Siemens ICP-B6 Service manual

To Set the ICP-B6 Module Address:
1. Plug the programming cable of the DPU or
FPI-32 Programmer/Tester (SensorLINK)
into the two-pin receptacle on the ICP-B6.
(See Figure 2 for location only.)
2. Set the system address for the ICP-B6 by
following the instructions in the FPI-32
(SensorLINK) Programmer/Tester Manual,
P/N 315-090077, or the DPU User's
Manual, P/N 315-033260, as applicable.
Removeallsystempowerbeforeinstalla-
tion, first battery and then AC. (To power
up, connect the AC first, then the battery.)
All wiring must comply with
national and local codes.
The ICP-B6 should be installed in a UL
listed electrical box. (See Figure 10.)
Analog Loop
The ICP-B6 communicates with the MXL
through its analog addressable loops. These
loops are on either the MMB or on the op-
tional ALD-2I module of the MOM-4. They
may be wired for Class A (Style 6) or Class B
(Style 4). Figure 1 shows both wiring types
and the connections to either the MMB or to
the MOM-4 when the ALD-2I module is used.
The table on the following page lists the
maximum output currents allowed.
Installation Instructions
MODEL ICP-B6
Intelligent Control Point
The Model ICP-B6 Intelligent Control Point from
Siemens Industry, Inc. can be used as an
independent, remotely located telephone zone, a
speaker zone (25V or 70.7V RMS), or notification
appliance circuit (NAC), depending on how it is
configured. It communicates through the analog
loop of the MXL/MXLV System.
OPERATION
Up to 12 ICP-B6s can connect to each analog
loop of the MXL/MXLV. These modules must
be connected to the first 12 address locations
on the analog loop.
The 24 VDC power input for each ICP-B6
comes from either the MMB, the PSR, or from
an auxiliary power supply which is power
limited and UL listed for fire protective signal-
ing use and is rated between 24 and 27.3
VDC. Each ICP-B6 can be assigned a 32-
character, custom alphanumeric message.
Each module uses one address on either the
analog loop of the ALD-2I module or the analog
loop of the MMB board. (See Figure 1) The
ICP-B6 is programmable for different usages.
For additional information on the MXL/MXLV
System, refer to the MXL/MXLVManual, P/N
315-092036.
Addressing and Testing
Use the DPU Device Programming Unit or the
FPI-32 Programmer/Tester (SensorLINK) to
program and test the module.
NOTE: With FPI-32 Rev. 1.3 software, only
1=MXL mode should be used when
programming a device.
P/N 315-095306-10
Siemens Industry, Inc.
Building Technologies Division
Florham Park, NJ
Siemens Building Technologies, Ltd.
Fire Safety & Security Products
2 Kenview Boulevard
Brampton, Ontario
L6T 5E4 Canada

2
The ICP-B6 module can be used in four
different ways:
1. Using the ICP-B6 as an NAC Module
This notification appliance application uses the
principle of polarity reversal when there is an
alarm. Figure 2 shows the polarity connection
in a supervisory condition. When using the
ICP-B6 as a supervised NAC output module
with notification appliance devices, cut jumper
JP2. Refer to Figure 2 for additional connec-
tion and jumper information, and to P/N 315-
096363 for a list of compatible devices.
MAXIMUM ALLOWABLE ICP-B6 OUTPUT CIRCUIT LINE RESISTANCE
FOR SPECIFIED DC RISER CURRENT AND LINE RESISTANCE
MAXIMUM
DC RISER
CURRENT
(in Amps)
DC RISER RESISTANCE (in Ohms)
0.1 Ohm 0.25 Ohm 0.5 Ohm 0.75 Ohm 1 Ohm 1.5 Ohms
82.46 1.67 .33 -- -- --
72.53 1.83 .66 -- -- --
62.60 2.00 1.00 -- -- --
52.67 2.16 1.33 .5 -- --
42.73 2.33 1.67 1.00 .33 --
32.80 2.50 2.00 1.50 1.00 --
22.86 2.67 2.33 2.00 1.67 1.00
12.93 2.83 2.67 2.50 2.33 2.00
.5 2.96 2.92 2.83 2.75 2.67 2.50
MAXIMUM LOOP RESISTANCE FOR EACH ICP-B6 ON RISER
NOTES:
1. Resistances specified are for both wires.
2. If higher currents are required, Siemens Industry, Inc. recommends using a local auxiliary
supply which is UL listed for fire protection signaling use. The supply should be rated between
24 and 27.3 VDC.
