Siemens SITRANS FUH1010 Specification sheet

201 SOUTH HOUSTON AVE.
TULSA, OK 74127
PHONE [phone]
WWW.ERNIEGRAVES.COM
PRODUCT INSTRUCTION MANUAL V1.0
MAY 2016
SITRANS LIQUID ULTRASONIC FLOWMETER / INTERFACE DETECTOR (IFD)
MODELS: FUH1010

_
_________________
_
FUH1010 IP65 NEMA 4X
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
_
_______
_
__________
1
Introduction
2
Safety notes
3
Description
SITRANS F
4
Installing/mounting
Ultrasonic Flowmeters
5
FUH1010 IP65 NEMA 4X
and IP66 NEMA 7
Precision Volume
Connecting
6
Commissioning
Operating Instructions 7
Functions
Alarm, error and system
messages
8
Service and maintenance 9
10
Troubleshooting
11
Technical Data
A
Appendix A
B
Appendix B
01/2013
A5E32122003-AA

Siemens AG
Industry Sector
Postfach 48 48
90026 NÜRNBERG
GERMANY
Order number: A5E32122003
Ⓟ 06/2013 Technical data subject to change
Copyright © Siemens AG 2013.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

Table of contents
1 Introduction................................................................................................................................................ 9
1.1 Items supplied................................................................................................................................9
1.2 History............................................................................................................................................9
1.3 Further Information ......................................................................................................................10
2 Safety notes............................................................................................................................................. 11
2.1 Warning Symbols.........................................................................................................................11
2.2 Laws and directives .....................................................................................................................12
2.3 Lithium batteries...........................................................................................................................13
2.4 Installation in hazardous area......................................................................................................13
2.5 Safety Notes.................................................................................................................................16
2.6 Certificates ...................................................................................................................................20
3 Description............................................................................................................................................... 21
3.1 FUH1010 features........................................................................................................................21
3.2 NEMA 4X & NEMA 7 Transmitters ..............................................................................................21
3.3 Applications..................................................................................................................................23
3.4 Theory of Operation .....................................................................................................................24
4 Installing/mounting................................................................................................................................... 31
4.1 Installation safety precautions......................................................................................................31
4.2 Determining a location .................................................................................................................31
4.3 Application Guidelines .................................................................................................................32
4.4 Mounting the Transmitter.............................................................................................................32
5 Connecting .............................................................................................................................................. 35
5.1 Safety notes for connecting .........................................................................................................35
5.2 Transmitter Wiring........................................................................................................................37
5.2.1 Connecting Power........................................................................................................................37
5.2.2 Wiring Temperature Sensor to Transmitter .................................................................................39
5.3 Sensor Wiring...............................................................................................................................43
5.3.1 Wiring the Sensors.......................................................................................................................43
5.4 Navigating the Menu ....................................................................................................................45
5.5 Programming the Transmitter ......................................................................................................46
5.6 Sensor Installation .......................................................................................................................50
5.6.1 Preliminary Installation Procedures .............................................................................................50
5.6.2 Sensor Identification and Selection .............................................................................................52
FUH1010 IP65 NEMA 4X Precision Volume
Operating Instructions, 01/2013, A5E32122003-AA 3

