controlling the motor and
supply the power required to operate the motors.
Also can be operated as an isochronous slave on PROFIBUS DP.
Teleservice adapter Remote diagnostics
Ethernet
The control unit can communicate with the following components via the Ethernet interfaces
or be embedded in an automation environment:
Table 1- 3 Components on the Ethernet
Component Function
Programming device (PG/PC) ... configures, parameterizes, programs, and tests with the
"SIMOTION SCOUT" engineering system (ES)
Master computer ... communicates with other devices via UDP, TCP/IP
SIMATIC HMI device ... is used for operating and monitoring functions. This is not an
essential requirement for the operation of a control unit.

Description
1.2 System components
D4x5
Manual, 05/2009 15
PROFINET
The use of a Communication Board Ethernet (CBE30) enables SIMOTION D4x5 to
communicate with the following components via PROFINET:
Table 1- 4 Components on the PROFINET
Component Function
Programming device (PG/PC) ... configures, sets parameters, programs, and tests using the
"SIMOTION SCOUT" Engineering System (ES).
SIMATIC HMI device ... is used for operating and monitoring functions. This is not an
essential requirement for the operation of a Control Unit.
Other controls (e.g. SIMOTION
or SIMATIC)
... e.g. higher-level controller (plant controller); modular machine
concepts with multiple controls, distributed across individual
machine modules
Master computer ... communicates with other devices via UDP, TCP/IP.
Distributed I/O systems
SIMATIC ET 200M Modular I/O system for control cabinet installation and high
channel densities.
SIMATIC ET 200S Finely scalable I/O system for control cabinet installation and
particularly time-critical applications; including motor starters,
safety technology and individual grouping of load groups.
SIMATIC ET 200pro Modular I/O system with IP65/67 rating for machine-related
applications with no control cabinet; with features such as compact
designs, integrated PROFIsafe safety technology, PROFINET
connection and live module replacement.
SIMATIC ET 200eco PN Compact block I/O with IP65/66/67 degree of protection for
cabinet-free usage in machines with M12 connection method. Very
rugged and resistant encapsulated metal enclosure.
Other PROFINET I/O
Drive units with PROFINET
interface
... convert speed setpoints into signals for controlling the motor
and supply the power required to operate the motors.
Gateways •IE/AS-Interface link PN IO for the PROFINET IO gateway to
AS-Interface
•PN/PN coupler for connecting two PROFINET IO networks
DRIVE-CLiQ
The DRIVE-CLiQ interfaces permit a fast connection to the SINAMICS drive components.
DRIVE-CLiQ offers the following advantages within the DRIVE-CLiQ topology rules:
● Expandability of components
● Automatic detection of components by the control unit
● Standardized interfaces to all components
● Uniform diagnostics down to the components
● Complete service down to the components
● Simple mechanical handling
The controller can communicate with the following components via DRIVE-CLiQ:

Description
1.2 System components
D4x5
16 Manual, 05/2009
Table 1- 5 Components connected to DRIVE-CLiQ
Component Function
Control Unit (SINAMICS S120) Central control module in which the open- and closed-loop
control functions for the drive are implemented.
Line Module (SINAMICS S120) ... generates a DC link from the supply system.
Motor Module (SINAMICS S120) ... used to control motors (DC/AC inverters, booksize).
Power Module (SINAMICS S120) ...used to control motors (AC/DC converters, blocksize).
Controller Extension CX32 ... enables additional axes to be connected for SIMOTION D435
and D445/D445-1.
CUA31/CUA32 control unit
adapter
...enables a blocksize power module (PM340) to be connected to
a booksize control unit D4x5, CX32 or CU320.
Terminal Module TM31 ... enables a terminal expansion via DRIVE-CLiQ (additional
analog and digital I/Os).
Terminal Module TM41 ... enables a terminal expansion (analog and digital I/Os) and
encoder simulation.
Terminal Module TM54F ... enables terminal expansion (secure digital inputs/outputs) for
controlling the secure motion monitoring functions of the
integrated drives.
Terminal Module TM15, TM17
High Feature
The terminal modules TM15 and TM17 High Feature are used to
implement inputs of measuring inputs and outputs of cam
outputs. In addition, these terminal modules provide drive-related
digital inputs and outputs with short signal delay times.
SMx sensor modules ... enable acquisition of encoder data from connected motors via
DRIVE-CLiQ.
Motors with DRIVE-CLiQ
interface
...allow simplified commissioning and diagnostics, as the motor
and encoder type are identified automatically.
DMC20 DRIVE-CLiQ Hub …Enables the number of DRIVE-CLiQ interfaces to be increased
and the creation of a star-shaped topology.
Note
You can find detailed information about components in the SINAMICS S120 family of
products in the SINAMICS S120 manuals.
Optional components
The functionality of the D4x5 Control Unit can be expanded by using one of the components
listed below.
Table 1- 6 Optional components
Component Function
Communication Board Ethernet
CBE30
Communication via PROFINET IO with IRT and PROFINET IO
with RT
Terminal Board TB30 Terminal expansion, i.e. additional analog and digital I/O
The selected component is plugged into the option slot of the Control Unit.

