Siemens SIMATIC IPC647D User manual

SIMATIC IPC647D
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
SIMATIC
Industrial PC
SIMATIC IPC647D
Operating Instructions
01/2014
A5E32996306
-AA
Preface
Overview
1
Safety Instructions
2
Installing and connecting the
device
3
Commissioning the device
4
Extended device functions
5
Expanding and assigning
parameters to the device
6
Device maintenance and
repair
7
Technical specifications
8
Technical support
A
Abbreviations
B
Additional information
"BIOS Description" Operating Manual:
Detailed description of the BIOS setup and the setup parameters
"SIMATIC IPC647D/847D Hardware RAID Configuration" Compact Operating Instructions:
Detailed description of the Hardware RAID systems

Siemens AG
Industry Sector
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E32996306-AA
Ⓟ
01/2014 Technical data subject to change
Copyright © Siemens AG 2014.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by
personnel qualified
for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

SIMATIC IPC647D
Operating Instructions, 01/2014, A5E32996306-AA 3
Preface
These operating instructions contain all the information you need for commissioning and
operation of the SIMATIC IPC647D .
It is intended both for programming and testing personnel who commission the device and
connect it with other units (automation systems, programming devices), as well as for service
and maintenance personnel who install add-ons or carry out fault/error analyses.
Basic knowledge required
A solid background in personal computers and Microsoft operating systems is required to
understand this manual. General knowledge in the field automation control engineering is
recommended.
Validity of the Operating Instructions
These operating instructions are valid for all supplied versions of the SIMATIC IPC647D.
Scope of this documentation
The documentation for the SIMATIC IPC647D includes the following sections:
●Product Information "Important notes on your device"
●Quick Install Guide SIMATIC IPC647D
●SIMATIC IPC647D operating instructions in English and German
The documentation is part of the "Documentation and Drivers" DVD supplied with the
product.
Refer to the corresponding user documentation for information and instructions on using
software.
Conventions
The terms "PC" or "device" are sometimes used in place of the product name
SIMATIC IPC647D in these operating instructions.
History
Currently released versions of these operating instructions:
Version
Comments
01/2014
First edition

Preface
SIMATIC IPC647D
4Operating Instructions, 01/2014, A5E32996306-AA

SIMATIC IPC647D
Operating Instructions, 01/2014, A5E32996306-AA 5
Table of contents
Preface ................................................................................................................................................... 3
1 Overview................................................................................................................................................. 9
1.1 Product description ........................................................................................................................9
1.1.1 Highlights .....................................................................................................................................10
1.1.2 Features .......................................................................................................................................11
1.2 Design of the device ....................................................................................................................15
1.2.1 Device views ................................................................................................................................15
1.2.2 Interfaces .....................................................................................................................................17
1.2.3 Status displays .............................................................................................................................18
1.3 Accessories..................................................................................................................................22
2 Safety Instructions ................................................................................................................................ 23
2.1 General safety instructions ..........................................................................................................23
2.2 Notes on use ................................................................................................................................26
3 Installing and connecting the device ...................................................................................................... 29
3.1 Preparing for installation ..............................................................................................................29
3.1.1 Checking the delivery package ....................................................................................................29
3.1.2 Identification data of the device ...................................................................................................30
3.1.3 Permitted mounting positions.......................................................................................................31
3.2 Mounting the device.....................................................................................................................32
3.2.1 Installation guidelines...................................................................................................................32
3.3 Connecting the device .................................................................................................................34
3.3.1 Connection information ................................................................................................................34
3.3.2 Connection of equipotential bonding ...........................................................................................35
3.3.3 Connecting peripheral equipment................................................................................................36
3.3.4 Connecting the power supply.......................................................................................................37
3.3.4.1 Information about the power supply.............................................................................................37
3.3.4.2 Connecting an AC power supply..................................................................................................38
3.3.4.3 Connecting a redundant power supply ........................................................................................39
3.3.5 Connecting the device to networks..............................................................................................40
3.3.6 Securing the lines.........................................................................................................................43
3.3.6.1 Network and fieldbus cables........................................................................................................43
3.3.6.2 COM, DP, DVI/VGA, PS/2 and audio lines..................................................................................44
3.3.7 Multi-monitoring............................................................................................................................44
4 Commissioning the device .................................................................................................................... 45
4.1 General information on commissioning .......................................................................................45
4.2 Switching on the device ...............................................................................................................46
4.3 Automatic switching on of the device...........................................................................................47
4.4 Windows Action Center................................................................................................................47

