Siemens Flowrite 599 Series Owner's manual

Flowrite™ 599 Series
Technical Instructions
Document No. 155-180P25
EA 599-4
February 28, 2018
SKD6xU Electronic Valve
Actuators
24 Vac Proportional Control
Siemens Industry, Inc.
Description The Flowrite 599 Series SKD6xU Electronic Valve Actuators require a 24 Vac supply
and receive a 0 to 10 Vdc or a 4 to 20 mA control signal to proportionally control a
valve. These actuators are designed to work with Flowrite 599 Series valves with a 3/4-
inch (20 mm) stroke.
Features •Direct-coupled installation requires no special tools or adjustments
•Visual and electronic stroke indication
•Die-cast aluminum housing
•Manual override
•Spring return to fail-safe position or non-spring return fail-in-place
•Automatic stroke calibration
•Maintenance-free
Application These electronic actuators are designed to be used with Flowrite 599 Series valves and
Siemens Industry standard valves with a 3/4-inch (20 mm) stroke in liquid service
applications.
CAUTION:
Do not use in low pressure steam applications.
Product Number SKD62U, Spring Return (Actuator Prefix Code 274)
SKD60U, Non-Spring Return (Actuator Prefix Code 267)
Warning/Caution Notations
WARNING: Personal injury or loss of life may occur if you
do not perform a procedure as specified.
CAUTION: Equipment damage or loss of data may occur
if you do not perform a procedure as
specified.

Technical Instructions SKD6xU Electronic Valve Actuators 24 Vac Proportional Control
Document Number 155-180P25
February 28, 2018
Page 2 Siemens Industry, Inc.
Specifications
Power supply Operating voltage 24 Vac -20%/+30%
Frequency 50/60 Hz
Power consumption 17 VA/12W
Control signals Control input (Y)
Voltage 0 to 10 Vdc or 4 to 20 mA
(DIP switch selectable)
Maximum Impedance 0 to 10 Vdc 100K ohms
4 to 20 mA; 240 ohm
Signal resolution <1%
Hysteresis 1%
Control input (Z)
Resistance 0 to 1000 ohms
Voltage 0 to 1.6V
Control output (U) – position feedback
Voltage 0 to 9.8 Vdc + 2%
Load Impedance >10K ohm
Current 4 to 19.6 mA + 2%
Load impedance < 500 ohms
Function Nominal stroke 3/4-inch (20 mm)
Run time with control operation (full stroke)
Pushing stroke, 0 to 100% 30 seconds
Pulling and Spring return stroke, 100 to 0% 15 seconds
Nominal Force Stroke Force
NC and 3-way upper 0% 225 lbs (1000 N)
NO and 3-way by-pass 100% 258 lbs (1150 N)
Agency Certification UL approval UL873
cUL Certified to Canadian standard
C22.2 No. 24-93
conformity per the EMC directive 89/336/EEC
Low voltage directive 73/23/EEC
Ambient conditions Ambient temperature (Operation) 5°F to 122°F (-15°C to 50°C)
Media temperature -13°F to 300°F (-25°C to 150°C)
<32°F (0°C) requires a Stem Heater
Housing NEMA Rating NEMA 1 (interior only)
See Accessories.
Miscellaneous Dimensions See Figure 17
Conduit opening 1/2-inch NPSM
Weight
SKD60U 7.9 lbs (3.6 kg)
SKD62U 8.5 lbs (3.85 kg)

SKD6xU Electronic Valve Actuators 24 Vac Proportional Control Technical Instructions
Document Number 155-180P25
February 28, 2018
Siemens Industry, Inc. Page 3
Accessories NOTE:Installation instructions are included with each accessory.
Figure 1. Auxiliary Switch.
ASC1.6 Auxiliary switch.
Sends a signal to indicate the valve is in
the 0% stroke position. Switching point is
fixed at the 0% stroke position.
Switching capacity 24 Vac
4A resistive
2A inductive
Lowest recommended
current 10 mA
Figure 2. Packing Heating Element.
599-00417 Packing heating element.
Allows stem to move freely in valves
controlling fluids at temperatures below
32°F (0°C). Reduces ice crystal formation
on the stem which may damage the
packing.
Operating Voltage 24 Vac
Heating Output 20 W
Figure 3. Weather Shield.
599-10071 Weather Shield.
See Service Kits for replacement ultraviolet
resistant cable ties.
Service Kits The only field serviceable part is the circuit board.
Circuit board replacement 4-668-5748-8
Plastic wiring compartment cover 4-104 5634-8
Manual Override Kit for SKD 4-268 5504-8
Ultraviolet (UV) resistant cable ties (pkg. of 10) 538-996
WARNING:
This product contains a spring under high compression. Do not attempt to
disassemble the actuator.

