Siemens MAMMOMAT 1000 Nova User manual

MAMMOMAT 1000/3000 Nova - Opdimar
English
Print No.: SPB7-230.812.06.01.02 Doc. Gen. Date: 03.03
Replaces: n.a. 66 53 914
© Siemens AG 2003
The reproduction, transmission or
use of this document or its contents
is not permitted without express
written authority. Offenders will be
liable for damages. All rights,
including rights created by patent
grant or registration of a utility
model _or_design,_are_reserved.
SP
Installation
Settings for LCD monitor (SCD 1897 TFT)
Installation Instructions

Opdima® SPB7-230.812.06 Page 2 of 4 Siemens-Elema AB
Installation Rev. 01 03.03 SPS-UD Solna, Sweden
0 - 2 Revision
Document revision level
The document corresponds to the version/revision level effective at the time of system delivery. Revi-
sions to hardcopy documentation are not automatically distributed.
Please contact your local Siemens office to order current revision levels.
Disclaimer
The installation and service of equipment described herein is to be performed by qualified personnel
who are employed by Siemens or one of its affiliates or who are otherwise authorized by Siemens or
one of its affiliates to provide such services.
Assemblers and other persons who are not employed by or otherwise directly affiliated with or autho-
rized by Siemens or one of its affiliates are directed to contact one of the local offices of Siemens or
one of its affiliates before attempting installation or service procedures.
Chapter Page Revision
All All 01

Contents 0 - 3
Siemens-Elema AB SPB7-230.812.06 Page 3 of 4 Opdima®
Solna, Sweden Rev. 01 03.03 SPS-UD Installation
1 _______General_______________________________________________________1 - 1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 - 1
Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1
Time required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1
2 _______ASW 2.1 ______________________________________________________2 - 1
Adjusting resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1
Adjusting image geometry. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1
3 _______ASW 3.1 ______________________________________________________3 - 1
Adjusting resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 1
Adjusting image geometry. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 1
Page

0 - 4 Contents
Opdima® SPB7-230.812.06 Page 4 of 4 Siemens-Elema AB
Installation Rev. 01 03.03 SPS-UD Solna, Sweden
This page intentionally left blank.

1 - 1
Siemens-Elema AB SPB7-230.812.06 Page 1 of 2 Opdima®
Solna, Sweden Rev. 01 03.03 SPS-UD Installation
General 1
Introduction 1
These instructions describe how to adjust the resolution and the image geometry of
LCD monitor SCD 1897 TFT.
For acquisition workstation software version ASW 2.1, follow the instructions in chapter 2.
For software version ASW 3.1, follow the instructions in chapter 3.
Prerequisites 1
The monitor should be installed according to chapter "Installation of monitor" in document
Installation and Start-Up Instructions (SPB7-230.033.13...).
Time required 1
Approximately 1/2 hour for one CSE.