Siemens CIM User manual

CIM
CIM
Operating Manual
11/2022
A5E51250518
-AC
Preface
Application and functions
1
Structure of the device
2
Security
3
Mounting and connecting
the device
4
Web-based configuration
5
CIM SGLAN Connector
6
Practical example
7
Dimension drawing
8
Technical specifications
9
Technical support
A

Siemens AG
Digital Industries
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E51250518-AC
Ⓟ
10/2022 Subject to change
Copyright © Siemens AG 2022.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

CIM
Operating Manual, 11/2022, A5E51250518-AC 3
Preface
Purpose of the documentation
This manual describes communication interface module (CIM).
This manual supports you during the configuration, installation and operation of the
communication modules.
Product names and abbreviations
•CIM or device
In this document, the term "CIM" or "device" is also used instead of the full product name
"CIM“. CIM is the abbreviation for Communication Interface Module.
Use of the device
Please observe notes marked as follows:
Note
A note contains important information on the product described in the documentation, on
the handling of the product or on the section of the documentation to which particular
attention should be paid.
Note
To prevent injury, read the manual before use.
The manual is delivered online, you can download the document from Central technical
support (https://support.industry.siemens.com/cs/ww/en/).
History
Edition
Comment
09/2021
First Edition
07/2022
Added Description for UKCA certification.
11/2022
•Supported setting up SGLAN for devices from different site with CIM.
•Added monitor variables in CIM web-based configuration.

CIM
4Operating Manual, 11/2022, A5E51250518-AC
Table of contents
Preface................................................................................................................................................... 3
1 Application and functions ..................................................................................................................... 7
1.1 What's new in CIM 1.1?........................................................................................................ 7
1.2 Functions ............................................................................................................................ 8
1.3 Requirements for use......................................................................................................... 10
1.4 Universal Data Model......................................................................................................... 11
1.5 SGLAN............................................................................................................................... 14
1.6 Accessories........................................................................................................................ 15
2 Structure of the device ........................................................................................................................ 16
2.1 Appearance of the device................................................................................................... 16
2.2 LEDs to display operation................................................................................................... 17
2.3 The "RESET" button ............................................................................................................ 18
2.4 Slots for SIM card and cellular module................................................................................ 18
3 Security................................................................................................................................................ 20
3.1 Security information .......................................................................................................... 20
3.2 Data protection.................................................................................................................. 20
3.3 Important notes on using the device .................................................................................. 21
4 Mounting and connecting the device ................................................................................................. 24
4.1 Mounting the device.......................................................................................................... 24
4.1.1 Mounting position ............................................................................................................. 24
4.1.2 DIN rail mounting .............................................................................................................. 26
4.1.3 Wall-mounting................................................................................................................... 27
4.2 Connecting the device ....................................................................................................... 28
4.2.1 Notes on connecting.......................................................................................................... 28
4.2.2 Connecting the power supply and function earth ............................................................... 29
4.2.3 Connecting the LAN interface ............................................................................................ 31
4.3 Installing expansion modules............................................................................................. 31
4.3.1 Open the device ................................................................................................................ 31
4.3.2 Installing the SMA connector ............................................................................................. 34
4.3.3 Insert the SIM card............................................................................................................. 35
4.3.4 Installing the Cellular module............................................................................................. 37
4.3.5 Connecting the antenna .................................................................................................... 39
5 Web-based configuration .................................................................................................................... 41
5.1 Security recommendations ................................................................................................ 41
5.2 Downloading and installing the certificate.......................................................................... 42