Table of contents
FUH1010 IP65 NEMA 4X Precision Volume
4 Operating Instructions, 01/2013, A5E32122003-AA
5.6.3 Reflect Mount .............................................................................................................................. 56
5.6.4 Direct Mount................................................................................................................................ 58
5.6.5 1012T Mounting Tracks .............................................................................................................. 63
5.7 Mounting Temperature Sensors ................................................................................................. 71
6 Commissioning ........................................................................................................................................ 73
6.1 General requirements ................................................................................................................. 73
6.2 Commissioning............................................................................................................................ 73
6.3 Empty Pipe Set ........................................................................................................................... 75
6.4 Installation Menus ....................................................................................................................... 78
7 Functions................................................................................................................................................. 83
7.1 Setting Liquid Parameters........................................................................................................... 83
7.2 Selecting Flow Units.................................................................................................................... 89
7.3 Span Data ................................................................................................................................... 94
7.4 Analog Out Setup........................................................................................................................ 99
7.5 Analog Input Setup.................................................................................................................... 101
7.6 Expanded I/O Option................................................................................................................. 104
7.7 Logger Control .......................................................................................................................... 108
7.8 Setting Thermal Coefficient and Modulus of Elasticity.............................................................. 111
7.9 Operation Adjust Menu Settings ............................................................................................... 113
7.10 Setting Relays ........................................................................................................................... 115
7.11 Memory Control......................................................................................................................... 118
7.12 Analog Output Trim ................................................................................................................... 119
7.13 Resistive Temperature Device (RTD) Calibration..................................................................... 122
7.14 SONILOCATOR Operation ....................................................................................................... 125
8 Alarm, error and system messages ....................................................................................................... 129
8.1 Alarm Codes ............................................................................................................................. 129
8.2 Alarms ....................................................................................................................................... 130
9 Service and maintenance ...................................................................................................................... 133
9.1 Maintenance.............................................................................................................................. 133
9.2 Technical support...................................................................................................................... 133
9.3 Transportation and storage....................................................................................................... 134
9.4 Repair........................................................................................................................................ 135
9.4.1 Unit repair.................................................................................................................................. 135
9.5 Return and disposal .................................................................................................................. 136
9.5.1 Return procedures (incl lithium batteries) ................................................................................. 136
9.5.2 Battery disposal......................................................................................................................... 137
9.5.3 Disposal..................................................................................................................................... 138

Table of contents
FUH1010 IP65 NEMA 4X Precision Volume
Operating Instructions, 01/2013, A5E32122003-AA 5
10 Troubleshooting..................................................................................................................................... 139
10.1 Troubleshooting .........................................................................................................................139
10.2 F4 Reset Procedure...................................................................................................................141
10.3 Test Facilities Graph Screen......................................................................................................142
10.4 Site Setup Data..........................................................................................................................152
10.5 Force Transmit...........................................................................................................................157
11 Technical Data....................................................................................................................................... 161
A Appendix A ............................................................................................................................................ 163
A.1 Ordering .....................................................................................................................................163
A.2 I/O Connections and Wiring.......................................................................................................163
A.3 RS-232 Connection....................................................................................................................177
A.4 Flowrate Calibration and Calibration Tables..............................................................................186
B Appendix B ............................................................................................................................................ 191
B.1 Installation/Outline Drawings .....................................................................................................191
Glossary ................................................................................................................................................ 193
Index...................................................................................................................................................... 199
Tables
Table 5- 1 Keypad Function Chart ................................................................................................................46
Table 5- 2 Temperature Sensors ..................................................................................................................71
Table 7- 1 Common Liquid Classes ..............................................................................................................86
Table 7- 2 Liquid Table Data.........................................................................................................................86
Table 7- 3 Totalizer Modes ...........................................................................................................................90
Table 7- 4 Totalizer Controls (the "n" in <Fn> = channel number)* ..............................................................93
Table 7- 5 Input/Output Wiring (TB2) - 7ME39400AL03 Expanded I/O Module...........................................96
Table 7- 6 Open Collector User Resistor Recommendations.......................................................................97
Table 7- 7 Analog Outputs ............................................................................................................................99
Table 7- 8 Analog Out Setup Data Categories .............................................................................................99
Table 7- 9 I/O Data Control Menu...............................................................................................................101
Table 7- 10 Typical 2-Channel Flow Meter Expanded I/O Option Connections ...........................................106
Table 7- 11 Logger Control Menu Option List...............................................................................................108
Table 7- 12 Relay Option List........................................................................................................................116
Table 7- 13 Memory Control Menu ...............................................................................................................118
Table 7- 14 Analog Out Trim Menu Structure ...............................................................................................119
Table 7- 15 RTD Calibrate Menu Structure...................................................................................................122