Table of contents
SIMATIC IPC647D
6Operating Instructions, 01/2014, A5E32996306-AA
4.5 Notes on different device configurations..................................................................................... 48
4.5.1 Opening the front door ................................................................................................................ 48
4.5.2 DVD burner drive ........................................................................................................................ 48
4.5.3 Replacing hard disks................................................................................................................... 49
4.5.4 System with two drives................................................................................................................ 50
4.5.5 RAID1 system ............................................................................................................................. 50
4.6 Switching off the device .............................................................................................................. 51
5 Extended device functions .................................................................................................................... 53
5.1 Monitoring functions .................................................................................................................... 53
5.1.1 Overview of the monitoring functions.......................................................................................... 53
5.1.2 Temperature monitoring/display ................................................................................................. 54
5.1.3 Watchdog (WD) with LED ........................................................................................................... 54
5.1.4 Fan monitoring ............................................................................................................................ 55
5.1.5 Battery monitoring ....................................................................................................................... 55
5.1.6 Drive monitoring .......................................................................................................................... 55
5.2 Active Management Technology (AMT)...................................................................................... 56
5.3 Trusted Platform Module (TPM).................................................................................................. 57
6 Expanding and assigning parameters to the device............................................................................... 59
6.1 Retrofitting instructions................................................................................................................ 59
6.2 Removing the front panel ............................................................................................................ 62
6.3 Open the device. ......................................................................................................................... 63
6.4 Removing and installing memory modules ................................................................................. 64
6.5 Expansion cards.......................................................................................................................... 67
6.5.1 Notes on the expansion cards .................................................................................................... 67
6.5.2 Removing and installing bus frame............................................................................................. 68
6.5.3 Removing and installing expansion cards................................................................................... 70
6.6 Drives and storage media ........................................................................................................... 73
6.6.1 Overview ..................................................................................................................................... 73
6.6.2 Removing and installing drive cage ............................................................................................ 74
6.6.3 Removing and installing drive fans ............................................................................................. 75
6.6.4 Removing and inserting the tray from the removable drive bays................................................ 77
6.6.5 Removing and installing the hard disk drive from a tray ............................................................. 78
6.6.6 Removing and installing a drive from a drive cage ..................................................................... 79
6.6.7 Replacing a defective hard disk drive in the RAID system ......................................................... 80
6.6.8 Removing and installing an SSD ................................................................................................ 81
6.6.8.1 Removing and installing an SSD from a tray .............................................................................. 81
6.6.8.2 Removing and installing an SSD with mounting plate from a drive cage ................................... 82
7 Device maintenance and repair............................................................................................................. 83
7.1 Repair information....................................................................................................................... 83
7.2 Maintenance................................................................................................................................ 84
7.2.1 Maintenance intervals ................................................................................................................. 84
7.2.2 Changing the filter pad ................................................................................................................ 84
7.3 Removing and installing hardware.............................................................................................. 85
7.3.1 Replacing device fans ................................................................................................................. 85