When used as an NAC module, the output
circuit is power limited. The ICP-B6 maximum
current is 1.5A at 24 VDC. If the 24 VDC is
lost or the NAC line is broken or shorted, the
trouble condition INPUT DEVICE RESPONSE
TOO LOW displays at the MXL/MXLV control
panel. Refer to Figures 3 and 4 for the con-
nections used with the TRI-60/B6 module and
the PSR-1 module, respectively. See the Line
Resistance chart for the allowable line
resistance for each ICP-B6 output circuit.
ELECTRICAL RATINGS
tnerruCeludoMCDV5evitcAAm0
tnerruCeludoMCDV42evitcAAm01
tnerruCeludoMCDV42ybdnatSAm01

3
Figure 2
ICP-B6 Used as a Strobe Module
++
+
+
+
+
-
-
-
-
--
POWER
LIMITED
STYLE Y STYLE Z
15K, 1/2W, 5% EOL RESISTOR
P/N 140-820400
15K, 1/2W, 5%
EOL RESISTOR
P/N 140-820400
SUPERVISED STROBE ACTIVATION - SPECIAL APPLICATION
SUPV: 9VDC, .5mA
ACTIVATED: 16-32V UNFILTERED FULL WAVE RECTIFIED, 1.5A MAX
POLARITY SHOWN IN SUPV. CONDITION
ICP-B6 MODULE IS USED FOR
NAC SUPERVISION AND ACTIVATION
NOTES:
1. ALL WIRING MUST COMPLY WITH NATIONAL AND LOCAL CODES.
2. POSITIVE AND NEGATIVE GROUND FAULT DETECTED AT <5K OHMS FOR TERMINALS 3-6.
3. FOR SYNCHRONIZATION OF NOTIFICATION APPLIANCES USE EITHER DSC, DSC-W, OR PAD-3.
ICP-B6 MODULE IS USED FOR
NAC SUPERVISION AND ACTIVATION
16-32 VDC
NAC UNITS
SEE TABLE 1
DC INPUT RATED
24 - 27.3 VDC FWR
SUPV: 12mA
ACTIVATED: 1.5A MAX
24-27.3 VDC, 18mA MAX
9 VDC, 0.5mA
SPECIAL APPLICATION
16-32V UNFILTERED FULL WAVE RECTIFIED
1.5A, POWER LIMITED
+ + - -
ICP-B6 ICP-B6
PROGRAM
PLUG
PROGRAM
PLUG
TB2
TB1 TB1
6
6 6
5
5 5
4
4 4
3
3 3
2
2 2
1
1 1
++++
----
ANALOG
LOOP
CONNECTION
SUPERVISED
MODULE INPUT SUPPLY
FROM PS-35, PSR-1, OR
UL LISTED POWER SUPPLY
MANUFACTURED BY
ALARM-SAF (Model BN4-002-UL)
ELECTRICAL:
INPUT DC SUPPLY:
SUPERVISORY OUTPUT:
ACTIVATED:
JP2 JP2
JP1 JP1
EARTH
SHIELD
+ + - -
TB2 654321
EARTH
SHIELD
Figure 1
Analog Loop Connections
100 OHMS MAX
ANALOG LOOP CONNECTION
(T-TAPPING ALLOWED)
OPERATES IN FULL CONFORMANCE WITH STYLE 4 (CLASS B)
*JUMPERS CAN BE REMOVED FROM MMB-3 WITH CSGM CONFIGURATION
*
*
TB1 TB1 TB1
ICP-B6 ICP-B6 ICP-B6
12 12 12
ALD-2I ALD-2I
MOM-4
TB2 MOM-4 TB1 MMB TB2 MMB TB3
LOOP 1 LOOP 2 LOOP 1 LOOP 2 LOOP 1 LOOP 2
4
3
2
1
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
4
3
2
1
4
3
2
1
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
4
3
2
1
LOOP RESISTANCE 100 OHMS MAX
18 AWG MINIMUM WIRE
NO EOL DEVICE REQUIRED
SUPERVISED, POWER LIMITED PER NEC 760
ALL WIRING MUST CONFORM TO NATIONAL AND
LOCAL ELECTRICAL CODES

4
Figure 4
ICP-B6 Connections Using PSR-1
Figure 3
ICP-B6 Connections When Using TRI-60/B6

5
2. Using the ICP-B6 as a Telephone Zone
When the ICP-B6 is used as a telephone zone
module, the 24 VDC provides supervision,
trouble, and call-in conditions. If the 24 VDC is
lost, the trouble condition INPUT DEVICE
RESPONSE TOO LOW displays at the MXL/
MXLV and an LED for that zone lights at the
VSM-1 module.