Table of contents
FUH1010 IP65 NEMA 4X Precision Volume
6 Operating Instructions, 01/2013, A5E32122003-AA
Table 10- 1 Troubleshooting Tips..................................................................................................................139
Table 10- 2 Description of Graph Screen Text Display Parameters.............................................................150
Table 10- 3 Hot Key Summary ......................................................................................................................151
Table 10- 4 Site Setup Menu Items...............................................................................................................152
Table A- 1 Connection Diagrams and Part Numbers ..................................................................................163
Table A- 2 Input/Output Wiring (TB2) - 7ME39400AL00 and 7ME39400AL01 I/O Module ........................165
Table A- 3 Input/Output Wiring (TB3) - 7ME39400AL00 and 7ME39400AL01 I/O Module ........................166
Table A- 4 Connection Diagrams and Part Numbers ..................................................................................167
Table A- 5 Input/Output Wiring (TB2) - 7ME39400AL03 and 7ME39400AL04 Expanded I/O Module.......169
Table A- 6 Input/Output Wiring (TB3) - 7ME39400AL03 and 7ME39400AL04 Expanded I/O Module.......170
Table A- 7 Input/Output Wiring (TB4) - 7ME39400AL03 and 7ME39400AL04 Expanded I/O Module.......171
Table A- 8 Connection Diagrams and Part Numbers ..................................................................................172
Table A- 9 Input/Output Wiring (TB2) - 7ME39400AL04 Expanded I/O Module.........................................174
Table A- 10 Open Collector User Resistor Recommendations .....................................................................175
Table A- 11 Input/Output Wiring (TB3) - 7ME39400AL04 Expanded I/O Module.........................................175
Table A- 12 Input/Output Wiring (TB4) - 7ME39400AL04 Expanded I/O Module.........................................176
Figures
Figure 3-1 Typical Transmitter Label.............................................................................................................22
Figure 3-2 NEMA 4X Transmitter Case.........................................................................................................22
Figure 3-3 NEMA 7 Transmitter Enclosure with graphic display and keypad. ..............................................23
Figure 4-1 Pipe Mounting and Mounting Locations for Transmitter ..............................................................33
Figure 5-1 Input Power (J10) Wiring..............................................................................................................38
Figure 5-2 Analog Input Module Access........................................................................................................40
Figure 5-3 Single Channel Temperature Sensor Inputs................................................................................41
Figure 5-4 Sensor Cable Connections ..........................................................................................................44
Figure 5-5 Software Version (xx.xx.xx)..........................................................................................................45
Figure 5-6 Keypad .........................................................................................................................................45
Figure 5-7 Pipe Surface Preparation.............................................................................................................51
Figure 5-8 Universal Sensor Label ................................................................................................................53
Figure 5-9 Hi Precision Sensor Label............................................................................................................54
Figure 5-10 Sensor Installation........................................................................................................................57
Figure 5-11 Sensor..........................................................................................................................................58
Figure 5-12 Mylar Spacing Guide....................................................................................................................59

Table of contents
FUH1010 IP65 NEMA 4X Precision Volume
Operating Instructions, 01/2013, A5E32122003-AA 7
Figure 5-13 Wrap Strap Under Pipe and Attach to Adjusting Screw...............................................................60
Figure 5-14 Wrapping the Mylar Spacing Guide around the pipe (End View) ................................................61
Figure 5-15 Finding the Halfway Distance ......................................................................................................62
Figure 5-16 Aligning the Sensors for Direct Mode operation (End View) .......................................................62
Figure 5-17 Reflect Mount with Model 1012TN Mounting Track (Side View) .................................................65
Figure 5-18 Direct Mount 180° opposed with Mounting Tracks ......................................................................67
Figure 5-19 Track Rail Alignment....................................................................................................................69
Figure 5-20 REF and Number Index Pin Locations ........................................................................................70
Figure 5-21 Clamp-on Temperature Sensor ...................................................................................................71
Figure 5-22 Insert Temperature Sensor..........................................................................................................72
Figure 6-1 EmptyPipeSet_Actual-MTY_Fill ...................................................................................................76
Figure 6-2 Typical Installation Menu Screen.................................................................................................82
Figure 7-1 PGEN Wiring Diagram .................................................................................................................96
Figure 10-1 Test Facilities Graph Screen......................................................................................................143
Figure 10-2 Setting Digital Damping Factor ..................................................................................................146
Figure 10-3 Setting the MinDamp Factor ......................................................................................................147
Figure 10-4 Envelope Threshold Adjustment................................................................................................149
Figure A-1 7ME39400AL00 and 7ME39400AL01 I/O Module.....................................................................164
Figure A-2 7ME39400AL03 and 7ME39400AL04 Expanded I/O Module ...................................................168
Figure A-3 7ME39400AL04 Expanded I/O Module .....................................................................................173
Figure A-4 1015CPC-N Serial Interface Cable............................................................................................178