Table of contents
CIM
Operating Manual, 11/2022, A5E51250518-AC 5
5.2.1 Overview........................................................................................................................... 42
5.2.2 Installing the certificate for Windows ................................................................................. 43
5.2.3 Installing the certificate for Mac OS.................................................................................... 44
5.2.4 Installing the certificate for Linux ....................................................................................... 44
5.3 Accessing web-based configuration from PC....................................................................... 45
5.4 Web pages......................................................................................................................... 47
5.4.1 Layout of CIM .................................................................................................................... 47
5.4.2 Device information ............................................................................................................ 48
5.4.3 LAN settings ...................................................................................................................... 49
5.4.4 SGLAN Setting ................................................................................................................... 49
5.4.4.1 Setting up SGLAN server .................................................................................................... 49
5.4.4.2 Setting up SGLAN client ..................................................................................................... 50
5.4.5 Contacts ............................................................................................................................ 54
5.4.6 Data management ............................................................................................................. 55
5.4.6.1 Variables ........................................................................................................................... 55
5.4.6.2 Messages........................................................................................................................... 56
5.4.6.3 Data Binding...................................................................................................................... 58
5.4.6.4 Online Monitor .................................................................................................................. 61
5.4.7 Protocol Settings................................................................................................................ 62
5.4.7.1 Overview for multi-protocol ............................................................................................... 62
5.4.7.2 S7...................................................................................................................................... 62
5.4.7.3 Modbus TCP....................................................................................................................... 66
5.4.7.4 Modbus RTU ...................................................................................................................... 70
5.4.7.5 RESTful API ........................................................................................................................ 72
5.4.8 Cellular and GNSS .............................................................................................................. 75
5.4.8.1 Cellular status.................................................................................................................... 75
5.4.8.2 Cellular settings................................................................................................................. 76
5.4.8.3 Extra initialization commands ............................................................................................ 77
5.4.8.4 GNSS settings .................................................................................................................... 77
5.4.9 Security ............................................................................................................................. 77
5.4.9.1 Protocol............................................................................................................................. 77
5.4.9.2 Certificates ........................................................................................................................ 78
5.4.9.3 IP address management..................................................................................................... 82
5.4.10 System settings ................................................................................................................. 83
5.4.10.1 Time settings..................................................................................................................... 83
5.4.10.2 Power on/off SMS .............................................................................................................. 85
5.4.10.3 Change password .............................................................................................................. 85
5.4.10.4 System reset...................................................................................................................... 85
5.4.10.5 System configuration management.................................................................................... 86
5.4.10.6 System upgrade................................................................................................................. 86
6 CIM SGLAN Connector ......................................................................................................................... 88
6.1 Installation ........................................................................................................................ 89
6.2 Working with CIM SGLAN Connector .................................................................................. 90
6.2.1 Certificate setting .............................................................................................................. 90
6.2.2 Server list .......................................................................................................................... 91
6.2.3 Connecting to SGLAN server .............................................................................................. 92
6.2.4 Viewing SGLAN connection................................................................................................ 93
7 Practical example................................................................................................................................. 94
7.1 Application example .......................................................................................................... 94

Table of contents
CIM
6Operating Manual, 11/2022, A5E51250518-AC
7.1.1 Fill control ......................................................................................................................... 94
7.2 SGLAN example ................................................................................................................. 95
7.2.1 Download program to LOGO! BM remotely......................................................................... 95
7.2.2 Download Network project with LOGO!Soft Comfort remotely.......................................... 101
8 Dimension drawing ........................................................................................................................... 111
9 Technical specifications..................................................................................................................... 112
9.1 Technical specification..................................................................................................... 112
9.2 Certificates and approvals................................................................................................ 113
A Technical support .............................................................................................................................. 120
A.1 Service and support ......................................................................................................... 120
A.2 Troubleshooting .............................................................................................................. 120
A.3 SGLAN troubleshooting.................................................................................................... 123
Index.................................................................................................................................................. 124

CIM
Operating Manual, 11/2022, A5E51250518-AC 7
Application and functions
1
1.1 What's new in CIM 1.1?
The features described below are only used for CIM 1.1.
New functions
CIM V1.1 provides the following new features:
•Support setting up SGLAN with CIM
–SGLAN (Page 14) (Secured Global Local Area Network) is used for setting up virtual LAN
for devices from different sites
–Siemens CIM SGLAN Connector: application for connecting PC to SGLAN as SGLAN
client
–SGLAN page (Page 49) on CIM web-based configuration
•Monitor online variables through web-based configuration
•Allow to add extra initialization commands (Page 77) for cellular modular
Changed functions
CIM web-based configuration:
•Add new page for monitoring online variables (Page 61)
•Add columns for monitoring and modifying in variable page (Page 55)
•Add speed, altitude of CIM in GNSS page (Page 77)
•Add IP address change notify (Page 82).