Table of contents
SIMATIC IPC647D
Operating Instructions, 01/2014, A5E32996306-AA 7
7.3.2 Replacing the backup battery ......................................................................................................87
7.3.3 Removing the AC power supply...................................................................................................89
7.3.4 Replacing the redundant power supply .......................................................................................91
7.3.5 Replacing the redundant power supply completely .....................................................................92
7.3.6 Removing and installing the piggyback and bus board ...............................................................94
7.3.7 Removing the OP.........................................................................................................................95
7.3.8 Removing and installing the processor cooler .............................................................................97
7.3.9 Removing the motherboard .........................................................................................................99
7.3.10 Replacing the processor ............................................................................................................101
7.4 Managing RAID systems ...........................................................................................................104
7.4.1 Example for a RAID1 system during the boot phase of the system ..........................................104
7.4.2 RAID software............................................................................................................................105
7.4.3 Checking the status of the RAID system ...................................................................................105
7.4.4 Displaying a defective hard disk of a RAID system in the RAID software.................................106
7.4.5 Points to note if the hard disk in the RAID system is replaced when the computer is
turned off ....................................................................................................................................106
7.4.6 Integrating a new hard disk drive in the RAID system...............................................................107
7.5 Installing the software ................................................................................................................109
7.5.1 Sources for installation of the operating system ........................................................................109
7.5.2 Updating the operating system ..................................................................................................109
7.5.3 Installing drivers and software ...................................................................................................110
7.5.4 Installing Windows 7 or Windows Server 2008 R2 ....................................................................111
7.5.5 Setting up the language selection using the Multilanguage User Interface (MUI).....................114
7.5.6 Restoring the delivery state .......................................................................................................115
7.5.7 Installing the RAID controller software.......................................................................................
116
7.5.8 CP 1616 onboard.......................................................................................................................116
8 Technical specifications ...................................................................................................................... 117
8.1 Certificates and approvals .........................................................................................................117
8.2 Directives and declarations........................................................................................................118
8.2.1 CE marking ................................................................................................................................118
8.2.2 ESD guideline ............................................................................................................................119
8.3 Dimension drawings...................................................................................................................121
8.3.1 Dimensional drawing of the device ............................................................................................121
8.3.2 Dimension drawing of the telescopic rails..................................................................................122
8.3.3 Dimension drawing of the expansion cards ...............................................................................122
8.4 Technical specifications .............................................................................................................123
8.4.1 General specifications................................................................................................................123
8.4.2 Ambient and environmental conditions......................................................................................128
8.4.3 Current and power requirements ...............................................................................................129
8.4.4 Power supply (AC) .....................................................................................................................130
8.4.5 AC power supply, redundant......................................................................................................131
8.4.6 Technical data of the telescopic rails .........................................................................................131
8.5 Hardware description .................................................................................................................132
8.5.1 Motherboard...............................................................................................................................132
8.5.1.1 Structure and functions of the motherboard ..............................................................................132
8.5.1.2 Technical features of the motherboard ......................................................................................133
8.5.1.3 Position of the interfaces on the motherboard ...........................................................................135
8.5.1.4 External interfaces .....................................................................................................................136

Table of contents
SIMATIC IPC647D
8Operating Instructions, 01/2014, A5E32996306-AA
8.5.1.5 Internal ports ............................................................................................................................. 146
8.5.2 Bus board .................................................................................................................................. 153
8.5.2.1 Bus board models ..................................................................................................................... 153
8.5.2.2 PCI hardware interrupts ............................................................................................................ 155
8.5.3 System resources ..................................................................................................................... 159
8.5.3.1 Currently allocated system resources....................................................................................... 159
8.5.3.2 Allocation of the system resources used by BIOS/DOS ........................................................... 159
8.5.4 Displays and operator panel ..................................................................................................... 164
8.5.4.1 Design and function .................................................................................................................. 164
8.5.4.2 Pin assignment of the OP connectors....................................................................................... 164
8.5.5 Communication processor CP 1616 onboard ........................................................................... 165
8.5.5.1 Introduction................................................................................................................................ 165
8.5.5.2 Firmware loader ........................................................................................................................ 167
8.5.5.3 Further actions in STEP 7/NCM PC.......................................................................................... 169
8.6 BIOS description ....................................................................................................................... 169
8.6.1 Overview ................................................................................................................................... 169
8.6.2 Opening the BIOS selection menu............................................................................................ 170
8.6.3 BIOS Setup menus ................................................................................................................... 171
8.6.4 Exit menu .................................................................................................................................. 172
8.6.5 BIOS update.............................................................................................................................. 173
8.6.6 BIOS Setup settings.................................................................................................................. 174
8.6.7 Alarm, error and system messages .......................................................................................... 178
8.6.7.1 Power On Self Test ................................................................................................................... 178
8.6.7.2 BIOS beep codes ...................................................................................................................... 180
8.7 Active Management Technology (AMT).................................................................................... 186
8.7.1 AMT basics................................................................................................................................ 186
8.7.2 Overview of AMT....................................................................................................................... 187
8.7.3 Enabling AMT, basic configuration ........................................................................................... 187
8.7.4 Advanced settings..................................................................................................................... 188
8.7.5 Resetting with Unconfigure ....................................................................................................... 188
8.7.6 Determining the network address ............................................................................................. 189
8.7.7 Forcing user consent................................................................................................................. 189
A Technical support.................................................................................................................................191
A.1 Service and support .................................................................................................................. 191
A.2 Troubleshooting ........................................................................................................................ 192
A.3 RAID system and device startup............................................................................................... 195
A.4 Notes on the use of third-party modules ................................................................................... 196
B Abbreviations.......................................................................................................................................197
Glossary ..............................................................................................................................................203
Index ...................................................................................................................................................215