Table of contents
FUH1010 IP65 NEMA 4X Precision Volume
8 Operating Instructions, 01/2013, A5E32122003-AA

Introduction 1
These instructions contain all information required to commission and use the device. It is
your responsibility to read the instructions carefully prior to installation and commissioning. In
order to use the device correctly, first review its principle of operation.
The instructions are aimed at persons mechanically installing the device, connecting it
electronically, configuring the parameters and commissioning it, as well as service and
maintenance engineers.
1.1 Items supplied
● SITRANS F Transmitter
● SITRANS F literature CD
● For additional items refer to your packing slip.
Inspection
1. Check for mechanical damage due to possible improper handling during shipment. All
claims for damage are to be made promptly to the shipper.
2. Make sure the scope of delivery, and the information on the type plate corresponds to the
ordering information.
1.2 History
The following table shows the most important changes in the documentation compared to
each previous edition.
Edition Remarks
01/2013 First Edition of the Operating Instructions for the SITRANS FUH1010 IP65 NEMA 4X and
IP66 NEMA 7 Precision Volume flow meter.
FUH1010 IP65 NEMA 4X Precision Volume
Operating Instructions, 01/2013, A5E32122003-AA 9

Introduction
1.3 Further Information
FUH1010 IP65 NEMA 4X Precision Volume
10 Operating Instructions, 01/2013, A5E32122003-AA
1.3 Further Information
Product information on the Internet
The Operating Instructions are available on the CD-ROM shipped with the device, and on
the Internet on the Siemens homepage, where further information on the range of SITRANS
F flowmeters may also be found:
Product information on the internet (http://www.siemens.com/flow)
Worldwide contact person
If you need more information or have particular problems not covered sufficiently by these
Operating Instructions, get in touch with your contact person. You can find contact
information for your local contact person on the Internet:
Local contact person (http://www.automation.siemens.com/partner)
The contents of this manual shall not become part of or modify any prior or existing
agreement, commitment or legal relationship. The sales contract contains all obligations on
the part of Siemens as well as the complete and solely applicable warranty conditions. Any
statements regarding device versions described in the manual do not create new warranties
or modify the existing warranty.
The content reflects the technical status at the time of publishing. Siemens reserves the right
to make technical changes in the course of further development.

Safety notes 2
This device left the factory in good working condition. In order to maintain this status and to
ensure safe operation of the device, observe these instructions and all the specifications
relevant to safety.
Observe the information and symbols on the device. Do not remove any information or
symbols from the device. Always keep the information and symbols in a completely legible
state.
2.1 Warning Symbols
Symbol Explanation
Consult operating instructions
Hot surface
Dangerous electrical voltage
Corrosive materials
Toxic materials
Isolate the device from power using a circuit-breaker
Protect the device from impact otherwise loss of degree of protection
Protective insulation; device in protection class II
FUH1010 IP65 NEMA 4X Precision Volume
Operating Instructions, 01/2013, A5E32122003-AA 11