Application and functions
1.2 Functions
CIM
8Operating Manual, 11/2022, A5E51250518-AC
1.2 Functions
CIM provides Internet connection solution for LOGO! BM which has more and more
capabilities to interact with Internet now.
General introduction
Universal Data Model (UDM)
LOGO! BM and Modbus RTU compatible devices can map their process data to UDM. UDM
acts as a data center for CIM, and different protocols can exchange data through UDM.
4 ports switch
CIM can work as a LAN switch.
To ensure CIM work stably and efficiently, Siemens recommends that you should connect less
than 4 devices to CIM through Ethernet switch ports.
General gateway
CIM can access the Internet with cellular module and SIM card. LOGO! BM or Modbus RTU
compatible devices can access the internet by connecting to CIM.

Application and functions
1.2 Functions
CIM
Operating Manual, 11/2022, A5E51250518-AC 9
SGLAN
Devices distributed in the same SGLAN (Secured Global Local Area Network) can
communicate with each other.
Basic functions
The CIM supports the following functions:
•Web-based configuration
A Web-based user interface (Web-based configuration) for the configuration of the CIM.
•Protocol gateway
LOGO! BM and Modbus RTU compatible devices can communicate with CIM via
S7/Modbus protocol based on the Universal Data Model (UDM).
Application can access data through RESTful API on CIM based on UDM.
•Data management
CIM can perform an action when a configured event is triggered.
–After configured, CIM can perform an action, for example, change the data in UDM,
send one or more short messages to one or more contacts.
•Mobile cellular
With the CIM, you can establish a mobile data connection to a mobile cellular network.
•GNSS position
–Display the position information on the web page
–Enable/disable map the position data to UDM
•Time Server
–CIM can act as an NTP server to provide time for LOGO! BM or other NTP client.
–CIM can enable/disable mapping the time to the Universal Data Model (UDM). Then the
device without NTP can get the time via multi-protocol or RESTful API.
•Power on/off SMS
–CIM can send a power on/off SMS to one defined contact.
•Certificate
–Owned certificate: generate and select certificate for setting up a secured web server
and a SGLAN server
–Trusted certificate: select certificate for setting up SGLAN Client
Web-based configuration
You can configure the CIM locally using a web-based configuration that can be displayed with
a Web browser. The web-based configuration provides the following functions:
•Configure the LAN of CIM
•Manage the contacts

Application and functions
1.3 Requirements for use
CIM
10 Operating Manual, 11/2022, A5E51250518-AC
•Configure variables, messages and data bindings
•Modify and monitor variables
•Configure the multi-protocol
•Configure the cellular module
•Set the system time and synchronization of the CIM
•Configure the security functions
•Maintenance functions such as firmware update, device restart and factory reset
•Set the power on/off SMS for CIM
For more detailed information, refer to Web-based configuration (Page 41).
1.3 Requirements for use
Requirements for operation
•Cellular module (mini PCIe)
To operate the CIM in its entirety, you require a cellular module that is compatible to CIM
and the standard of the cellular network you are using. For more information, refer to the
section Slots for SIM card and cellular module (Page 18).
•Antenna and cables
Only use antennas from the accessories program for the CIM. For more information, refer
to the section Antennas (Page 39).
–Antenna for cellular
To access the cellular network, you require an antenna that is adapted to the standard
of the cellular network you are using.
–Antenna for GNSS
If you want to use GNSS, you require a suitable GNSS antenna.
•Mobile data contract with SIM card
To use the mobile data communication via the WAN interface of the CIM, you require a
contract with a suitable cellular network operator.
•Cellular network
To be able to use the cellular interface, there must be a cellular network within the reach
of the CIM.
•Data contract
For the following data services, you require a data contract with your mobile operator:
NTP, Cloud, HTTPS, SGLAN via cellular network