SIMATIC IPC647D
Operating Instructions, 01/2014, A5E32996306-AA 9
Overview
1
1.1
Product description
The SIMATIC IPC647D is an industrial PC in 19" rack format design. The SIMATIC IPC647D
has the following characteristic features:
●High-performance industrial functionality
●Highly compact
●Extremely rugged
●Extensive product continuity
The SIMATIC IPC offers system integrators, cabinet designers, system engineers and
machine designers a 19" rack PC platform for high-performance applications and IT
applications on the control and cell level for:
●Process and visualization applications
●Industrial image processing
●Quality assurance and monitoring tasks
●Measurement, control and rule-based tasks
●Data acquisition and management
The SIMATIC IPC has CE certification for use in the industrial sector as well as in residential
and commercial areas and small businesses. In addition to the industrial applications,
therefore, it can also be used in building automation or in public facilities.

Overview
1.1 Product description
SIMATIC IPC647D
10 Operating Instructions, 01/2014, A5E32996306-AA
1.1.1
Highlights
Highly compact
●Compact housing design (2 HU)
●Flexibility for space-saving cabinet installation
High degree of industrial capability
●High operational vibration and shock resistance
●Wide operational temperature range
●High service friendliness
●Dust protection
●Distinct diagnostic features
Ideal for industrial applications
●Integrated PROFIBUS DP / MPI interface (optional, compatible with CP5622)
●PROFINET interface CP 1616 onboard (optional)
●PCI, PCIe I/O, PEG slots
PEG graphics and onboard graphics can be used simultaneously
●High flexibility and expansibility of components
High investment protection
●High continuity of the components/design
●Guaranteed spare parts availability for at least 5 years
●Simple integration in PC-based automation
High system availability
●SIMATIC IPC DiagMonitor – PC diagnostics and message software via OPC/SNMP/LAN
●SIMATIC PC/PG Image Creator – data imaging software
●RAID based on SATA hard disks on-board
●RAID1 – redundant data storage on two hard drives, also "hot swap" in connection with
removable drive bays
(Hot Spare equipping is supported)
●Optional ECC memory module
●Redundant power supply with status message