Safety notes
2.2 Laws and directives
FUH1010 IP65 NEMA 4X Precision Volume
12 Operating Instructions, 01/2013, A5E32122003-AA
2.2 Laws and directives
General requirements
Installation of the equipment must comply with national regulations. For example, the
National Electrical Codes.
Instrument safety standards
The device has been tested at the factory, based on the safety requirements. In order to
maintain this condition over the expected life of the device the requirements described in
these Operating Instructions must be observed.
NOTICE
Material compatibility
Siemens can provide assistance with the selection of sensor parts. However, the full
responsibility for the selection rests with the customer and Siemens can take no
responsibility for any failure due to material incompatibility.
CE marked equipment
The CE-mark symbolizes the compliance of the device with the following Directives:
● EMC-Directive 2004/108/EC
● Low voltage Directive 2006/95/EC
● Pressure equipment Directive (PED) 97/23/EC
● ATEX Directive 94/9/EC

Safety notes
2.3 Lithium batteries
FUH1010 IP65 NEMA 4X Precision Volume
Operating Instructions, 01/2013, A5E32122003-AA 13
2.3 Lithium batteries
Lithium batteries are primary power sources with high energy content designed to represent
the highest possible degree of safety.
WARNING
Potential hazard
Lithium batteries may present a potential hazard if they are abused electrically or
mechanically.
Observe the following precautions when handling and using lithium batteries:
– Do not short-circuit, recharge or connect with false polarity.
– Do not expose to temperature beyond the specified temperature range or incinerate
the battery.
– Do not crush, puncture or open cells or disassemble battery packs.
– Do not weld or solder to the battery’s body.
– Do not expose contents to water.
2.4 Installation in hazardous area
WARNING
Explosion Hazard
Equipment used in hazardous areas must be Ex-approved and marked accordingly.
It is required that the special conditions for safe use provided in the manual and in the Ex
certificate are followed!
Hazardous area approvals
The device is approved for use in hazardous area and has the following approval:
● FM and CSA certified
- Class I, Division 1, Groups ABCD
- Class II, Division 1, Groups EFG
● ATEX

Safety notes
2.4 Installation in hazardous area
FUH1010 IP65 NEMA 4X Precision Volume
14 Operating Instructions, 01/2013, A5E32122003-AA
WARNING
Explosion Hazard
Devices without the correct hazardous area approval create dangerous environments.
Make sure the hazardous area approval is suitable for the environment in which the
device will be installed.
Intrinsically safe data
WARNING
Explosion Hazard
User must install unit with Siemens drawings. With intrinsically safe circuits, use only
certified meters appropriate for the transmitter.
If a non-conforming supply unit is used, the "fail-safe" type of protection will no longer be
effective and the approval certification will be invalid.
Hazardous area safety requirements
It is required that:
● Electrical connections are in accordance with EN60079-14 (Installing Electrical Systems
in Explosion Hazardous Areas).
● The protective cover over the power supply is properly installed. For intrinsically safe
circuits the connection area can be opened.
● Appropriate cable connectors are used for the output circuits:
– Intrinsically safe: blue
– Non-intrinsically safe: black
● Sensor and transmitter are connected to the potential equalization.
For intrinsically safe output circuits potential equalization must be maintained along the
entire connection path.
● When protective earth (PE) is connected, no potential difference between the protective
earth (PE) and the potential equalization (PA) can exist, even during a fault condition.

Safety notes
2.4 Installation in hazardous area
FUH1010 IP65 NEMA 4X Precision Volume
Operating Instructions, 01/2013, A5E32122003-AA 15
WARNING
Explosion Hazard
"Flameproof enclosure" type of protection
Only open devices with type of protection "Flameproof enclosure" (e.g. FUT1010 NEMA
7) in hazardous areas when the power to the device is turned off, otherwise there is a
risk of explosion.
WARNING
Explosion Hazard
Laying Cables
Cable for use in zone 1 and 2 must satisfy the requirements for having a proof voltage <
AC 500 V applied between the conductor/ground, conductor/shield and shield/ground.
Connect the devices that are operated in hazardous areas as per the stipulations
applicable in the country of operation, e.g. for Ex "d" and "nA", permanent cables must
be laid.
WARNING
Explosion Hazard
Devices with the common approval "Intrinsically safe" and "Flameproof"
The following is applicable for devices with the common approval "Intrinsically safe" and
"Flameproof" (Ex ia + Ex d): Before commissioning, make sure that the type of
protection that is not suitable is permanently defaced on the nameplate to avoid
improper use.
If a non-conforming infeed is used, the "fail-safe" type of protection will no longer be
effective.