Application and functions
1.4 Universal Data Model
CIM
Operating Manual, 11/2022, A5E51250518-AC 11
Power supply
You require a voltage source with a voltage between 12 VDC and 24 VDC that provides
adequate voltage or current. For more information, refer to the section Technical
specifications (Page 112).
SIM card
You require a SIM card of your mobile cellular operator.
Recommendations
Note the following recommendations for the cellular contract or for the SIM card:
•Where possible sign a cellular contract with a provider that makes all required functions
available.
To send SMS messages, the SIM card must be enabled this function and have a phone
number.
•Where possible sign a fixed cellular contract and do not use prepaid cards. A flat rate for
SMS and data can be recommended.
If, however, you want to use a prepaid card note the following:
–If your credit has been used up, the CIM does not send an automatic warning.
–You can query your current credit with your provider.
•Where possible, use a standard SIM card without an adapter.
•If the SIM card has been assigned a PIN code, you need to enter the PIN code in the page
"Cellular & GNSS -->Cellular status" of web-based configuration.
•The following access data for the cellular network must be present:
–Access Point Name (APN)
–Dial Number
For more information, refer to the section Cellular settings (Page 76).
Compatible cards
The card receptacle of the CIM for the SIM card is compatible with the following card formats:
•Mini SIM card, 25 x 15 mm (ISO/IEC 7810 ID-000)
1.4 Universal Data Model
“Universal Data Model (UDM)” allows compatible PLC devices map their process data to UDM
even if they use different communication protocols. UDM acts as a data center for CIM, and
different protocols can exchange data through UDM.
Note
UDM uses Little Endian to store its multi-byte type data.

Application and functions
1.4 Universal Data Model
CIM
12 Operating Manual, 11/2022, A5E51250518-AC
I, Q, M, V constructed a data model to simulate the process image in PLC.
Naming rule for the UDM address: address type + short data type + start address. No byte
alignment, for example, VW3 means the word consist of Byte 3 and Byte 4 in area V.
The UDM address is case insensitive.
Data type (Short
data type)
Length Value range I
（512
Bytes）
Q
（512
Bytes）
M
（512
Bytes）
V
(W: 896 Bytes
R: 1024 Bytes)
bool (x)
1 bit
0 ~ 1
0.0-511.7
0.0-511.7
0.0-511.7
0.0-895.7
0.0-
1023.7
byte (b)
8 bit
0 ~ FF
0-511
0-511
0-511
0-895
0-1023
word (w)
16 bit
0 ~ FFFF
0-510
0-510
0-510
0-894
0-1022
double-word (dw)
32 bit
0 ~ FFFFFFFF
0-508
0-508
0-508
0-892
0-1020
long-word (lw)
64 bit
0 ~ FFFFFFFFFFFFFFFF
0-504
0-504
0-504
0-888
0-1016
short-int (si)
8 bit
-128 ~127
0-511
0-511
0-511
0-895
0-1023
int (i)
16 bit
-32768 ~ 32767
0-510
0-510
0-510
0-894
0-1022
double-int (di)
32 bit
-2147483648 ~ 2147483647
0-508
0-508
0-508
0-892
0-1020
long-int (li)
64 bit
-9223372036854775808 ~
9223372036854775807
0-504
0-504
0-504
0-888
0-1016
Real (r)
32 bit
-3.4E38 ~ +3.4E38
0-508
0-508
0-508
0-892
0-1020
long-real (lr)
64 bit
-1.797E308 ~ +1.797E308
0-504
0-504
0-504
0-888
0-1016
short-unsigned
(su)
8 bit
0 ~ 255
0-511
0-511
0-511
0-895
0-1023
unsigned (u)
16 bit
0 ~ 65535
0-510
0-510
0-510
0-894
0-1022
double -unsigned
(du)
32 bit 0 ~ 4294967295 0-508 0-508 0-508 0-892 0-1020
long-unsigned (lu)
64 bit
0 ~ 18446744073709551615
0-504
0-504
0-504
0-888
0-1016

