Siemens ARCADIS Orbic Installation manual

© Siemens AG
The reproduction, transmission or use
of this document or its contents is not
permitted without express written
authority. Offenders will be liable for
damages. All rights, including rights
created by patent grant or registration
of a utility model or design, are
reserved.
Print No.:
Würthwein
ARCADIS Orbic
System
Installation and Startup
SP
2005
SPR2-320.814.03.02.02
Replaces: SPR2-320.814.03.01.02
English
Doc. Gen. Date: 06.05
3D Navigation
08080009

2 Revision / Disclaimer
ARCADIS Orbic SPR2-320.814.03.02.02 Siemens AG
06.05 CS SD 24
Page 2 of 16 Medical Solutions
1Revision / Disclaimer
Document revision level
The document corresponds to the version/revision level effective at the time of system
delivery. Revisions to hardcopy documentation are not automatically distributed.
Please contact your local Siemens office to order current revision levels.
Disclaimer
The installation and service of equipment described herein is to be performed by qualified
personnel who are employed by Siemens or one of its affiliates or who are otherwise
authorized by Siemens or one of its affiliates to provide such services.
Assemblers and other persons who are not employed by or otherwise directly affiliated
with or authorized by Siemens or one of its affiliates are directed to contact one of the
local offices of Siemens or one of its affiliates before attempting installation or service pro-
cedures.

Siemens AG SPR2-320.814.03.02.02 ARCADIS Orbic
06.05 CS SD 24
Table of Contents 3
Page 3 of 16
Medical Solutions
1- 0Table of Contents
1 _______ Prerequisites ___________________________________________________ 4
3D navigation with the ARCADIS Orbic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
General requirement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Required documents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
System requirement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Required parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Required license key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Functional check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2 _______ Installation and settings __________________________________________ 7
Work sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installing the TCP/IP cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Attaching the HW interface to the image intensifier . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Attaching the identification label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Configuring the network node . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Final work steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3 _______ Changes to the previous versio ___________________________________ 15

4 Prerequisites
ARCADIS Orbic SPR2-320.814.03.02.02 Siemens AG
06.05 CS SD 24
Page 4 of 16 Medical Solutions
2-
1Prerequisites
3D navigation with the ARCADIS Orbic 0
Fig. 1: Navigation systems
Fig. 2: 3D_marker ring
The 3D navigation kit is a universal HW and SW interface which serves navigation sys-
tems from different navigation companies (Fig.1/p.4).
The navigation system itself is supplied by a navigation company.
The supplied grid holder on the image intensifier is usually the interface to the “removable
marker ring”. An engineer from the navigation company is responsible for attaching the
active or passive marker ring (Fig.2/p.4)to the I.I. of the Is C 3D.

Siemens AG SPR2-320.814.03.02.02 ARCADIS Orbic
06.05 CS SD 24
Prerequisites 5
Page 5 of 16
Medical Solutions
A Siemens engineer is responsible for attaching the grid holder to the image intensifier,
testing and loading the SW, calibration without the marker ring on the I.I., as well as con-
figuration.
An additional calibration must be performed with the navigation system installed (marker
ring on the I. I.). Therefore, an engineer from the navigation company must be participate
in the calibration.
Two engineers use a test body to check the interaction of the two systems and the overall
accuracy.
The test body always remains with the customer.
The overlap time of the two engineers is approx. 2 hours.
The navigation system is handed over by the navigation company.
General requirement 0
Support for startup from the navigation company should be provided on site.
Required documents 0
System requirement 0
ARCADIS system software VB11 or higher.
Required parts 0
TCP/IP type cross-over cable for a direct connection to the navigation system (not
included in the shipment).
TCP/IP cable for a connection to the navigation system via the clinical network (not
included in the shipment).
3D navigation kit: 80 81 452
Required license key 0
System configuration SPR2-320.843.02.01.02
Image quality test SPR2-320.820.02.01.02
3D navigation license key Part No.: 80 81 528
3D license key Part No.: 80 81 502

6 Prerequisites
ARCADIS Orbic SPR2-320.814.03.02.02 Siemens AG
06.05 CS SD 24
Page 6 of 16 Medical Solutions
Tools 0
Tool kit
Safety information 0
WARNING Risk of physical injury or death and property damage!
Non-compliance can lead to death, physical injury or property
damage.
Strictly follow:
¹The product-specific safety information in these instruc-
tions
¹The general safety information in the instructions
TD00-000.860.01...
¹The general safety information according to ARTD part 2.
Functional check 0
•Prior to the installation of the 3D navigation kit, check that the system is functioning
properly.
•Visually inspect the 3D navigation kit and the calibration phantom with navigation inter-
face to ensure they are in good condition.

Siemens AG SPR2-320.814.03.02.02 ARCADIS Orbic
06.05 CS SD 24
Installation and settings 7
Page 7 of 16
Medical Solutions
3-
2Installa tion and setting s
Work sequence 0
Installing the TCP/IP cable 0
•Plug the TCP/IP cross-over cable into the monitor trolley and into the 3D navigation
system (see figure below).
NOTE If the ARCADIS system is connected to the navigation system via
the clinical network, there can be problems if the load on the clin-
ical network is heavy.
Fig. 3: Plug
Attaching the HW interface to the image intensifier 0
Fig. 4: I.I._01

8 Installation and settings
ARCADIS Orbic SPR2-320.814.03.02.02 Siemens AG
06.05 CS SD 24
Page 8 of 16 Medical Solutions
Fig. 5: I.I._02
Fig. 6: I.I._03

Siemens AG SPR2-320.814.03.02.02 ARCADIS Orbic
06.05 CS SD 24
Installation and settings 9
Page 9 of 16
Medical Solutions
Fig. 7: I. I. _ new
•Remove the screws of the grid holder (Fig.4/p.7).
•Detach the microswitch, pinch it off and insulate the cable with insulating tape
(Fig.5/p.8).
•Detach the grid from the grid holder. The gaskets are no longer needed.
•Apply a little silicone 20 48 981 all around the fitting of the grid holder 75 51 703 and
press down the grid, making sure it is correctly positioned in the grid holder.
NOTICE Ensure the grid is properly oriented in the grid holder and the
C-arm assembly is correctly oriented.
¹See (Fig.7/p.9)
•Wait for the silicone to harden (approx. 30 min.).
•Attach the grid holder to the I.I. and secure it with screws 11 22 571 and contact wash-
ers 34 16 666.

10 Installation and settings
ARCADIS Orbic SPR2-320.814.03.02.02 Siemens AG
06.05 CS SD 24
Page 10 of 16 Medical Solutions
Attaching the identification label 0
Fig. 8: Label
•Attach the identification label 75 51 828 to the unit as shown in the illustration.
Configuring the network node 0
•Switch on the system.
•Click <Options> - <Service> - <Local Service>.
•Enter the password and click <ok>.
•Click <Configuration>.
•“Attached to Network” and “Dicom Networking” must be selected.
•Click <Next>.