Overview
1.1 Product description
SIMATIC IPC647D
Operating Instructions, 01/2014, A5E32996306-AA 11
1.1.2
Features
General features
Design •19” rack, 2 HU
•Rugged panel-mount housing, all metal
•Prepared for mounting telescopic rails
•Can be mounted horizontally
•Lockable front cover as access protection
Enclosure •Dust protection by
means of overpressure ventilation using
bearing seated front fan through filter
•Enclosure cover fastened with a single screw
•Front fan can be exchanged without tools
•Card retainer for reliable operation of PC modules under
vibration and shock conditions
Drive bays •2 × removable drive bays, slimline or
•2 × 3.5" drive in vibration-damped drive cage and
•1 × slimline DVD format
Slots for expansion cards (long) Max. 4 slots, equipment PCI/PCIe, depending on
configuration
Graphics •CRT (via DVI-I VGA adapter): Up to 2560x1600 at 120 Hz
/ 32-bit color depth
•LCD via DVI-D: Up to 2048 x 1152 at 60 Hz, 32-bit color
depth
•LCD via DisplayPort: Up to 4096 x 1152 at 24 Hz, 32-bit
color depth
Interfaces
PROFIBUS/MPI
12 Mbps (isolated potential, compatible to CP -5622), optional
PROFINET
10/100 Mbps (CP 1616 onboard), three RJ45; optional
Ethernet 2 x 10/100/1000 Mbps (two RJ45)
Wake on LAN, Remote Boot and teaming are supported
USB
2 x front panel, 4 x rear panel, 1 x internal; (high current)
Serial COM1 (V.24), COM2 (V.24) optional, through slot plate
adapter
Parallel
LPT optional, through slot plate adapter
Monitor •1 x DVI-I (for DVI-D or VGA using cable adapter)
•2 × DisplayPort
•2 × DVI-D/VGA with Dual Head graphics card (optional,
via cable adapter)
Keyboard
PS/2
Mouse
PS/2
Audio
Microphone, Line out / Headset
Power supply 100 VAC to 240 VAC, wide range; with short-term power
failure backup in accordance with NAMUR: Max. 20 ms at
0.85 rated voltage

Overview
1.1 Product description
SIMATIC IPC647D
12 Operating Instructions, 01/2014, A5E32996306-AA
Monitoring functions
Temperature •Overshoot/undershoot of permissible operating
temperature
•Messages can be evaluated by an application program.
Fan •Speed monitoring
•Messages can be evaluated by an application program.
Watchdog •Monitoring of the IPC
•Monitoring time can be parameterized in software
•Restart can be parameterized in the event of a fault
•Messages can be evaluated by an application program.
Status LEDs •POWER (internal power supply unit, PC switched On)
•HDD (access to hard disk drive)
•ETHERNET 1, ETHERNET 2 (Ethernet status,
"heartbeat")
•PROFIBUS/MPI (activation display of the PROFIBUS/MPI
interface), optional product feature
•SF PROFINET (status display of the CP 1616 onboard
interface), optional product feature
•WATCHDOG (Watchdog function/error display)
•TEMP (temperature status)
•FAN (speed monitoring)
•HDD0 Alarm, HDD1 Alarm: RAID status message in
conjunction with SIMATIC monitoring software (only with
RAID option)
Basic variant
Motherboard Motherboard without fieldbus,
Intel® DH82C226 Express Chipset
Bus board
PCI, PCIe x4, PCIe x16, 2 variants
Processor •Intel® Xeon™ E3-1268L v3 2.3 (3.3) GHz, 4 cores, GT2,
8 MB SLC, HT
•Intel® Core™ i5-4570TE 2.7 (3.3) GHz, 2 cores, GT2, 4
MB SLC, AMT
•Intel® Core™ i3-4330TE 2.4 GHz, 2 cores, GT2, 3 MB
SLC, AMT
RAM expansion Up to 32 GB SDRAM DDR3 1600MT/s
4 DIMM base with or without ECC
1
Drives
Hard disks
3.5" SATA 6 Gbit/s, 500 GB / 1000 GB
Optical drive
Slimline SATA
1 Memory expansions ≥4 GB can only be used in combination with 64-bit operating systems.