Application and functions
1.4 Universal Data Model
CIM
Operating Manual, 11/2022, A5E51250518-AC 13
System variable
SV (System variable) is used to save some system data, such as, position, time, power state,
mini PCIe module information and so on.
Item Type Size Ad-
dress
Range Unit comments Sample for Restful
Interface
Time
valid flag bool 1 bit 896.
0
0 or 1 Valid flag for the time value /pi/rest/vx896.0
UNIX
timestamp
double
unsigned
4 bytes
897
0 ~
429496729
5
second
Current time, seconds since
1970-1-1 00:00:00
Unit: second
/pi/rest/vdu897
year
unsigned
2 bytes
901
1970 ~
2106
year
Current data, year
/pi/rest/vu901
month
short
unsigned
1 bytes
903
1 ~12
month
Current data, month
/pi/rest/vsu903
day
short
unsigned
1 bytes
904
1 ~ 31
day
Current data, month day
/pi/rest/vsu904
hour
short
unsigned
1 bytes
905
0 ~ 23
hour
Current time, hour
/pi/rest/vsu905
minute
short
unsigned
1 bytes
906
0 ~ 59
minute
Current time, minute
/pi/rest/vsu906
second short
unsigned
1 bytes 907 0 ~ 59 second Current time, second /pi/rest/vsu907
Position
valid flag
bool
1 bit
916.
0
0 or 1
Valid flag for all the position
value
/pi/rest/vx916.0
latitude
short int
1 byte
917
-1 or 1
1: N; -1: S
/pi/rest/vsi917
short
unsigned 1 byte 918 0 ~ 90 degree Latitude's degree
Unit: degree
/pi/rest/vsu918
short
unsigned
1 byte
919
0 ~ 59
minute
Latitude's minute
Unit: minute
/pi/rest/vsu919
short
unsigned
1 byte
920
0 ~ 59
second
Latitude's second
Unit: second
/pi/rest/vsu920
real
4 bytes
921
0 ~ 90.0
degree
Latitude's degree in float for-
mat
Unit: degree
/pi/rest/vr921
longitude
short int
1 byte
925
-1 or 1
1: E; -1: W
/pi/rest/vsi925
short
unsigned 1 byte 926 0 ~ 90 degree Longitude's degree
Unit: degree
/pi/rest/vsu926
short
unsigned 1 byte 927 0 ~ 59 minute Longitude's minute
Unit: minute
/pi/rest/vsu927
short
unsigned
1 byte
928
0 ~ 59
second
Longitude's second
Unit: second
/pi/rest/vsu928
real
4 bytes
929
0 ~ 90.0
degree
Longitude's degree in float
format
Unit: degree
/pi/rest/vr929
altitude
1
int
2 bytes
940
-9999 ~
9999
m
altitude (integer part)
/pi/rest/vi940

Application and functions
1.5 SGLAN
CIM
14 Operating Manual, 11/2022, A5E51250518-AC
Item Type Size Ad-
dress
Range Unit comments Sample for Restful
Interface
short
unsigned
1 byte
942
0 ~ 9
0.1 m
altitude (fractional part)
/pi/rest/vsu942
real 4 bytes 943 -9999.9 ~
9999.9
m altitude in float format /pi/rest/vr943
speed
1
unsigned
2 bytes
933
0 ~ 9999
km/h
speed (integer part)
/pi/rest/vu933
short
unsigned
1 byte
935
0 ~ 9
0.1 km/h
speed (fractional part)
/pi/rest/vu935
real
4 bytes
936
0 ~ 9999.9
km/h
speed in float format
/pi/rest/vu936
1available for CIM V1.1 and later versions.
1.5 SGLAN
SGLAN (secured global local area network) allows you to create a private network with CIM.
SGLAN is the fundamental building block for your private network. Devices in the SGLAN can
communicate with each other securely.