The supervised telephone common talk riser
starts at the TBM module in the MME-3 back-
box. The Class B shielded cable connects
continuously to each ICP-B6 with a 5.6K end of
line device. Tie the shield of these riser wires
and the shield of the zone output wires together
using terminal 5 of TB2 and isolate them from
the system circuits and the earth ground.
Connect the supervised individual zone output
connections from each ICP-B6 to the field
telephone with shielded cable. Terminate
them at the last station with a 10K ohm end of
line resistor. As with the common talk line
described in the paragraph above, be sure
that the shield is continuous and isolated
Figure 5
ICP-B6 Used as a Telephone Zone
+
+
+
+
+
-
-
-
-
-
ANALOG LOOP
CONNECTION
FJ-303
FJ-303
BLACK
BLACK BLACK
BLACK
WHITE WHITE WHITE WHITE
SHIELD
SHIELD
SHIELD
WARDEN'S STATIONS
MODELS FT-301 SERIES
AND FT-302 SERIES
24 OHMS MAX
10K, 1/2W, +/-5%
EOL RESISTOR
P/N 140-112172
AT LAST STATION
ICP-B6 DC SUPPLY
FROM MMB, PSR-1, OR
UL LISTED POWER SUPPLY
MANUFACTURED BY ALARM-SAF
Model BN4-002-UL (SUPERVISED)
FROM PREVIOUS ICP-B6, OCC-1,
OR TBM
(20 OHMS MAXIMUM
LINE RESISTANCE)
COMMON TALK RISER
18 AWG MINUMUM
BELDON 8760 OR EQUIVALENT
OR AS REQUIRED BY
THE LOCAL AUTHORITY
HAVING JURISDICTION
RISER
NOMINAL VOLTAGE:
MAXIMUM CURRENT:
17.5 VDC
175 mA
10K, 1/2W, +/-5%
EOL RESISTOR
P/N 140-112172
AT LAST FJ-303
5.6K, 1/2W, +/-5%
EOL RESISTOR
ELECTRICAL:
INPUT DC SUPPLY:
SUPERVISORY OUTPUT:
ACTIVATED OUTPUT:
20.5 TO 30 VDC, 18mA MAX
8V, .8mA
11V, 70mA
SUPERVISED
POWER LIMITED
FROM MXL MMB OR
ALD-2I ON MOM-4
(12 MAX ICP-B6
MODULES PER LOOP)
(SUPERVISED)
NOTES:
1. THE SHIELD ON THE COMMON TALK LINE MUST BE CONTINUOUS
AND CONNECTED ONLY TO DC COMMON AT CONTROL PANEL.
2. ALL WIRING MUST CONFORM TO NATIONAL AND LOCAL CODES.
3. POSITIVE AND NEGATIVE GROUND FAULT DETECTED AT <5K OHMS FOR TERMINALS 3-6.
ICP-B6 ICP-B6
PROGRAM
PLUG
PROGRAM
PLUG
TB1 TB1
6 6
5 5
4 4
3 3
2 2
1 1
++++
----
JP2 JP2
JP1 JP1
SHIELD SHIELD SHIELD
SHIELD
SHIELD
+
+
-
-
TB2
654321
SHIELD
TO
EARTH
+
+
+
-
-
-
TB2
654321
SHIELD
TO
EARTH
from both system circuits and earth
ground and that the shields are connected
together using terminal 5 of TB-2.
3. Using the ICP-B6 as a 70 Volt Speaker
Zone
When the ICP-B6 is used as a speaker zone,
the 24 VDC provides the supervision. If the 24
volts is lost or there is an open or shorted
speaker output line, the trouble condition
INPUT DEVICE RESPONSE TOO LOW
displays at the MXL/MXLV and the related
zone LED on the VSM-1 lights.
The 70.7V RMS audio input comes from the
amplifier via the ASC-2 Amplifier Supervision
card. The ASC-2 supervises the audio con-
nection path to the ICP-B6 and provides up to
100 watts of power. The ASC-2 can be used
as Style Y (Class B) or Style Z (Class A). Refer
to the ASC-2 Instructions, P/N 315-092085.
When the ICP-B6 is used as a speaker zone,
the output speaker lines are supervised and
power limited. The audio output cannot exceed

6
25 watts. Connect the speaker output as either
Style Y (Class B) or Style Z (Class A). Figure 6
gives the approximate decibel loss for the total
speaker zone wire length for various wire
gauge sizes.
When using the ICP-B6 as a 70.7V RMS
speaker zone, cut the JP1 jumper. (See
Figure 8.)