Overview
1.1 Product description
SIMATIC IPC647D
Operating Instructions, 01/2014, A5E32996306-AA 13
Optional accessories
PROFIBUS/MPI
12 Mbps (isolated potential, compatible to CP 5622)
PROFINET
10/100 Mbps (CP 1616 onboard, three RJ45)
Drives
DVD burner Read:
DVD ROM: Single Layer 8x, Dual Layer 6x
DVD-R/+R: Single layer 8x, Dual layer 6x
DVD-RW/+RW 8x, DVD-RAM 5x
CD-ROM/CD-R Read 24x, CD-RW 24x
Write:
DVD+R 8x, DVD+RW 8x, DVD-R 8x, DVD-RW 6x
DVD+R (DL) 6x, DVD-R DL 2x
CD-R 24x, CD-RW 24x
Hard disks 3.5" (SATA) Installation in drive cage (with vibration damping)
•500 / 1000 GB (SATA)
•2 × 1000 GB (SATA)
RAID1: 1000 GB (2 × 1000 GB, SATA)
Installation in the drive cage of the removable drive bay
•500 GB (SATA)
•1000 GB (SATA)
•2 × 1000 GB (SATA)
•RAID1:
1000 GB (2 × 1000 GB, SATA)
Solid State Drive 2.5" (SATA) •240 GB MLC, internal or in removable drive bay
Graphics cards
PCIe x16 graphics card, dual head (2 x VGA or 2 x DVI-D)
DVI-I to VGA adapter Used to connect a monitor with a VGA port to the PC (can be
ordered by configurator).
Operating system Preinstalled and activated, included on restore DVD
•Windows Server 2008 R2, MUI 1, 64 bit
•Windows 7, MUI 1, 32 bit / 64 bit
Power supplies
Redundant AC power supply
Monitored AC-100/230 V power supply, 350 W
1MUI: German, English, French, Spanish and Italian

Overview
1.1 Product description
SIMATIC IPC647D
14 Operating Instructions, 01/2014, A5E32996306-AA
Operating system languages
The following languages for the operating system can be installed from the recovery DVD:
Language
Windows Server 2008 R2
Windows 7
32/64 bit
German
X
X
English
X
X
French
X
X
Italian
X
X
Spanish
X
X
Japanese
X
X
Chinese (Hong Kong)
X
X
Chinese (simplified)
X
X
Chinese (Taiwan)
–
X
Korean
X
X
Russian
X
X
Optional software
SIMATIC IPC DiagMonitor V4.4.2
or higher
Software for monitoring local and remote SIMATIC PCs:
•Watchdog
•Temperature
•Fan speed
•Hard disk monitoring (SMART, RAID status)
•Monitoring modules of the redundant power supply
•System / Ethernet monitoring (Heartbeat)
SIMATIC IPC Image & Partition
Creator V3.3.2 or higher
Software tool for local data backup and setting up of the hard
disks.

Overview
1.2 Design of the device
SIMATIC IPC647D
Operating Instructions, 01/2014, A5E32996306-AA 15
1.2
Design of the device
1.2.1
Device views
Front view
①Front panel with openings for ventilation of the device
⑧
On/off button
⑨Installation option for drives
The following drives can be ordered optionally:
•HDD or SSD in removable drive bay
•DVD burner drive, Slimline
•HDD in vibration-damped drive cage
•SSD in internal drive cage
②Rating plate
③
Front door
④Status displays
⑤Reset button ⑩Lock for front door
⑥
USB 2.0 port
⑦
USB 3.0 port

Overview
1.2 Design of the device
SIMATIC IPC647D
16 Operating Instructions, 01/2014, A5E32996306-AA
Rear view with AC power supply
①
AC power supply
②
Power supply
connection
③
On/off switch
④
Interfaces (Page 17)
⑤Expansion card slots
Rear view with redundant power supply
①
Power supply
connection
②Acknowledgment
button
③
Module 1 of the
redundant power
supply
④Module 2 of the
redundant power
supply
⑤
On/off switch
⑥
Status LED module 1
⑦
Interfaces (Page 17)
⑧Expansion card slots