Technical Instructions SKD6xU Electronic Valve Actuators 24 Vac Proportional Control
Document Number 155-180P25
February 28, 2018
Page 4 Siemens Industry, Inc.
SKD Details
Figure 4. SKD6xU Details.
Legend
1 Pressure cylinder
2 Piston
3 Oscillating pump
4 Return spring
5 Bypass valve
6 Valve stem retainer
7 Manual override knob
8 Position indicator
Operation The actuator accepts a 0 to 10 Vdc or a 4 to 20 mA control signal. The actuator
mounted on a valve, produces a stroke proportional to the input signal. When power is
turned off or in the event of a power failure, the SKD62U Actuator spring returns the
valve to its normal position, and the SKD60U Actuator fails in place.
Figure 5. Figure 6.
Spring return: When power is turned off or
in the event of a power failure, the actuator
spring returns the valve to its normal
position.
Non-spring return: When power is turned
off or in the event of a power failure, the
actuator maintains its position.
Figure 7. Valve Stem Travel Indication.

SKD6xU Electronic Valve Actuators 24 Vac Proportional Control Technical Instructions
Document Number 155-180P25
February 28, 2018
Siemens Industry, Inc. Page 5
Mounting and
Installation
Figure 8. Acceptable Mounting Positions.
The vertical position is the recommended position for mounting. Other positions are
allowed. When using the Weather Shield for NEMA 3R rating, the vertical position is
required. See Weather Shield installation instructions and Figure 8.
Allow four inches (100 mm) around the sides and back of the actuator and eight inches
(200 mm) above and to the front of the actuator.
See dimensions in Figure 17.
Detailed installation instructions for field mounting are shipped with the actuator.
Start-up Check the wiring for proper connections.
NOTE:The valve body assembly determines the complete assembly action.
Stroke Calibration To determine the stroke positions 0% and 100% in the valve, calibration is required
when the valve/actuator are commissioned for the first time.
The actuator must be mechanically connected to a valve and must have a 24 Vac
power supply. The calibration procedure can be repeated as often as necessary.
CAUTION:
Before starting calibration, be sure the manual adjuster
is set to Automatic to register the actual values.
There is a slot on the printed circuit boards of the actuators. To
initiate the calibration procedure, the contacts inside this slot
must be short-circuited, for example, with a screwdriver
(see Figure 9).
Automatic calibration proceeds as follows (see Figure 10):
•Actuator runs to the 0 stroke position (1), green LED flashes.
•Actuator then runs to the 100 stroke position (2), green LED
flashes.
•Measured values are stored in the EPROM.
•The actuator now moves to the position defined by control
signal Y or Z (3), and the green LED now glows steadily
(normal operation).
•Throughout this procedure, output U is inactive; meaning,
the values only represent actual positions when the green
LED stops flashing and remains on continuously.
Figure 9.
Figure 10.

Technical Instructions SKD6xU Electronic Valve Actuators 24 Vac Proportional Control
Document Number 155-180P25
February 28, 2018
Page 6 Siemens Industry, Inc.
Stroke Calibration,
Continued Table 1. LED Status.
LED Display Function Action
Green ON Normal Operation Automatic operation
Flashing Stroke calibration In Progress Wait for calibration to be
completed (LED stops flashing)
Red
ON
Faulty stroke calibration
Internal Error
- Check mounting
- Restart stroke calibration (by
short-circuiting calibration slot)
- Replace electronics
Flashing Inner valve jammed Check the valve
OFF •No power supply
•Faulty electronics -Check mains
-Replace electronics
Override Control The override control input (Z) has three modes of operation:
The Z-modes have a "direct acting" factory setting.