4. Using the ICP-B6 as a 25 Volt Speaker
Zone
When the ICP-B6 is used as a speaker zone,
the 24 VDC provides the supervision. If the 24
volts is lost or there is an open or shorted
speaker output line, the trouble condition
INPUT DEVICE RESPONSE TOO LOW
displays at the MXL/MXLV and the related
zone LED on the VSM-1 lights.
The 25V RMS audio input comes from the
amplifier via the ASC-2 Amplifier Supervision
card. The ASC-2 supervises the audio con-
nection path to the ICP-B6 and provides up to
100 watts of power. The ASC-2 can be used
as Style Y (Class B) or Style Z (Class A).
Refer to the ASC-2 Instructions, P/N 315-
092085.
When the ICP-B6 is used as a speaker zone,
the output speaker lines are supervised and
power limited. The audio output cannot
exceed 35 watts. Connect the speaker output
as either Style Y (Class B) or Style Z (Class
A). Figure 7 gives the approximate decibel
loss for the total speaker zone wire length for
various wire gauge sizes.
When using the ICP-B6 as a 25V RMS
speaker zone, cut the JP2 jumper (See
Figure 9).
Figure 6
Approximate Speaker Zone Wire Loss
with the 70.7V Option
Figure 7
Approximate Speaker Zone Wire Loss
with the 25V Option

7
ASC-2
ASC-2
15K, 1/2W, 5%
EOL RESISTOR
P/N 140-820400
15K, 1/2W, +/-5%
EOL RESISTOR
P/N 140-820400
15K, 1/2W, 5%
EOL RESISTOR
P/N 140-820400
STYLE Z
SUPERVISED
SPEAKER ZONE CONNECTIONS
SUPV: 9 VDC, 0.5 mA
ACTIVATED: 70.7 VRMS, 25 W MAX
STYLE Y
SUPERVISED
SPEAKER ZONE CONNECTIONS
SUPV: 9 VDC, 0.5 mA
ACTIVATED: 70.7 VRMS, 25 W MAX
16
16
17
17
18
18
19
19
+++
+
+
+
-- -
-
-
-
24K, 1/2 W, +/-5%
EOL RESISTOR
ON LAST ICP-B6
SPEAKER ZONE
MODULE
P/N 140-820405
24K, 1/2 W, +/-5%
EOL RESISTOR
P/N 140-820405
ORIGINAL NFPA STYLE Z
AUDIO RISER CONNECTIONS
TO ICP-B6 ZONE MODULES
FIRST ICP-B6 LAST ICP-B6
ASC-2 RISER CAN NOT
BE T-TAPPED
70.7 VRMS SPEAKER UNITS:
ANY UL LISTED FIRE
PROTECTION SIGNALING
SPEAKER RATED 70.7 V
IS COMPATIBLE WITH
THIS CIRCUIT
10 OHMS MAX
CAPACITOR
COUPLED
70.7 VRMS
SPEAKERS
SUPERVISED BY ICP-B6 MODULES
SUPERVISED
RISER
OBSERVE
CONNECTION
POLARITY
NFPA STYLE Y
AUDIO RISER CONNECTIONS
SUPERVISORY: 9 VDC, 0.5mA
AUDIO OUTPUT: 70.7 VRMS,
100 WATTS MAX
SHIELD
100 OHMS MAX
MAXIMUM OF 12 ICP-B6
MODULES PER LOOP
SEE MXL MANUAL
(P/N 315-092036)
SUPERVISED ANALOG
LOOP CONNECTION
FROM MXL, MMB,
OR ALD-2I ON MOM-4
JP1 JP1
ICP-B6
PROGRAM
PLUG
TB1
6
5
4
3
2
1
++
--
JP2
JP1
ICP-B6
PROGRAM
PLUG
TB1
6
5
4
3
2
1
++
--
JP2
JP1
ICP-B6
PROGRAM
PLUG
TB1
6
5
4
3
2
1
++
--
JP2
JP1
All wiring must comply with national and local codes.