Application and functions
1.6 Accessories
CIM
Operating Manual, 11/2022, A5E51250518-AC 15
Roles in SGLAN
There are two roles in SGLAN:
•SGLAN server: SGLAN server is the data switch center. SGLAN server is responsible for
transmitting data, authorizing connect request, dealing with login and logout request.
Note
Only CIM can work as SGLAN server. Each SGLAN server can connect 2 SGLAN clients
maximum.
•SGLAN client: after joining the SGLAN, SGLAN client and devices in the same LAN with
SGLAN client can communicate with other devices joined SGLAN like in a same LAN.
SGLAN client can be a CIM device or PC with Siemens CIM SGLAN Connector installed.
SGLAN Page on CIM web-based configuration
You can configure the SGLAN in the web-based configuration (Page 49).
Siemens CIM SGLAN Connector
After installing Siemens CIM SGLAN connector on your host computer, you can connect to a
target SGLAN server and communicate with the device in SGLAN remotely. For more
information on the Siemens CIM SGLAN Connector, refer to Siemens CIM SGLAN Connector
Help.
CIM SGLAN Connector supports the following system:
•Windows: Window 10
1.6 Accessories
This chapter contains the scope of accessories valid at the time these operating instructions
were written. The following accessories are not included in the scope of delivery and can be
ordered separately.
Name
Description
Order number
Extended cable
Flexible connecting
cable preassembled
SIMATIC NET N-
Connect/SM male/male
1 m long
6XV1875-5LH10
2 m long
6XV1875-5LH20
5 m long
6XV1875-5LH50
Antenna
Antenna ANT 895-6ML, active GNSS antenna
6GK5895-6ML00-0AA0
Cylinder shaped antenna ANT 896-4ME for
GSM (2G), UMTS (3G) and LTE (4G), ANT896-
4ME
6GK5896-4ME00-0AA0
IRC antenna ANT 896-4MA for GSM (2G),
UMTS (3G) and LTE (4G),ANT896- 4MA
6GK5896-4MA00- 0AA3
Cellular module (mini-
PCIe card)
Telit LE910C1-EU LTE CAT-1 mPCIe
Telit LE910C1-AP LTE CAT-1 mPCIe
Telit LE910C1-NF LTE CAT-1 mPCIe
SIM7600G-H LTE CAT-4 mPCIe

CIM
16 Operating Manual, 11/2022, A5E51250518-AC
Structure of the device
2
2.1 Appearance of the device
Front view
①
RESET button
②
X80 (L+, M, FE) Power supply connector
③
LED
④
FE terminal for shield cable
⑤
X20 (FE, A, B, C, D, E) Multiplex serial interface
⑥
For more information about the device, scan the QR code
Top view
①
Holes for RF antenna

Structure of the device
2.2 LEDs to display operation
CIM
Operating Manual, 11/2022, A5E51250518-AC 17
Rear view
①
Mounting slides
②
Mounting interlock for DIN rail
Bottom view
①
4 × RJ45 Ethernet 10/100 Mbps
2.2 LEDs to display operation
The LEDs on the CIM provide information about the operating status of the device.
Meaning of the LEDs
LED
Status
Meaning
System diag-
nose (DIAG)
On
The LED light is green when CIM is in RUN mode.
On
CIM is booting or waiting for firmware update.
Flash
CIM is updating firmware.