SKD6xU Electronic Valve Actuators 24 Vac Proportional Control Technical Instructions
Document Number 155-180P25
February 28, 2018
Siemens Industry, Inc. Page 7
Start-up, Continued
1 2
Figure 11. SKD Electronic Features.
DIP Switches
(Left to right)
1
Selection of
Control Signal
2
Selection of
Flow Characteristic
ON 4 to 20 mA Modified*
OFF
Factory Setting 0 to 10 Vdc Default
*Changing the default setting will modify an equal percentage valve to a linear flow
characteristic. When set to default, the flow characteristic is determined by the valve body.
Normally Closed Valve Actuator pressure cylinder moves:
•Outward (0 to 1): Valve opens.
•Inward (1 to 0): Valve closes.
Normally Open Valve Actuator pressure cylinder moves:
•Outward (0 to 1): Valve closes.
•Inward (1 to 0): Valve opens.
Three-Way Valve Actuator pressure cylinder moves
•Outward (0 to 1): Valve opens between port NC and C.
•Inward (1 to 0): Valve opens between ports NO and C.
The measuring voltage at terminal U provides valve stem position feedback to an
indicating instrument or building automation system.

Technical Instructions SKD6xU Electronic Valve Actuators 24 Vac Proportional Control
Document Number 155-180P25
February 28, 2018
Page 8 Siemens Industry, Inc.
Manual Operation
Figure 12. The Manual Setting Knob in Manual and Automatic Position.
- Turn the manual setting knob clockwise for manual operation.
- A red indicator becomes visible as you begin to crank. Each complete revolution
(360°) is equal to 3/32-inch (2.5 mm) stroke.
- If a signal is sent to the actuator while it is in manual operation, the actuator will
move but the control will not be accurate.
- The valve cannot be commanded to its 0% position while in manual operation.
Automatic operation For automatic operation the manual override knob must be in the fully closed position.
Turn the manual override knob counterclockwise until the red indicator disappears.
Wiring Do not use autotransformers. Use earth ground isolating step-down Class 2 power
supplies.
Determine supply transformer rating by summing total VA of all actuators used.
The maximum rating for Class 2 step-down transformer is 100 VA.
•Since SKD6xU actuators require ≈20 VA, a maximum of four actuators can be
powered by one transformer (80% of transformer VA).
•Operating more than four SKD6xU actuators requires additional transformers or
separate 100 VA power supplies.
•The position output signal U will switch from 0 to 10 Vdc to 4 to 20 mA when a 4
to 20 mA input signal is selected and used on the Y terminal.

SKD6xU Electronic Valve Actuators 24 Vac Proportional Control Technical Instructions
Document Number 155-180P25
February 28, 2018
Siemens Industry, Inc. Page 9
Wiring Diagrams
Figure 13. Connecting Terminals.
24 Vac
G System Potential (SP)
G0 System Neutral (SN)
Y Control input 0 to 10 Vdc or 4 to 20 mA (DIP switch selectable)
M Measuring neutral
U Position indication 0 to 10 Vdc or 4 to 20 mA, (see Table 2.
Z Override control
Table 2.
Actuator input signal
Receiving Impedance
Low (<500
Ohm) High (>10K Ohm)
0 to 10 Vdc 0 to 20 mA 0 to 10 Vdc
4 to 20 mA 4 to 20 mA 2 to 10 Vdc
Figure 14. Auxiliary Switch ASC1.6. Figure 15. Packing Heating Element
599-00417.
Troubleshooting Check that the wires are connected correctly and attached securely.
Check for adequate power supply.
Check that the actuator is set for automatic operation. See the Start-Up section.

Technical Instructions SKD6xU Electronic Valve Actuators 24 Vac Proportional Control
Document Number 155-180P25
February 28, 2018
Page 10 Siemens Industry, Inc.
Dimensions
Figure 16. Dimensions of 599-10071 Weather Shield in Inches (Millimeters).