Description
1.3 I/O integration
D4x5
Manual, 05/2009 17
1.3 I/O integration
Note
Note that not all modules in the ET 200 I/O family are approved for SIMOTION. Moreover,
system-related functional differences can come into play when these I/O or I/O systems are
used on SIMOTION vs. on SIMATIC. For example, special process-control functions (e.g.,
HART modules, etc.) are not supported by SIMOTION for the ET 200M distributed I/O
system.
A detailed, regularly updated list of the I/O modules approved for use with SIMOTION, as
well as notes on their use, can be found on the Internet at
(http://support.automation.siemens.com/WW/view/en/11886029):
In addition to the I/O modules enabled for SIMOTION, in principle all certified standard
PROFIBUS slaves (DP-V0/DP-V1/DP-V2) and PROFINET IO devices with RT and IRT real-
time classes may be connected to SIMOTION D4x5. These modules are integrated using the
GSD file (PROFIBUS) or GSDML file (PROFINET) provided by the relevant device
manufacturer.
Note
Please note that in individual cases further boundary conditions must be fulfilled in order to
integrate a standard slave/standard device into SIMOTION. Thus, a few modules require
"driver blocks" , e.g., in the form of function blocks, that permit (or simplify) integration.
For modules enabled for SIMOTION (e.g. SIMATIC S7-300 module FM 350-1, etc.), these
driver modules are part of the SIMOTION SCOUT Engineering System command library.

Description
1.4 Representation of SIMOTION D425 and SIMOTION D435
D4x5
18 Manual, 05/2009
1.4 Representation of SIMOTION D425 and SIMOTION D435
The following figure shows the SIMOTION D425 or SIMOTION D435 with its interfaces and
front panel elements (fault and status displays).
;;
'5,9(&/L4LQWHUIDFHV
6KLHOGFRQWDFW
;;
'LJLWDOLQSXWVGLJLWDORXWSXWV
;
(OHFWURQLFSRZHUVXSSO\
;;
(WKHUQHWSRUWV
2SWLRQVORW
;
352),%86'3 ;
352),%86'303,
86%[
OHIW;ULJKW
;
;;
0HDVXULQJVRFNHWV
/('GLVSOD\V
;
(WKHUQHWLQWHUIDFHQR
IXQFWLRQ
6HUYLFHVHOHFWRU
VZLWFK
2SHUDWLQJPRGH
VZLWFK
3RWHQWLDO
FRQQHFWLRQ
5(6(7EXWWRQ
;
)DQEDWWHU\PRGXOH
಻RSWLRQDO
VHJPHQWGLVSOD\
UHOHYDQWIRUVHUYLFHRQO\
;XQGHUVLGH
56QRIXQFWLRQ
6SDFHU
RSWLRQDO
%23LQWHUIDFHQR
IXQFWLRQ
;&RPSDFW
)ODVKFDUG
Figure 1-2 Location of interfaces and front panel elements of SIMOTION D425 and SIMOTION D435
Note
SIMOTION D425 and D435 come with pre-assembled spacers. These can be removed if
necessary.

Description
1.5 Representation of SIMOTION D445
D4x5
Manual, 05/2009 19
1.5 Representation of SIMOTION D445
The following figure shows the SIMOTION D445 with its interfaces and front panel elements
(fault and status displays).
;;
'5,9(&/L4LQWHUIDFHV
6KLHOGFRQWDFW
;;
'LJLWDOLQSXWVGLJLWDORXWSXWV
;
(OHFWURQLFSRZHUVXSSO\
;;
(WKHUQHWSRUWV
2SWLRQVORW
&RROLQJILQV
6SDFHUVDOZD\V
UHTXLUHG
;
352),%86'3
;
352),%86'303,
86%[
ULJKW;
OHIW;
;
&RPSDFW)ODVKFDUG
;
)DQEDWWHU\PRGXOH
/('GLVSOD\V
VHJPHQWGLVSOD\
UHOHYDQWIRUVHUYLFHRQO\
;XQGHUVLGH
56QRIXQFWLRQ
5(6(7EXWWRQ
0RGHVHOHFWRUVZLWFK
3RWHQWLDOFRQQHFWLRQ
;;
0HDVXULQJVRFNHWV
%23LQWHUIDFHQR
IXQFWLRQ
6HUYLFHVHOHFWRUVZLWFK
(WKHUQHWLQWHUIDFHQR
IXQFWLRQ
Figure 1-3 Location of interfaces and front panel elements of SIMOTION D445

Description
1.5 Representation of SIMOTION D445
D4x5
20 Manual, 05/2009
CAUTION
SIMOTION D445 must be operated with a fan / battery module for heat dissipation. Without
a fan/battery module, the control unit will not start up and cannot be commissioned.
A description of how to install the fan/battery module can be found in "Spare
Parts/Accessories" Installing the fan/battery module (Page 70).
Note
The spacers cannot be removed in the case of the SIMOTION D445.