ELECTRICAL:
INPUT DC SUPPLY:
SUPERVISORY OUTPUT:
ACTIVATED OUTPUT:
24-27.3 VDC, 18mA MAX
9 VDC MAX, 0.5mA
70.7 V, 25 WATTS MAX
ICP-B6 DC SUPPLY FROM MMB, PSR-1,
OR UL LISTED POWER SUPPLY
MANUFACTURED BY ALARM-SAF
(Model BN4-002-UL)
DC INPUT RATING
24-27.3 VDC, 18 mA
+ + - -
TB2 654321
SHIELD
EARTH
+ + - -
TB2 654321
SHIELD
EARTH
+ + - -
TB2 654321
SHIELD
EARTH
+ + - -
TB2 654321
SHIELD
EARTH
+ + - -
TB2 654321
SHIELD
EARTH
ASC-2
ASC-2
15K, 1/2W, 5%
EOL RESISTOR
P/N 140-820400
15K, 1/2W, +/-5%
EOL RESISTOR
P/N 140-820400
15K, 1/2W, 5%
EOL RESISTOR
P/N 140-820400
STYLE Z
SUPERVISED
SPEAKER ZONE CONNECTIONS
SUPV: 9 VDC, 0.5 mA
ACTIVATED: 25 VRMS, 35 W MAX
STYLE Y
SUPERVISED
SPEAKER ZONE CONNECTIONS
SUPV: 9 VDC, 0.5 mA
ACTIVATED: 25 VRMS, 35 W MAX
16
16
17
17
18
18
19
19
+++
+
+
+
-- -
-
-
-
24K, 1/2 W, +/-5%
EOL RESISTOR
ON LAST ICP-B6
SPEAKER ZONE
MODULE
P/N 140-820405
24K, 1/2 W, +/-5%
EOL RESISTOR
P/N 140-820405
ORIGINAL NFPA STYLE Z
AUDIO RISER CONNECTIONS
TO ICP-B6 ZONE MODULES
FIRST ICP-B6 LAST ICP-B6
ASC-2 RISER CAN NOT
BE T-TAPPED
25 VRMS SPEAKER UNITS:
ANY UL LISTED FIRE
PROTECTION SIGNALING
SPEAKER RATED 25 V
IS COMPATIBLE WITH
THIS CIRCUIT
10 OHMS MAX
CAPACITOR
COUPLED
25 VRMS
SPEAKERS
SUPERVISED BY ICP-B6 MODULES
SUPERVISED
RISER
OBSERVE
CONNECTION
POLARITY
NFPA STYLE Y
AUDIO RISER CONNECTIONS
SUPERVISORY: 9 VDC, 0.5mA
AUDIO OUTPUT: 25 VRMS,
100 WATTS MAX
SHIELD
100 OHMS MAX
MAXIMUM OF 12 ICP-B6
MODULES PER LOOP
SEE MXL MANUAL
(P/N 315-092036)
SUPERVISED ANALOG
LOOP CONNECTION
FROM MXL, MMB,
OR ALD-2I ON MOM-4
JP1 JP1
ICP-B6
PROGRAM
PLUG
TB1 6
5
4
3
2
1
++
--
JP2
JP1
ICP-B6
PROGRAM
PLUG
TB1 6
5
4
3
2
1
++
--
JP2
JP1
ICP-B6
PROGRAM
PLUG
TB1 6
5
4
3
2
1
++
--
JP2
JP1
All wiring must comply with national and local codes.
ELECTRICAL:
INPUT DC SUPPLY:
SUPERVISORY OUTPUT:
ACTIVATED OUTPUT:
24-27.3 VDC, 18mA MAX
9 VDC MAX, 0.5mA MAX
25 V, 35 WATTS MAX
ICP-B6 DC SUPPLY FROM MMB, PSR-1,
OR UL LISTED POWER SUPPLY
MANUFACTURED BY ALARM-SAF
(Model BN4-002-UL)
DC INPUT RATING
24-27.3 VDC, 12 mA
+ + - -
TB2 654321
SHIELD
EARTH
+ + - -
TB2 654321
SHIELD
EARTH
+ + - -
TB2 654321
SHIELD
EARTH
+ + - -
TB2 654321
SHIELD
EARTH
+ + - -
TB2 654321
SHIELD
EARTH
Figure 8
ICP-B6 Used as a 70.7V Speaker Zone
Figure 9
ICP-B6 Used as a 25V Speaker Zone

MOUNTING
(See Figure 10)
1. Use a standard 3 1/2-inch deep, double
gang electrical switchbox or a 4-inch
square electrical box that is 2 1/2inches
deep with either a 1 1/2-inch deep
extension or a 1 1/4 -inch deep plaster ring
extension.
2. Connect the field wiring. Insert the ICP-B6
into the box and fasten the module plate
to the box.
Figure 10
Mounting the ICP-B6
NOTE: When using the double gang
switchbox or the plaster ring
extension, use the same four
screws to fasten both the mod-
ule and the blank plate (user
supplied).
3. Cover the module front plate with a 4-inch
blank plate (user supplied) and fasten
with two plate screws.
P/N 315-095306-10
Siemens Industry, Inc.
Building Technologies Division
Florham Park, NJ
Siemens Building Technologies, Ltd.
Fire Safety & Security Products
2 Kenview Boulevard
Brampton, Ontario
L6T 5E4 Canada