Safety notes
2.5 Safety Notes
FUH1010 IP65 NEMA 4X Precision Volume
16 Operating Instructions, 01/2013, A5E32122003-AA
2.5 Safety Notes
Safety Information for Hazardous Areas
DANGER
Explosion Hazard
Will Cause Death, Serious Injury or Property Damage.
Restrict use and repair to qualified personnel.
DANGER
Explosion Hazard
Death or severe personal injury and/or equipment and property damage will result if proper
Hazardous (Classified) Locations installation precautions are not taken.
Restrict use and repair to qualified personnel.
DANGER
Explosion Hazard
The use of unauthorized parts in the repair of the equipment, tampering by unqualified
personnel, or operation with the cover open in a Hazardous (Classified) Location will result
in dangerous conditions which will cause death, serious injury, and/or equipment and
property damage.
Restrict use and repair to qualified personnel.
Follow all safety instructions contained or referenced herein.
DANGER
Explosion Hazard
Death or severe personal injury and/or equipment and property damage will result due to
improper installation or use of this equipment when located in a Hazardous (Classified)
Location.
Install as directed.
Disconnect power source before servicing.
Keep cover closed when equipment is operating.

Safety notes
2.5 Safety Notes
FUH1010 IP65 NEMA 4X Precision Volume
Operating Instructions, 01/2013, A5E32122003-AA 17
WARNING
Qualified personnel
This flowmeter system may only be set up and used in conjunction with this document and
the instructions on the electronic media provided. Installation, maintenance and operation
of the flowmeter system may only be performed by qualified personnel. Within the context
of this Document, qualified persons are defined as persons who have the skills and
knowledge related to the construction and operation of the electrical equipment and
installations and have received safety training to recognize and avoid the potentially
explosive hazards involved.
Qualified personnel posses the following qualifications
1. Is trained and authorized to energize, de-energize, clear, ground and tag circuits and
equipment in accordance with established safety practices.
2. Is trained in the proper care and use of protective equipment such as rubber gloves,
hard hat, safety glasses or face shields, flash clothing, etc., in accordance with
established safety practices.
3. Is trained in rendering first aid.
Note
This document does not purport to cover all details or variations in equipment, or to provide
for every possible contingency to be met in connection with installation, operation or
maintenance. Should further information be desired or should particular problems arise,
which are not covered sufficiently for the purchaser's purposes, the matter should be
referred to the local Siemens sales office (www.automation.siemens.com/partner). The
contents of this Document shall not become part of or modify any prior or existing
agreement, commitment or relationship. The sales contract contains the entire obligation of
Siemens. The warranty contained in the contact between the parties is the sole warranty of
Siemens. Any statements contained herein do not create new warranties or modify the
existing warranty.
Safety Information for Hazardous Areas
Note
Ratings under this heading apply to specific model families.
Check Your Model Number: FUH1010, 7ME3600-0, 7ME3600-3 only.
FM-CSA installation
Read, understand and follow all safety instructions on the electronic media provided. This
equipment is rated for use in hazardous (classified) locations as stated below and must be
installed according to the 1010-304 installation drawing provided on the media. Failure to
install the equipment in the prescribed manner will result in unsafe operation. Follow all local
jurisdictional safety codes when operating this equipment. When properly installed the
equipment meets the following FM – CSA ratings.