Overview
1.2 Design of the device
SIMATIC IPC647D
Operating Instructions, 01/2014, A5E32996306-AA 17
1.2.2
Interfaces
Dual-head adapter
The adapter is necessary if
you want to connect one of
two monitors to the optional
Dual Head graphics card.
①
Connection for equipotential bonding
⑨
DVI-I port
②Fieldbus cover: No fieldbus, PROFIBUS or PROFINET 1 ⑩Slot plate adapter with LPT and
COM2 port, optional
③USB ports
Left sockets: Connection for USB 2.0 devices
Right sockets: Connection for USB 3.0 / USB 2.0 devices
USB 2.0 and USB 3.0 connections use different USB ports.
⑪Audio input for analog audio
source or microphone, 3.5 mm
phono jack
④
ETHERNET interfaces 1 and 2
LAN interfaces are numbered on the enclosure to provide unique
identification. The numbering by the operating system may deviate from this.
⑫
Audio output for active speakers
or headset, 3.5 mm phono jack
⑤COM interface ⑬Slots for expansion cards
(behind slot plate)
⑥
DisplayPort port
⑭
DMS59 connector
⑦
PS/2 interface for keyboard
⑮
DVI-I connector
⑧PS/2 interface for mouse ⑯VGA adapter
1Depending on the ordered device configuration

Overview
1.2 Design of the device
SIMATIC IPC647D
18 Operating Instructions, 01/2014, A5E32996306-AA
1.2.3
Status displays
Front panel
View with open front door
Operating
display
Meaning
LED
Description
POWER Operating mode of
the PC
Off PC disconnected from power supply
Yellow
PC in standby
Green
PC in operation
HDD Access to hard disk
Off
No access
Green
Access
ETHERNET 1 1 Status connection
ETHERNET
Off •No connection
Lit green •Connection
•No data traffic
ETHERNET 2 1Flashes green
according to
activity
•Connection
•Data traffic
PROFIBUS/MPI
(optional)
Status connection
S7 or PROFIBUS
Off •No connection
•No data traffic
Green
Data traffic
SF PROFINET,
optional
Status
CP 1616 onboard
Off •CP not available
•CP disabled
•No error, communication established
•Charging in progress
•CP 1616 driver not installed
•CP in NDIS mode

Overview
1.2 Design of the device
SIMATIC IPC647D
Operating Instructions, 01/2014, A5E32996306-AA 19
Flashes
slowly
•Link status error
•IO controller: IO device cannot be
addressed
•IO controller: Duplicate IP address
Flashes
rapidly
Exception error: diagnostics via Web or
SNMP is no longer possible
On •Diagnostics information available
•No communication established.
WATCHDOG WATCHDOG status
Off
WATCHDOG not activated
Green
WATCHDOG monitoring enabled
Red
Monitoring time elapsed
TEMP Temperature status
Off
Internal temperature OK
Red
Internal temperature critical
FAN Fan status
(only with active
SOM or
DiagMonitor
software)
Off
Fan speed OK
Red Fan speed too low
HDD0 ALARM
HDD1 ALARM
HDD alarm in
connection with
RAID and
monitoring software
Off
RAID is OK
Red 1 x
HDD0 or HDD1 not OK
Red 2 x RAID is not OK
Localization of the hard disk see Section
"Displaying a defective hard disk of a RAID
system in the RAID software (Page 106)"
Both flash
RAID is synchronized
All displays are
lit
Error in early BIOS
Post
All lit CPU has not started up
Error in early POST
1
For unique labeling, the Ethernet ports are numbered on the enclosure. The numbering by the
operating system may deviate from this.

Overview
1.2 Design of the device
SIMATIC IPC647D
20 Operating Instructions, 01/2014, A5E32996306-AA
Ethernet interface
Display
Meaning
LED
Description
Ethernet 1, 2 1Green LED
Link status display
Off •No cable connected
•Cable disabled
•Interface disabled, 10 MBit
cable active
Green
100 Mbit cable active
Orange
1000 Mbit cable active
Yellow LED
Activity status display
Off •No cable connected
•Cable disabled
•Interface disabled
Lit •Connection
•No activity
Goes out
briefly
Activity
PROFINET LAN X1
P1, P2, P3 1
Green LED
Link status display of CP-
1616 channel
Off •No cable connected
•Cable disabled
•Interface disabled
Green Active cable connected
Yellow LED
Activity status display of
CP-1616 channel
Off •No cable connected
•Cable disabled
•Interface disabled
Lit •Connection
•No activity
Goes out
briefly
Activity
1
For unique labeling, the LAN and PROFINET interface are numbered on the enclosure. The
numbering by the operating system may deviate from this.