Structure of the device
2.3 The "RESET" button
CIM
18 Operating Manual, 11/2022, A5E51250518-AC
LED
Status
Meaning
On
Firmware is crashed.
Red flashing CIM is powered by capacitor.
LAN (P1, P2, P3,
P4)
Flash
Port is receiving or sending data across Ethernet.
On
Port is already connected to Ethernet.
Off No connection to Ethernet.
mPCIe
Off
The cellular module is not detected.
Flash
The cellular module is initializing or registering.
On
The cellular module has initialized and registered successfully.
Flash
The cellular module is receiving/sending data.
2.3 The "RESET" button
The RESET button allows you to recovery the module to a factory default setting.
Operator input
Function
Keep pressing for longer than 10 seconds
Recovery the module to a default status
2.4 Slots for SIM card and cellular module
Both slots are behind the top housing.
Slot for the SIM card
Compatible cards
Mini SIM card, 25 x 15 mm (ISO/IEC 7810 ID-000)

Structure of the device
2.4 Slots for SIM card and cellular module
CIM
Operating Manual, 11/2022, A5E51250518-AC 19
Inserting the SIM card is described in the section Insert the SIM card (Page 35).
Slot for the cellular module
Compatible cellular modules:
GSM/GPR
S
UMTS LTE Certificate
Telit LE910C1-EU LTE CAT-1 mPCIe
Y
Y
Y
GCF, RED, FCC, JATE/TELEC, RCM
Telit LE910C1-AP LTE CAT-1 mPCIe
Y
Y
Telit LE910C1-NF LTE CAT-1 mPCIe
Y
Y
SIM7600G-H LTE CAT-4 mPCIe
Y
Y
Y
GCF, CE-RED, FCC, PTCRB, IC, Anatel, KC,
NCC, JATE/TELEC, RCM, ICASA, IMDA, SRRC,
CCC
Note
Applicability
The table shows the approvals that may be available. For the device itself, it is certificated as
shown on the product label and package label.
Note
CIM with Telit series wireless module and SIM7600G
-H LTE CAT-
4 mPCIe are certified with UL,
IECEx,ATEX,FM,RCM.
CE
-RED: test with wireless module Telit LE910C1-EU LTE CAT-1 mPCIe and SIM7600G-H LTE
CAT
-4 mPCIe
UKCA
-RED: test with wireless module Telit LE910C1-EU LTE CAT-1 mPCIe and SIM7600G-H
LTE CAT
-4 mPCIe
FCC: test with wireless module Telit LE910C1
-NF LTE CAT-1 mPCIe and SIM7600G-H LTE CAT-
4 mPCIe
Card errors / diagnostics
Card errors are indicated by the "mPCIe" LED.
Inserting the card
Inserting the SIM card is described in the section Installing the Cellular module (Page 37).

CIM
20 Operating Manual, 11/2022, A5E51250518-AC
Security
3
3.1 Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is
necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial
security concept. Siemens’ products and solutions constitute one element of such a concept.
Customers are responsible for preventing unauthorized access to their plants, systems,
machines and networks. Such systems, machines and components should only be connected
to an enterprise network or the internet if and to the extent such a connection is necessary
and only when appropriate security measures (e.g. firewalls and/or network segmentation)
are in place.
For additional information on industrial security measures that may be implemented, please
visit (https://www.siemens.com/industrialsecurity).
Siemens' products and solutions undergo continuous development to make them more
secure. Siemens strongly recommends that product updates are applied as soon as they are
available and that the latest product versions are used. Use of product versions that are no
longer supported, and failure to apply the latest updates may increase customers' exposure to
cyber threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS
Feed visit (https://www.siemens.com/cert).
3.2 Data protection
Siemens observes the data protection guidelines, especially the requirements regarding data
minimization (privacy by design). This means the following for this product: The product does
not process / save any personal information, but only technical functional data (e.g. time
stamps). If the user links this data to other data (e.g. shift plans) or if the user saves personal
information on the same medium (e.g. hard disk) and therefore creates a personal reference
in the process, the user has to ensure meeting the guidelines regarding data protection.