Safety notes
2.5 Safety Notes
FUH1010 IP65 NEMA 4X Precision Volume
18 Operating Instructions, 01/2013, A5E32122003-AA
Transmitter
● Intrinsically safe connections Class I and II, Division 1, Groups A, B, C, D, E, F and G;
● Nonincendive for Class I, Division 2, Groups A, B, C and D;
● Suitable for Class II, Division 2, Groups E, F and G outdoor (Type 4X), Class III (CSA
only)
● Temperature code T5 at an ambient of 40°C
Sensors
● Intrinsically safe Class I and II, Division 1, Groups A, B, C, D, E, F and G;
● Nonincendive for Class I, Division 2, Groups A, B, C and D;
● Suitable for Class II, Division 2, Groups E, F and G outdoor (Type 4X), Class III (CSA
only)
● Temperature code T6 at an ambient of 40°C
ATEX installation
Read, understand and follow all safety instruction on the electronic media provided. This
equipment complies with Directive 94/9/EC and is rated for use in potentially explosive
atmospheres. The equipment markings are shown and explained below. Equipment must be
installed according to the 1010-389 installation drawing provided on the media. Failure to
install the equipment in the prescribed manner will result in unsafe operation. Follow all
regional safety laws when operating this equipment. When properly installed the equipment
meets the following ATEX ratings as stated in EC-Type Examination Certificate
KEMA03ATEX1134
Transmitter Markings and Explanations
● II (1) G [Ex ia] IIC – Transmitter located in the non-hazardous area with intrinsically
safe circuits of category Ex ia, which can be connected to Category 1 Sensors
● II 3 (1) G Ex nC [ia] IIC T5 Tamb = 0 to +50°C – Category 3 Transmitter located in
Ex
● ght and against liquid,
xplanations
Zone 2 potentially explosive atmosphere area with intrinsically safe circuits of category
ia, which can be connected to Category 1 Sensors in Zone 0
IP65 – Ingress protection against solid bodies, rating of dust-ti
rating of water jets
Sensor Markings and E
● II I G Ex ia IIC T5 Ga Tamb = +60°C – Category 1 Sensors located in Zone 0
r use in potentially explosive atmosphere with intrinsically safe circuits of category Ex ia fo
potentially explosive atmosphere containing gases

Safety notes
2.5 Safety Notes
FUH1010 IP65 NEMA 4X Precision Volume
Operating Instructions, 01/2013, A5E32122003-AA 19
Safety Information for Hazardous Areas
Note
Ratings under this heading apply to specific model families.
Check Your Model Number: FUH1010, 7ME3603-0, 7ME3603-3
FM-CSA installation
Read, understand and follow all safety instruction on the electronic media provided. This
equipment is rated for use in hazardous (classified) locations as stated below and must be
installed according to the 1010-443 installation drawing provided on the media. Failure to
install the equipment in the prescribed manner will result in unsafe operation. Follow all local
jurisdictional safety codes when operating this equipment. When properly installed the
equipment meets the following FM – CSA ratings:
Transmitter
● Explosionproof for Class I, Division1, Groups B, C, D;
● Dust-ignitionproof for Class II, Division 1, Groups E, F and G
● Intrinsically safe connections for Class I and II, Division 1, Groups A, B, C, D, E, F and G;
● Nonincendive for Class I, Division 2, Groups A, B, C and D;
● Suitable for Class II, Division 2, Groups E, F and G outdoor (Type 4X), Class III (CSA
only)
Sensors
● Intrinsically safe Class I and II, Division 1, Groups A, B, C, D, E, F and G;
● Nonincendive for Class I, Division 2, Groups A, B, C and D;
● Suitable for Class II, Division 2, Groups E, F and G outdoor (Type 4X), Class III (CSA
only)
● Temperature code T6 at an ambient of 40°C
ATEX installation
Read, understand and follow all safety instruction on the electronic media provided. This
equipment is rated for use in explosive atmospheres as stated below and must be installed
according to the 1010-464 installation drawing provided on the media. Failure to install the
equipment in the prescribed manner will result in unsafe operation. Follow all regional safety
laws when operating this equipment. When properly installed the equipment meets the
following ATEX ratings as stated in EC-Type Examination Certificate KEMA03ATEX1134